kpriv/linux-hardened
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
linux-hardened/drivers/net/ll_temac_main.c

1114 lines
28 KiB
C
Raw Normal View History

net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
/*
* Driver for Xilinx TEMAC Ethernet device
*
* Copyright (c) 2008 Nissin Systems Co., Ltd., Yoshio Kashiwagi
* Copyright (c) 2005-2008 DLA Systems, David H. Lynch Jr. <dhlii@dlasys.net>
* Copyright (c) 2008-2009 Secret Lab Technologies Ltd.
*
* This is a driver for the Xilinx ll_temac ipcore which is often used
* in the Virtex and Spartan series of chips.
*
* Notes:
* - The ll_temac hardware uses indirect access for many of the TEMAC
* registers, include the MDIO bus. However, indirect access to MDIO
* registers take considerably more clock cycles than to TEMAC registers.
* MDIO accesses are long, so threads doing them should probably sleep
* rather than busywait. However, since only one indirect access can be
* in progress at any given time, that means that *all* indirect accesses
* could end up sleeping (to wait for an MDIO access to complete).
* Fortunately none of the indirect accesses are on the 'hot' path for tx
* or rx, so this should be okay.
*
* TODO:
* - Factor out locallink DMA code into separate driver
* - Fix multicast assignment.
* - Fix support for hardware checksumming.
* - Testing. Lots and lots of testing.
*
*/
#include <linux/delay.h>
#include <linux/etherdevice.h>
#include <linux/init.h>
#include <linux/mii.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/netdevice.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/of_mdio.h>
#include <linux/of_platform.h>
#include <linux/skbuff.h>
#include <linux/spinlock.h>
#include <linux/tcp.h> /* needed for sizeof(tcphdr) */
#include <linux/udp.h> /* needed for sizeof(udphdr) */
#include <linux/phy.h>
#include <linux/in.h>
#include <linux/io.h>
#include <linux/ip.h>
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 09:04:11 +01:00
#include <linux/slab.h>
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
#include "ll_temac.h"
#define TX_BD_NUM 64
#define RX_BD_NUM 128
/* ---------------------------------------------------------------------
* Low level register access functions
*/
u32 temac_ior(struct temac_local *lp, int offset)
{
return in_be32((u32 *)(lp->regs + offset));
}
void temac_iow(struct temac_local *lp, int offset, u32 value)
{
out_be32((u32 *) (lp->regs + offset), value);
}
int temac_indirect_busywait(struct temac_local *lp)
{
long end = jiffies + 2;
while (!(temac_ior(lp, XTE_RDY0_OFFSET) & XTE_RDY0_HARD_ACS_RDY_MASK)) {
if (end - jiffies <= 0) {
WARN_ON(1);
return -ETIMEDOUT;
}
msleep(1);
}
return 0;
}
/**
* temac_indirect_in32
*
* lp->indirect_mutex must be held when calling this function
*/
u32 temac_indirect_in32(struct temac_local *lp, int reg)
{
u32 val;
if (temac_indirect_busywait(lp))
return -ETIMEDOUT;
temac_iow(lp, XTE_CTL0_OFFSET, reg);
if (temac_indirect_busywait(lp))
return -ETIMEDOUT;
val = temac_ior(lp, XTE_LSW0_OFFSET);
return val;
}
/**
* temac_indirect_out32
*
* lp->indirect_mutex must be held when calling this function
*/
void temac_indirect_out32(struct temac_local *lp, int reg, u32 value)
{
if (temac_indirect_busywait(lp))
return;
temac_iow(lp, XTE_LSW0_OFFSET, value);
temac_iow(lp, XTE_CTL0_OFFSET, CNTLREG_WRITE_ENABLE_MASK | reg);
}
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
/**
* temac_dma_in32 - Memory mapped DMA read, this function expects a
* register input that is based on DCR word addresses which
* are then converted to memory mapped byte addresses
*/
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
static u32 temac_dma_in32(struct temac_local *lp, int reg)
{
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
return in_be32((u32 *)(lp->sdma_regs + (reg << 2)));
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
/**
* temac_dma_out32 - Memory mapped DMA read, this function expects a
* register input that is based on DCR word addresses which
* are then converted to memory mapped byte addresses
*/
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
static void temac_dma_out32(struct temac_local *lp, int reg, u32 value)
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
{
out_be32((u32 *)(lp->sdma_regs + (reg << 2)), value);
}
/* DMA register access functions can be DCR based or memory mapped.
* The PowerPC 440 is DCR based, the PowerPC 405 and MicroBlaze are both
* memory mapped.
