448 lines
15 KiB
Text
448 lines
15 KiB
Text
; ========================================
|
|
; PTPDv2 version 2.3.0-svn default configuration
|
|
; ========================================
|
|
|
|
; NOTE: the following settings are affected by ptpengine:preset selection:
|
|
; ptpengine:slave_only
|
|
; clock:no_adjust
|
|
; ptpengine:clock_class - allowed range and default value
|
|
; To see all preset settings, run ptpd2 -H (--long-help)
|
|
|
|
; Network interface to use (required)
|
|
ptpengine:interface = igb0
|
|
|
|
; PTP engine preset:
|
|
; none = Defaults, no clock class restrictions
|
|
; slaveonly = Slave only (clock class 255 only)
|
|
; masteronly = Master, passive when not best master (clock class 0..127)
|
|
; masterslave = Full IEEE 1588 implementation:
|
|
; Master, slave when not best master
|
|
; (clock class 128..254)
|
|
;
|
|
; Options: none slaveonly masteronly masterslave
|
|
ptpengine:preset = slaveonly
|
|
|
|
; IP transmission mode (requires IP transport) - hybrid mode uses
|
|
; multicast for sync and announce, and unicast for delay request /
|
|
; response
|
|
; Options: multicast unicast hybrid
|
|
ptpengine:ip_mode = multicast
|
|
|
|
; Transport type for PTP packets
|
|
; Options: ipv4 ethernet
|
|
ptpengine:transport = ipv4
|
|
|
|
; Use libpcap for sending and receiving traffic (automatically enabled
|
|
; in Ethernet mode)
|
|
ptpengine:use_libpcap = N
|
|
|
|
; Delay detection mode used - use DELAY_DISABLED for syntonisation
|
|
; only (no synchronisation)
|
|
; Options: E2E P2P DELAY_DISABLED
|
|
ptpengine:delay_mechanism = E2E
|
|
|
|
; PTP domain number
|
|
ptpengine:domain = 0
|
|
|
|
; Slave only mode (if set, overrides preset setting and sets clock class to 255)
|
|
ptpengine:slave_only = Y
|
|
|
|
; Specify latency correction for incoming packets
|
|
ptpengine:inbound_latency = 0
|
|
|
|
; Specify latency correction for outgoing packets
|
|
ptpengine:outbound_latency = 0
|
|
|
|
; Compatibility option: In slave state, always respect UTC offset
|
|
; announced by best master, even if the the
|
|
; currrentUtcOffsetValid flag is announced FALSE
|
|
ptpengine:always_respect_utc_offset = N
|
|
|
|
; PTP announce message interval in master state (expressed as log 2
|
|
; i.e. -1=0.5s, 0=1s, 1=2s etc.)
|
|
ptpengine:log_announce_interval = 1
|
|
|
|
; PTP announce receipt timeout announced in master state
|
|
ptpengine:announce_timeout = 6
|
|
|
|
; PTP announce receipt timeout grace period in slave state:
|
|
; when announce receipt timeout occurs, disqualify current best GM,
|
|
; then wait n times announce receipt timeout before resetting.
|
|
; Allows for a seamless GM failover when standby GMs are slow to react.
|
|
; When set to 0, this option is not used.
|
|
ptpengine:announce_timeout_grace_period = 0
|
|
|
|
; PTP sync message interval in master state (expressed as log 2
|
|
; i.e. -1=0.5s, 0=1s, 1=2s etc.)
|
|
ptpengine:log_sync_interval = 0
|
|
|
|
; Initial delay request message interval for slave mode, before first
|
|
; delay response is received (expressed as log 2 i.e. -1=0.5s, 0=1s,
|
|
; 1=2s etc.)
|
|
ptpengine:log_delayreq_interval_initial = 0
|
|
|
|
; Minimum delay request message interval in master state, in slave
|
|
; mode overrides the master interval, required in hybrid mode
|
|
; (expressed as log 2 i.e. -1=0.5s, 0=1s, 1=2s etc.)
