This is an excerpt of what you can see with the standalone "system".
-- Jörg
1. This looks like PC, but where is DOS? How to get pcemu really running
Pcemu is an emulator that emulates an 8086 CPU as well as a bunch of
PC BIOS services, so it basically provides the functionality like an
old PC/XT. Anyway, as with the XT too, the emulator requires something
like an operating system to run with. Since we cannot ship MS-DOS or
one of its variants along with this distribution (for legal reasons),
you're now actually looking at a (sort of) "standalone operating system",
just to get pcemu booted and running. All this system does is show
you this introduction.
You will have to replace this mini-system by a physical image of a
DOS boot floppy. The "system" currently running is booted from the
file
/usr/local/lib/pcemu/DriveA.
It pretends to be the image of a 720 KB diskette, which has been
chosen as the default bootfile size.
In order to obtain the image of a bootable DOS floppy, do the following:
Prepare a 720 KB floppy with a DOS system as you'd like
to run it later. Include all the good stuff you don't want
to miss there. Don't forget to put a simple text editor
there, so you can modify your configuration files later.
Put a copy of the file
/usr/local/lib/pcemu/C/emufs.sys
onto this diskette, and include a line like
device = a:\emufs.sys /usr/local/lib/pcemu/C
into the config.sys file on this diskette. This will
provide you with an interface to the BSD file system from
within your DOS session. (It actually pretends to be a
network drive.) According to David Hedley, you are also
advised to include the line
stacks = 9, 512
there to avoid stack overflow problems with the emulator.
If you want to retain a copy of the standalone "system" you
are currently looking at, move it away:
# cd /usr/local/lib/pcemu; mv DriveA StandaloneA
Now, make a copy of your disk by either:
- under BSD, perform a
# cp /dev/fd0.720 /usr/local/lib/pcemu/DriveA
(the number after the fd may vary for drives other than
the primary one), or
- under DOS, copy the file
/usr/local/lib/pcemu/C/dumpdisk.exe
to your DOS system and execute it. This will dump the
physical copy of either drive A or B to the file drivea
in your current (DOS) working directory. You can then move
this file to
/usr/local/lib/pcemu/DriveA
in your BSD system.
Since pcemu needs to display the standard VGA font, you further need
to tell your X server about the location of the font file. It has
been put under
/usr/local/lib/pcemu/font/
along with the necessary information for the X server. All you need
to do is to tell your X server about it. This can either be done
as a server default by including the directory into the FontPath
section of your XF86Config file (this is for XFree86, refer to
the documentation if you're using another X server). Alternatively,
you can run the command
$ xset fp+ /usr/local/lib/pcemu/font
when X11 is running to instruct your X server to append this directory
to the font path. Should you wish to run pcemu across the network,
remember that the fonts must be physically available at the server
side, or you need to provide an X11 font server (xfs). Refer to
the X11 documentation on how to setup this.
That's all, now you should be able to run pcemu. Add required
device = a:\emufs.sys /... lines to your config.sys as you
need them. It's not wise to make the whole BSD hierarchy available
since DOS does not provide multiuser protection.
Should you wish to override some of the emulator defaults like
size and location of the bootfile, you can do this by settig up a
$HOME/.pcemurc file. Refer to sections 2. and 3. below.
2. Information about this FreeBSD port
This `port' of pcemu to FreeBSD has been prepared by Jörg Wunsch. It
is a modified version of David's code, a few problems have been fixed
for the BSD compilation environment, the location of the default boot
file has been moved in order to get you started with just what you are
reading now. Unfortunately David is no longer developing pcemu, so
during the past years, a number of improvements have been added to the
FreeBSD port. Thanks to Arne Henrik Juul <arnej@math.ntnu.no> who
submitted a large patchset, among them fixes to make harddisk access
work.
The PostScript document David is mentioning under 3. below has
been compressed and stored under
/usr/local/lib/pcemu/doc/report.ps.gz.
It is huge however, so if you don't care much for it you might wish
to remove it later.
Since i'm living in Germany with a German keyboard, i found the
original X11 KeySym to PC scancode translation unacceptable. Several
scancodes have been unreachable for me. Hence i decided to add another
section to the .pcemurc file allowing to instruct pcemu of specific
keyboard layout semantics. They consist of the keyword keymap,
followed by the desired PC scancode, an equal sign, and the character
that is generated for this key under X11 without any shift keys. (Note
that no space is allowed on either side of the equal sign.) This way
i won't get a German key mapping under DOS, but at least a valid keyboard
layout where all the scan codes can actually be generated at all.
The appropriate section of my .pcemurc file looks like:
keymap 12=ß
keymap 13='
keymap 21=z
keymap 26=]
keymap 27=+
keymap 39=\
keymap 40=[
keymap 41=^
keymap 43=#
keymap 44=y
keymap 53=-
keymap 86=<
Another recent addition to the .pcemurc file was the option to add
floppy and hard disk defintions dynamically. (Previously, everything
needed to be compiled into the emulator.) The syntax of those entries
is:
keyword filename sectors cylinders heads
Examples:
floppydisk /dev/rfd0 18 80 2
harddisk /dev/rad0 255 400 63
Drive letters are being assigned in ascending order, where drive A: is
always reserved for the boot file. Write permission to the file in
question is required by the time pcemu is being started (i. e. any
floppy media need to be in the drive by that time). Be careful with
letting DOS tools access your hard disks...
Should you wish to contact me regarding this FreeBSD port, you can
reach me as joerg_wunsch@uriah.heep.sax.de.
3e4ed01146