*/
#ifdef CONFIG_PPC_DCR
/**
* temac_dma_dcr_in32 - DCR based DMA read
*/
static u32 temac_dma_dcr_in(struct temac_local *lp, int reg)
{
return dcr_read(lp->sdma_dcrs, reg);
}
/**
* temac_dma_dcr_out32 - DCR based DMA write
*/
static void temac_dma_dcr_out(struct temac_local *lp, int reg, u32 value)
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
{
dcr_write(lp->sdma_dcrs, reg, value);
}
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
/**
* temac_dcr_setup - If the DMA is DCR based, then setup the address and
* I/O functions
*/
static int temac_dcr_setup(struct temac_local *lp, struct of_device *op,
struct device_node *np)
{
unsigned int dcrs;
/* setup the dcr address mapping if it's in the device tree */
dcrs = dcr_resource_start(np, 0);
if (dcrs != 0) {
lp->sdma_dcrs = dcr_map(np, dcrs, dcr_resource_len(np, 0));
lp->dma_in = temac_dma_dcr_in;
lp->dma_out = temac_dma_dcr_out;
dev_dbg(&op->dev, "DCR base: %x\n", dcrs);
return 0;
}
/* no DCR in the device tree, indicate a failure */
return -1;
}
#else
/*
* temac_dcr_setup - This is a stub for when DCR is not supported,
* such as with MicroBlaze
*/
static int temac_dcr_setup(struct temac_local *lp, struct of_device *op,
struct device_node *np)
{
return -1;
}
#endif
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
/**
* temac_dma_bd_init - Setup buffer descriptor rings
*/
static int temac_dma_bd_init(struct net_device *ndev)
{
struct temac_local *lp = netdev_priv(ndev);
struct sk_buff *skb;
int i;
drivers/net : Correct the size argument to kzalloc lp->rx_skb has type struct sk_buff **, not struct sk_buff *, so the elements of the array should have pointer type, not structure type. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @disable sizeof_type_expr@ type T; T **x; @@ x = <+...sizeof( - T + *x )...+> // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29 10:15:42 +01:00
lp->rx_skb = kzalloc(sizeof(*lp->rx_skb) * RX_BD_NUM, GFP_KERNEL);
ll_temac: add error checking to DMA init path Add error checking to DMA descriptor rings initialization code. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-01 01:39:05 +02:00
if (!lp->rx_skb) {
dev_err(&ndev->dev,
"can't allocate memory for DMA RX buffer\n");
goto out;
}
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
/* allocate the tx and rx ring buffer descriptors. */
/* returns a virtual addres and a physical address. */
lp->tx_bd_v = dma_alloc_coherent(ndev->dev.parent,
sizeof(*lp->tx_bd_v) * TX_BD_NUM,
&lp->tx_bd_p, GFP_KERNEL);
ll_temac: add error checking to DMA init path Add error checking to DMA descriptor rings initialization code. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-01 01:39:05 +02:00
if (!lp->tx_bd_v) {
dev_err(&ndev->dev,
"unable to allocate DMA TX buffer descriptors");
goto out;
}
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
lp->rx_bd_v = dma_alloc_coherent(ndev->dev.parent,
sizeof(*lp->rx_bd_v) * RX_BD_NUM,
&lp->rx_bd_p, GFP_KERNEL);
ll_temac: add error checking to DMA init path Add error checking to DMA descriptor rings initialization code. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-01 01:39:05 +02:00
if (!lp->rx_bd_v) {
dev_err(&ndev->dev,
"unable to allocate DMA RX buffer descriptors");
goto out;
}
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
memset(lp->tx_bd_v, 0, sizeof(*lp->tx_bd_v) * TX_BD_NUM);
for (i = 0; i < TX_BD_NUM; i++) {
lp->tx_bd_v[i].next = lp->tx_bd_p +
sizeof(*lp->tx_bd_v) * ((i + 1) % TX_BD_NUM);
}
memset(lp->rx_bd_v, 0, sizeof(*lp->rx_bd_v) * RX_BD_NUM);
for (i = 0; i < RX_BD_NUM; i++) {
lp->rx_bd_v[i].next = lp->rx_bd_p +
sizeof(*lp->rx_bd_v) * ((i + 1) % RX_BD_NUM);
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
skb = netdev_alloc_skb_ip_align(ndev,
XTE_MAX_JUMBO_FRAME_SIZE);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if (skb == 0) {
dev_err(&ndev->dev, "alloc_skb error %d\n", i);
ll_temac: add error checking to DMA init path Add error checking to DMA descriptor rings initialization code. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-01 01:39:05 +02:00
goto out;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
lp->rx_skb[i] = skb;
/* returns physical address of skb->data */
lp->rx_bd_v[i].phys = dma_map_single(ndev->dev.parent,