|
|
ptpengine:log_delayreq_interval = 0
|
|
|
|
; Minimum peer delay request message interval in master state.
|
|
; (expressed as log 2 i.e. -1=0.5s, 0=1s, 1=2s etc.)
|
|
ptpengine:log_peer_delayreq_interval = 1
|
|
|
|
; Maximum number of foreign masters (foreign master record size
|
|
; allocated at startup)
|
|
|
|
ptpengine:foreignrecord_capacity = 5
|
|
|
|
; Specify Allan variance announced in master state
|
|
ptpengine:ptp_allan_variance = 28768
|
|
|
|
; Clock accuracy range announced in master state
|
|
; Options: ACC_25NS ACC_100NS ACC_250NS ACC_1US ACC_2.5US ACC_10US
|
|
; ACC_25US ACC_100US ACC_250US ACC_1MS ACC_2.5MS ACC_10MS ACC_25MS
|
|
; ACC_100MS ACC_250MS ACC_1S ACC_10S ACC_10SPLUS ACC_UNKNOWN
|
|
ptpengine:ptp_clock_accuracy = ACC_UNKNOWN
|
|
|
|
; underlying time source UTC offset announced in master state
|
|
ptpengine:utc_offset = 0
|
|
|
|
; underlying time source UTC offset validity announced in master state
|
|
ptpengine:utc_offset_valid = N
|
|
|
|
; underlying time source time traceability announced in master state
|
|
ptpengine:time_traceable = N
|
|
|
|
; underlying time source frequency traceability announced in master state
|
|
ptpengine:frequency_traceable = N
|
|
|
|
; Time scale announced in master state (with ARB timescale, UTC
|
|
; properties are ignored by slaves), when clock class 13 (application
|
|
; specific), this value is ignored and ARB is used.
|
|
; Options: PTP ARB
|
|
ptpengine:ptp_timescale = ARB
|
|
|
|
; Time source announced in master state
|
|
; Options: ATOMIC_CLOCK GPS TERRESTRIAL_RADIO PTP NTP HAND_SET OTHER
|
|
; INTERNAL_OSCILLATOR
|
|
ptpengine:ptp_timesource = INTERNAL_OSCILLATOR
|
|
|
|
; Clock class - announced in master state. Always 255 for slave-only mode.
|
|
; Minimum, maximum and default values are controlled by presets.
|
|
; If set to 13 (application specific time source), announced
|
|
; time scale is always set to ARB. This setting controls the
|
|
; states a PTP port can be in. If below 128, port will only
|
|
; be in MASTER or PASSIVE states (master only). If above 127,
|
|
; port will be in MASTER or SLAVE states.
|
|
ptpengine:clock_class = 255
|
|
|
|
; Priority 1 value announced in master state and used for Best Master
|
|
; Clock selection
|
|
ptpengine:priority1 = 128
|
|
|
|
; Priority 2 value announced in master state and used for Best Master
|
|
; Clock selection
|
|
ptpengine:priority2 = 128
|
|
|
|
; Specify unicast destination for unicast master mode (in unicast
|
|
; slave mode overrides delay request destination)
|
|
ptpengine:unicast_address =
|
|
|
|
; Send explicit IGMP joins between servo resets
|
|
ptpengine:igmp_refresh = Y
|
|
|
|
; Multicast time to live for multicast PTP packets (ignored and set to
|
|
; 1 for peer to peer messages)
|
|
ptpengine:multicast_ttl = 16
|
|
|
|
; DiffServ CodepPoint for packet prioritisation (decimal). When set to
|
|
; zero, this option is not used.
