This version is long awaited and the important improvements related to
FreeBSD are:
- USB device type autodetection for some devices
http://sourceforge.net/apps/trac/smartmontools/wiki/Supported_USB-Devices
- Support for HighPoint RocketRAID controllers
- Support RAID controllers using /dev/pass devices
- Support CHECK_POWER_MODE and WRITE_LOG
- Fix CCISS file descriptor leak
- New device type detection algorithm on FreeBSD, not based on filename
- Support for the adaX (ATA on CAM bus) devices on FreeBSD 8.0 and higher
PR: ports/141371
Submitted by: Alex Samorukov <samm os2 kiev ua>
Approved by: marck (maintainer)
Specifically, newer autoconf (> 2.13) has different semantic of the
configure target. In short, one should use --build=CONFIGURE_TARGET
instead of CONFIGURE_TARGET directly. Otherwise, you will get a warning
and the old semantic may be removed in later autoconf releases.
To workaround this issue, many ports hack the CONFIGURE_TARGET variable
so that it contains the ``--build='' prefix.
To solve this issue, under the fact that some ports still have
configure script generated by the old autoconf, we use runtime detection
in the do-configure target so that the proper argument can be used.
Changes to Mk/*:
- Add runtime detection magic in bsd.port.mk
- Remove CONFIGURE_TARGET hack in various bsd.*.mk
- USE_GNOME=gnometarget is now an no-op
Changes to individual ports, other than removing the CONFIGURE_TARGET hack:
= pkg-plist changed (due to the ugly CONFIGURE_TARGET prefix in * executables)
- comms/gnuradio
- science/abinit
- science/elmer-fem
- science/elmer-matc
- science/elmer-meshgen2d
- science/elmerfront
- science/elmerpost
= use x86_64 as ARCH
- devel/g-wrap
= other changes
- print/magicfilter
GNU_CONFIGURE -> HAS_CONFIGURE since it's not generated by autoconf
Total # of ports modified: 1,027
Total # of ports affected: ~7,000 (set GNU_CONFIGURE to yes)
PR: 126524 (obsoletes 52917)
Submitted by: rafan
Tested on: two pointyhat 7-amd64 exp runs (by pav)
Approved by: portmgr (pav)
supports them. This is determined by running ``configure --help'' in
do-configure target and set the shell variable _LATE_CONFIGURE_ARGS
which is then passed to CONFIGURE_ARGS.
- Remove --mandir and --infodir in ports' Makefile where applicable
Few ports use REINPLACE_CMD to achieve the same effect, remove them too.
- Correct some manual pages location from PREFIX/man to MANPREFIX/man
- Define INFO_PATH where necessary
- Document that .info files are installed in a subdirectory relative to
PREFIX/INFO_PATH and slightly change add-plist-info to use INFO_PATH and
subdirectory detection.
PR: ports/111470
Approved by: portmgr
Discussed with: stas (Mk/*), gerald (info related stuffs)
Tested by: pointyhat exp run
We have not checked for this KEYWORD for a long time now, so this
is a complete noop, and thus no PORTREVISION bump. Removing it at
this point is mostly for pedantic reasons, and partly to avoid
perpetuating this anachronism by copy and paste to future scripts.
base rcorder, hard coded variable values in these scripts
are overriding the values in /etc/rc.conf[.local] (due to
the way that variables from the latter are read at boot time).
Therefore, change the boot scripts to set default values only
if the variable is unset in /etc/rc.conf[.local]. This will
allow the service to start at boot time if it's been enabled
as the user would expect.
This change will be a noop for users who have systems that
have not yet been upgraded to the new rc.d code in the base.
In many cases there are other variables in the scripts that
should get similar treatment, however I did not change
anything other than the _enable lines. I'll leave the rest
up to the maintainers to do as they see fit.
Bump PORTREVISION to make sure that users and packages
pick up this change.