skb->data,
XTE_MAX_JUMBO_FRAME_SIZE,
DMA_FROM_DEVICE);
lp->rx_bd_v[i].len = XTE_MAX_JUMBO_FRAME_SIZE;
lp->rx_bd_v[i].app0 = STS_CTRL_APP0_IRQONEND;
}
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
lp->dma_out(lp, TX_CHNL_CTRL, 0x10220400 |
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
CHNL_CTRL_IRQ_EN |
CHNL_CTRL_IRQ_DLY_EN |
CHNL_CTRL_IRQ_COAL_EN);
/* 0x10220483 */
/* 0x00100483 */
net: ll_temac: fix checksum offload logic The current checksum offload code does not work and this corrects that functionality. It also updates the interrupt coallescing initialization so than there are fewer interrupts and performance is increased. Signed-off-by: Brian Hill <brian.hill@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-27 05:44:30 +02:00
lp->dma_out(lp, RX_CHNL_CTRL, 0xff070000 |
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
CHNL_CTRL_IRQ_EN |
CHNL_CTRL_IRQ_DLY_EN |
CHNL_CTRL_IRQ_COAL_EN |
CHNL_CTRL_IRQ_IOE);
/* 0xff010283 */
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
lp->dma_out(lp, RX_CURDESC_PTR, lp->rx_bd_p);
lp->dma_out(lp, RX_TAILDESC_PTR,
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
lp->rx_bd_p + (sizeof(*lp->rx_bd_v) * (RX_BD_NUM - 1)));
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
lp->dma_out(lp, TX_CURDESC_PTR, lp->tx_bd_p);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
return 0;
ll_temac: add error checking to DMA init path Add error checking to DMA descriptor rings initialization code. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-01 01:39:05 +02:00
out:
return -ENOMEM;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
/* ---------------------------------------------------------------------
* net_device_ops
*/
static int temac_set_mac_address(struct net_device *ndev, void *address)
{
struct temac_local *lp = netdev_priv(ndev);
if (address)
memcpy(ndev->dev_addr, address, ETH_ALEN);
if (!is_valid_ether_addr(ndev->dev_addr))
random_ether_addr(ndev->dev_addr);
/* set up unicast MAC address filter set its mac address */
mutex_lock(&lp->indirect_mutex);
temac_indirect_out32(lp, XTE_UAW0_OFFSET,
(ndev->dev_addr[0]) |
(ndev->dev_addr[1] << 8) |
(ndev->dev_addr[2] << 16) |
(ndev->dev_addr[3] << 24));
/* There are reserved bits in EUAW1
* so don't affect them Set MAC bits [47:32] in EUAW1 */
temac_indirect_out32(lp, XTE_UAW1_OFFSET,
(ndev->dev_addr[4] & 0x000000ff) |
(ndev->dev_addr[5] << 8));
mutex_unlock(&lp->indirect_mutex);
return 0;
}
ll_temac: Fix MAC address configuration from userland A userland command to set the LLTEMAC MAC address, i.e. "ifconfig eth0 hw addr xx:yy:zz:pp:dd:qq", results in a device address of 00:01:xx:yy:zz:pp. Correct this. Signed-off-by: Steven J. Magnani <steve@digidescorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-17 08:55:07 +01:00
static int netdev_set_mac_address(struct net_device *ndev, void *p)
{
struct sockaddr *addr = p;
return temac_set_mac_address(ndev, addr->sa_data);
}
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
static void temac_set_multicast_list(struct net_device *ndev)
{
struct temac_local *lp = netdev_priv(ndev);
u32 multi_addr_msw, multi_addr_lsw, val;
int i;
mutex_lock(&lp->indirect_mutex);
drivers/net: Move && and || to end of previous line Only files where David Miller is the primary git-signer. wireless, wimax, ixgbe, etc are not modified. Compile tested x86 allyesconfig only Not all files compiled (not x86 compatible) Added a few > 80 column lines, which I ignored. Existing checkpatch complaints ignored. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 08:58:21 +01:00
if (ndev->flags & (IFF_ALLMULTI | IFF_PROMISC) ||
net: use netdev_mc_count and netdev_mc_empty when appropriate This patch replaces dev->mc_count in all drivers (hopefully I didn't miss anything). Used spatch and did small tweaks and conding style changes when it was suitable. Jirka Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-08 05:30:35 +01:00
netdev_mc_count(ndev) > MULTICAST_CAM_TABLE_NUM) {
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
/*
* We must make the kernel realise we had to move
* into promisc mode or we start all out war on
* the cable. If it was a promisc request the
* flag is already set. If not we assert it.