|
|
; 46 = Expedited Forwarding (0x2e)
|
|
ptpengine:ip_dscp = 0
|
|
|
|
; Use PTP alternative multicast group like PTPv1 (if compiled with
|
|
; PTPD_EXPERIMENTAL):
|
|
; 0 = 224.0.1.129, 1 = 224.0.1.130, 2 = 224.0.1.131, 3 = 224.0.1.132
|
|
ptpengine:alt_mcast_group = 0
|
|
|
|
; Enable outlier filter for the Delay Response component in slave state
|
|
ptpengine:delay_outlier_filter_enable = Y
|
|
|
|
; Delay Response outlier filter action. If set to 'filter', outliers
|
|
; are replaced with moving average
|
|
; Options: discard filter
|
|
ptpengine:delay_outlier_filter_action = filter
|
|
|
|
; Number of samples in the Delay Response outlier filter buffer
|
|
ptpengine:delay_outlier_filter_capacity = 20
|
|
|
|
; Delay Response outlier filter threshold: multiplier for the Peirce's
|
|
; maximum standard deviation. When set below 1.0, filter is tighter,
|
|
; when set above 1.0, filter is looser than standard Peirce's test.
|
|
ptpengine:delay_outlier_filter_threshold = 1.000000
|
|
|
|
; Delay Response outlier weight: if an outlier is detected, this value
|
|
; determines the amount of its deviation from mean that is used to
|
|
; build the standard deviation statistics and influence further
|
|
; outlier detection.
|
|
; When set to 1.0, the outlier is used as is.
|
|
;
|
|
ptpengine:delay_outlier_weight = 1.000000
|
|
|
|
; Enable outlier filter for the Sync component in slave state
|
|
ptpengine:sync_outlier_filter_enable = N
|
|
|
|
; Sync outlier filter action. If set to 'filter', outliers are
|
|
; replaced with moving average
|
|
; Options: discard filter
|
|
ptpengine:sync_outlier_filter_action = filter
|
|
|
|
; Number of samples in the Sync outlier filter buffer
|
|
ptpengine:sync_outlier_filter_capacity = 20
|
|
|
|
; Sync outlier filter threshold: multiplier for the Peirce's maximum
|
|
; standard deviation. When set below 1.0, filter is tighter, when set
|
|
; above 1.0, filter is looser than standard Peirce's test.
|
|
ptpengine:sync_outlier_filter_threshold = 1.000000
|
|
|
|
; Sync outlier weight: if an outlier is detected, this value
|
|
; determines the amount of its deviation from mean that is used to
|
|
; build the standard deviation statistics and influence further
|
|
; outlier detection. When set to 1.0, the outlier is used as is.
|
|
ptpengine:sync_outlier_weight = 1.000000
|
|
|
|
; Delay between moving to slave state and enabling clock updates
|
|
; expressed as number of statistics update periods (see
|
|
; global:statistics_update_interval). This allows one-way delay to
|
|
; stabilise before starting clock updates. Activated when going into
|
|
; slave state and during GM failover in slave state.
|
|
; 0 - not used.
|
|
ptpengine:calibration_delay = 0
|
|
|
|
; Enable panic mode: when offset from master is above 1 second, stop
|
|
; updating the clock for a period of time and then step the clock if
|
|
; offset remains above 1 second.
|
|
ptpengine:panic_mode = Y
|
|
|
|
; Duration of the panic mode period (no clock updates) when offset
|
|
; above 1 second detected
|
|
ptpengine:panic_mode_duration = 2
|
|
|
|
; Use JobID (PID) for UUID
|
|
ptpengine:pid_as_clock_idendity = N
|
|
|
|
; Fail over to NTP when PTP time sync not available - requires
|
|
; ntpengine:enabled but does not require the rest of NTP configuration
|
|
; - will warn instead of failing over if cannot control ntpd.
|
|
ptpengine:ntp_failover = N
|
|
|
|
; NTP failover timeout in seconds: time between PTP slave going into
|
|
; LISTENING state, and failing over to NTP. 0 = fail over immediately.
|
|
ptpengine:ntp_failover_timeout = 60
|
|
|
|
; Prefer NTP time synchronisation when not controlling the clock (all
|
|
; states, including slave when clock:no_adjust set)
|
|
ptpengine:prefer_ntp = N
|
|
|
|
; When entering panic mode, fail over to NTP (after the NTP failover
|
|
; timeout period) - requires ntpengine:enabled but does not require
|
|
; the rest of NTP configuration - will warn instead of failing over if
|
|
; it cannot control ntpd.
