115 lines
2.5 KiB
Ada
115 lines
2.5 KiB
Ada
with Board; use Board;
|
|
|
|
with STM32.RCC; use STM32.RCC;
|
|
with Chip.Units; use Chip.Units;
|
|
with STM32.GPIO; use STM32.GPIO;
|
|
with STM32.USART; use STM32.USART;
|
|
|
|
with Ada.Real_Time; use Ada.Real_Time;
|
|
|
|
procedure UART_429Disco is
|
|
--UART_Port: GPIO_Registers renames GPIOA;
|
|
--UART_TX_Bit: constant Port_Bit_Number := 9;
|
|
--UART_RX_Bit: constant Port_Bit_Number := 10;
|
|
|
|
--UART_Module: USART_Registers renames USART1;
|
|
|
|
procedure UART_Transmit(Data : String) is
|
|
begin
|
|
for I of Data loop
|
|
while not UART_Module.SR.TXE loop
|
|
null;
|
|
end loop;
|
|
UART_Module.DR := Character'Pos(I);
|
|
end loop;
|
|
end;
|
|
|
|
APB2_Frequency : constant := 90_000_000; -- Set by board support
|
|
Baud : constant := 115_200;
|
|
--Ratio : constant := (APB2_Frequency + Baud_Rate / 2) / Baud_Rate;
|
|
|
|
Period: constant Time_Span := Milliseconds(100);
|
|
Now: Time := Clock;
|
|
|
|
begin
|
|
UART_Port_RCC_EN := True;
|
|
|
|
UART_RCC_EN := True;
|
|
|
|
UART_RCC_RST := True;
|
|
UART_RCC_RST := False;
|
|
|
|
UART_Port.AFR(UART_TX_Bit) := UART_AF;
|
|
UART_Port.MODER(UART_TX_Bit) := Alternate_Mode;
|
|
UART_Port.OSPEEDR(UART_TX_Bit) := Low_Speed;
|
|
UART_Port.OTYPER(UART_TX_Bit) := Push_Pull_Type;
|
|
UART_Port.PUPDR(UART_TX_Bit) := Pull_Down;
|
|
|
|
UART_Port.AFR(UART_RX_Bit) := UART_AF;
|
|
UART_Port.MODER(UART_RX_Bit) := Alternate_Mode;
|
|
UART_Port.OSPEEDR(UART_RX_Bit) := Low_Speed;
|
|
UART_Port.OTYPER(UART_RX_Bit) := Push_Pull_Type;
|
|
UART_Port.PUPDR(UART_RX_Bit) := Pull_Down;
|
|
|
|
declare
|
|
R : Control_Register_1 := UART_Module.CR1;
|
|
begin
|
|
R.UE := False;
|
|
UART_Module.CR1 := R;
|
|
end;
|
|
|
|
declare
|
|
R : Control_Register_1 := UART_Module.CR1;
|
|
begin
|
|
R.M := Word_8_Bits;
|
|
R.PCE := False;
|
|
R.PS := Even_Parity;
|
|
R.TE := True;
|
|
R.RE := True;
|
|
R.OVER8 := False;
|
|
|
|
UART_Module.CR1 := R;
|
|
end;
|
|
|
|
declare
|
|
R : Control_Register_2 := UART_Module.CR2;
|
|
begin
|
|
R.STOP := Stop_1_Bit;
|
|
R.LINEN := False;
|
|
R.CLKEN := False;
|
|
|
|
UART_Module.CR2 := R;
|
|
end;
|
|
|
|
declare
|
|
R : Control_Register_3 := UART_Module.CR3;
|
|
begin
|
|
R.SCEN := False;
|
|
R.HDSEL := False;
|
|
R.IREN := False;
|
|
R.RTSE := False;
|
|
R.CTSE := False;
|
|
|
|
UART_Module.CR3 := R;
|
|
end;
|
|
|
|
--UART_Module.BRR := (DIV_Mantissa => Ratio / 16, DIV_Fraction => Ratio mod 16, others => 0);
|
|
UART_Module.BRR := Baud_Rate (Speed => Baud, OVER8 => False, Bus_Frequency => APB2_Frequency);
|
|
|
|
declare
|
|
R : Control_Register_1 := UART_Module.CR1;
|
|
begin
|
|
R.UE := True;
|
|
UART_Module.CR1 := R;
|
|
end;
|
|
|
|
loop
|
|
|
|
UART_Transmit("Hello World! ... ");
|
|
|
|
Now := Now + Period;
|
|
delay until Now;
|
|
end loop;
|
|
|
|
end UART_429Disco;
|