*/
ndev->flags |= IFF_PROMISC;
temac_indirect_out32(lp, XTE_AFM_OFFSET, XTE_AFM_EPPRM_MASK);
dev_info(&ndev->dev, "Promiscuous mode enabled.\n");
net: use netdev_mc_count and netdev_mc_empty when appropriate This patch replaces dev->mc_count in all drivers (hopefully I didn't miss anything). Used spatch and did small tweaks and conding style changes when it was suitable. Jirka Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-08 05:30:35 +01:00
} else if (!netdev_mc_empty(ndev)) {
net: convert multicast list to list_head Converts the list and the core manipulating with it to be the same as uc_list. +uses two functions for adding/removing mc address (normal and "global" variant) instead of a function parameter. +removes dev_mcast.c completely. +exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for manipulation with lists on a sandbox (used in bonding and 80211 drivers) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-01 23:22:57 +02:00
struct netdev_hw_addr *ha;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
net: convert multiple drivers to use netdev_for_each_mc_addr, part5 V2 removed some needless checks and also corrected bug in lp486e (dmi was passed instead of dmi->dmi_addr) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-23 10:19:49 +01:00
i = 0;
net: convert multicast list to list_head Converts the list and the core manipulating with it to be the same as uc_list. +uses two functions for adding/removing mc address (normal and "global" variant) instead of a function parameter. +removes dev_mcast.c completely. +exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for manipulation with lists on a sandbox (used in bonding and 80211 drivers) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-01 23:22:57 +02:00
netdev_for_each_mc_addr(ha, ndev) {
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if (i >= MULTICAST_CAM_TABLE_NUM)
break;
net: convert multicast list to list_head Converts the list and the core manipulating with it to be the same as uc_list. +uses two functions for adding/removing mc address (normal and "global" variant) instead of a function parameter. +removes dev_mcast.c completely. +exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for manipulation with lists on a sandbox (used in bonding and 80211 drivers) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-01 23:22:57 +02:00
multi_addr_msw = ((ha->addr[3] << 24) |
(ha->addr[2] << 16) |
(ha->addr[1] << 8) |
(ha->addr[0]));
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
temac_indirect_out32(lp, XTE_MAW0_OFFSET,
multi_addr_msw);
net: convert multicast list to list_head Converts the list and the core manipulating with it to be the same as uc_list. +uses two functions for adding/removing mc address (normal and "global" variant) instead of a function parameter. +removes dev_mcast.c completely. +exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for manipulation with lists on a sandbox (used in bonding and 80211 drivers) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-01 23:22:57 +02:00
multi_addr_lsw = ((ha->addr[5] << 8) |
(ha->addr[4]) | (i << 16));
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
temac_indirect_out32(lp, XTE_MAW1_OFFSET,
multi_addr_lsw);
net: convert multiple drivers to use netdev_for_each_mc_addr, part5 V2 removed some needless checks and also corrected bug in lp486e (dmi was passed instead of dmi->dmi_addr) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-23 10:19:49 +01:00
i++;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
} else {
val = temac_indirect_in32(lp, XTE_AFM_OFFSET);
temac_indirect_out32(lp, XTE_AFM_OFFSET,
val & ~XTE_AFM_EPPRM_MASK);
temac_indirect_out32(lp, XTE_MAW0_OFFSET, 0);
temac_indirect_out32(lp, XTE_MAW1_OFFSET, 0);
dev_info(&ndev->dev, "Promiscuous mode disabled.\n");
}
mutex_unlock(&lp->indirect_mutex);