|
|
ptpengine:panic_mode_ntp = N
|
|
|
|
; Do not adjust the clock
|
|
clock:no_adjust = N
|
|
|
|
; Do not reset the clock - only slew
|
|
clock:no_reset = N
|
|
|
|
; Observed drift handling method between servo restarts:
|
|
; reset: set to zero (not recommended)
|
|
; preserve: use kernel value,
|
|
; file: load and save to drift file on startup/shutdown, use kernel
|
|
; value inbetween.
|
|
; To specify drift file, use the clock:drift_file setting.
|
|
; Options: reset preserve file
|
|
clock:drift_handling = preserve
|
|
|
|
; Specify drift file
|
|
clock:drift_file = /etc/ptpd2_kernelclock.drift
|
|
|
|
; Maximum absolute frequency shift which can be applied to the clock servo
|
|
; when slewing the clock. Expressed in parts per million (1 ppm = shift of
|
|
; 1 us per second. Values above 512 will use the tick duration correction
|
|
; to allow even faster slewing. Default maximum is 512 without using tick.
|
|
clock:max_offset_ppm = 500
|
|
|
|
; One-way delay filter stiffness
|
|
servo:delayfilter_stiffness = 6
|
|
|
|
; Clock servo PI controller proportional component gain (kP)
|
|
servo:kp = 0.1
|
|
|
|
; Clock servo PI controller integral component gain (kI)
|
|
servo:ki = 0.001
|
|
|
|
; Maximum accepted delayMS value in nanoseconds (Sync).
|
|
; 0 = not checked.
|
|
servo:max_delay = 10000000
|
|
|
|
; Enable clock synchronisation servo stability detection
|
|
; (based on standard deviation of the observed drift value)
|
|
; - drift will be saved to drift file / cached when considered stable,
|
|
; also clock stability status will be logged
|
|
;
|
|
servo:stability_detection = N
|
|
|
|
; Specify the observed drift standard deviation threshold in parts per billion
|
|
; (ppb) - if stanard deviation is within the threshold, servo is considered
|
|
; stable.
|
|
servo:stability_threshold = 5.000000
|
|
|
|
; Specify for how many statistics update intervals the observed drift standard
|
|
; deviation has to stay within threshold to be considered stable
|
|
;
|
|
servo:stability_period = 3
|
|
|
|
; Specify after how many minutes without stabilisation servo is considered
|
|
; unstable. Assists with logging servo stability information and
|
|
; allows to preserve observed drift if servo cannot stabilise.
|
|
;
|
|
servo:stability_timeout = 10
|
|
|
|
; Do not reset the clock if offset from master is greater
|
|
; than this value (nanoseconds). 0 = not used.
|
|
servo:max_offset = 10000000
|
|
|
|
; Send log messages to syslog. Disabling this
|
|
; sends all messages to stdout (or speficied log file)
|
|
global:use_syslog = N
|
|
|
|
; Lock file location
|
|
global:lock_file =
|
|
|
|
; Use mode specific and interface specific lock files (overrides
|
|
; global:lock_file)
|
|
global:auto_lockfile = N
|
|
|
|
; Lock file directory: used with automatic mode-specific lock files,
|
|
; also used when no lock file is specified. When lock file
|
|
; is specified, it's expected to be an absolute path.
|
|
global:lock_directory = /var/run
|
|
|
|
; Skip lock file checking and locking
|
|
global:ignore_lock = N
|
|
|
|
; File used to record data about sync packets. Setting this enables recording.
|
|
global:quality_file = /usr/scratch/log/ptpd.quality
|
|
|
|
; Maximum sync packet record file size (in kB) - file will be
|
|
; truncated if size exceeds the limit.
|
|
; 0 - no limit.
|
|
global:quality_file_max_size = 0
|
|
|
|
; Enable log rotation of the sync packet record file up to n files.
|
|
; 0 - do not rotate.
|
|
global:quality_file_max_files = 0
|
|
|
|
; Truncate the sync packet record file every time it is (re) opened -
|
|
; on startup and SIGHUP
|
|
global:quality_file_truncate = N
|
|
|
|
; File used to log ptpd2 status information
|
|
global:status_file = /usr/scratch/log/ptpd2.status.log
|
|
|
|
; Enable / disable writing status information to file
|
|
global:log_status = Y
|
|
|
|
; Status file update interval in seconds
|
|
;
|
|
global:status_update_interval = 1
|
|
|
|
; Specify log file path (event log). Setting this enables logging to file.
|
|
global:log_file = /usr/scratch/log/ptpd2.status.log
|
|
|
|
; Maximum log file size (in kB) - log file will be truncated if size
|
|
; exceeds the limit.
|
|
; 0 - no limit.
|
|
global:log_file_max_size = 0
|
|
|
|
; Enable log rotation of the sync packet record file up to n files.
|
|
; 0 - do not rotate
|
|
global:log_file_max_files = 0
|
|
|
|
; Truncate the log file every time it is (re) opened - on startup and SIGHUP
|
|
global:log_file_truncate = N
|
|
|
|
; Specify log level (only messages of the specified priority or higer
|
|
; will be logged).
|
|
; The minimal level is LOG_ERR. LOG_ALL enables debug output if compiled with
|
|
; RUNTIME_DEBUG
|
|
; Options: LOG_ERR LOG_WARNING LOG_NOTICE LOG_INFO LOG_ALL
|
|
global:log_level = LOG_ALL
|
|
|
|
; Specify statistics log file path. Setting this enables logging of
|
|
; statistics but can be overriden with global:log_statistics
|
|
global:statistics_file = /usr/scratch/log/ptpd.log
|
|
|
|
; Log timing statistics every n seconds for Sync and Delay Response
|
|
; messages (0 - log all)
|
|
global:statistics_log_interval = 0
|
|
|
|
; Maximum statistics log file size (in kB) - log file will be
|
|
; truncated if size exceeds the limit.
|
|
; 0 - no limit.
|
|
global:statistics_file_max_size = 0
|
|
|
|
; Enable log rotation of the statistics file up to n files. 0 - do not rotate
|
|
;
|
|
global:statistics_file_max_files = 0
|
|
|
|
; Truncate the statistics file every time it is (re) opened - on
|
|
; startup and SIGHUP
|
|
global:statistics_file_truncate = N
|
|
|
|
; Dump the contents of every PTP packet
|
|
global:dump_packets = N
|
|
|
|
; Run in foreground with statistics and all messages logged to stdout.
|
|
; Overrides log file and statistics file settings and disables syslog.
|
|
;
|
|
global:verbose_foreground = N
|
|
|
|
; Run in foreground
|
|
global:foreground = N
|
|
|
|
; Log timing statistics for every PTP packet received
|
|
global:log_statistics = Y
|
|
|
|
; Linux only: bind ptpd2 process to a selected CPU core number.
|
|
; 0 = first CPU core, etc. -1 = do not bind to a single core.
|
|
global:cpuaffinity_cpucore = -1
|
|
|
|
; Clock synchronisation statistics update interval in seconds
|
|
;
|
|
global:statistics_update_interval = 5
|
|
|
|
; Enable NTPd integration
|
|
ntpengine:enabled = N
|
|
|
|
; Enable control over local NTPd daemon
|
|
ntpengine:control_enabled = N
|
|
|
|
; NTP control check interval in seconds
|
|
;
|
|
ntpengine:check_interval = 15
|
|
|
|
; NTP key number - must be configured as a trusted control key in ntp.conf,
|
|
; and must be non-zero for the ntpengine:control_enabled setting to take effect.
|
|
;
|
|
ntpengine:key_id = 0
|
|
|
|
; NTP key (plain text, max. 20 characters) - must match the key
|
|
; configured in ntpd's keys file, and must be non-zero for the
|
|
; ntpengine:control_enabled setting to take effect.
|
|
ntpengine:key =
|
|
|
|
; ========= newline required in the end ==========
|
|
|