}
struct temac_option {
int flg;
u32 opt;
u32 reg;
u32 m_or;
u32 m_and;
} temac_options[] = {
/* Turn on jumbo packet support for both Rx and Tx */
{
.opt = XTE_OPTION_JUMBO,
.reg = XTE_TXC_OFFSET,
.m_or = XTE_TXC_TXJMBO_MASK,
},
{
.opt = XTE_OPTION_JUMBO,
.reg = XTE_RXC1_OFFSET,
.m_or =XTE_RXC1_RXJMBO_MASK,
},
/* Turn on VLAN packet support for both Rx and Tx */
{
.opt = XTE_OPTION_VLAN,
.reg = XTE_TXC_OFFSET,
.m_or =XTE_TXC_TXVLAN_MASK,
},
{
.opt = XTE_OPTION_VLAN,
.reg = XTE_RXC1_OFFSET,
.m_or =XTE_RXC1_RXVLAN_MASK,
},
/* Turn on FCS stripping on receive packets */
{
.opt = XTE_OPTION_FCS_STRIP,
.reg = XTE_RXC1_OFFSET,
.m_or =XTE_RXC1_RXFCS_MASK,
},
/* Turn on FCS insertion on transmit packets */
{
.opt = XTE_OPTION_FCS_INSERT,
.reg = XTE_TXC_OFFSET,
.m_or =XTE_TXC_TXFCS_MASK,
},
/* Turn on length/type field checking on receive packets */
{
.opt = XTE_OPTION_LENTYPE_ERR,
.reg = XTE_RXC1_OFFSET,
.m_or =XTE_RXC1_RXLT_MASK,
},
/* Turn on flow control */
{
.opt = XTE_OPTION_FLOW_CONTROL,
.reg = XTE_FCC_OFFSET,
.m_or =XTE_FCC_RXFLO_MASK,
},
/* Turn on flow control */
{
.opt = XTE_OPTION_FLOW_CONTROL,
.reg = XTE_FCC_OFFSET,
.m_or =XTE_FCC_TXFLO_MASK,
},
/* Turn on promiscuous frame filtering (all frames are received ) */
{
.opt = XTE_OPTION_PROMISC,
.reg = XTE_AFM_OFFSET,
.m_or =XTE_AFM_EPPRM_MASK,
},
/* Enable transmitter if not already enabled */
{
.opt = XTE_OPTION_TXEN,
.reg = XTE_TXC_OFFSET,
.m_or =XTE_TXC_TXEN_MASK,
},
/* Enable receiver? */
{
.opt = XTE_OPTION_RXEN,
.reg = XTE_RXC1_OFFSET,
.m_or =XTE_RXC1_RXEN_MASK,
},
{}
};
/**
* temac_setoptions
*/
static u32 temac_setoptions(struct net_device *ndev, u32 options)
{
struct temac_local *lp = netdev_priv(ndev);
struct temac_option *tp = &temac_options[0];
int reg;
mutex_lock(&lp->indirect_mutex);
while (tp->opt) {
reg = temac_indirect_in32(lp, tp->reg) & ~tp->m_or;
if (options & tp->opt)
reg |= tp->m_or;
temac_indirect_out32(lp, tp->reg, reg);
tp++;
}
lp->options |= options;
mutex_unlock(&lp->indirect_mutex);
return (0);
}
/* Initilize temac */
static void temac_device_reset(struct net_device *ndev)
{
struct temac_local *lp = netdev_priv(ndev);
u32 timeout;
u32 val;
/* Perform a software reset */
/* 0x300 host enable bit ? */
/* reset PHY through control register ?:1 */
dev_dbg(&ndev->dev, "%s()\n", __func__);
mutex_lock(&lp->indirect_mutex);
/* Reset the receiver and wait for it to finish reset */
temac_indirect_out32(lp, XTE_RXC1_OFFSET, XTE_RXC1_RXRST_MASK);
timeout = 1000;
while (temac_indirect_in32(lp, XTE_RXC1_OFFSET) & XTE_RXC1_RXRST_MASK) {
udelay(1);
if (--timeout == 0) {
dev_err(&ndev->dev,
"temac_device_reset RX reset timeout!!\n");
break;
}
}
/* Reset the transmitter and wait for it to finish reset */
temac_indirect_out32(lp, XTE_TXC_OFFSET, XTE_TXC_TXRST_MASK);
timeout = 1000;
while (temac_indirect_in32(lp, XTE_TXC_OFFSET) & XTE_TXC_TXRST_MASK) {
udelay(1);
if (--timeout == 0) {
dev_err(&ndev->dev,
"temac_device_reset TX reset timeout!!\n");
break;
}
}
/* Disable the receiver */
val = temac_indirect_in32(lp, XTE_RXC1_OFFSET);
temac_indirect_out32(lp, XTE_RXC1_OFFSET, val & ~XTE_RXC1_RXEN_MASK);
/* Reset Local Link (DMA) */
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
lp->dma_out(lp, DMA_CONTROL_REG, DMA_CONTROL_RST);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
timeout = 1000;
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
while (lp->dma_in(lp, DMA_CONTROL_REG) & DMA_CONTROL_RST) {
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
udelay(1);
if (--timeout == 0) {
dev_err(&ndev->dev,
"temac_device_reset DMA reset timeout!!\n");
break;
}
}
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
lp->dma_out(lp, DMA_CONTROL_REG, DMA_TAIL_ENABLE);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
ll_temac: add error checking to DMA init path Add error checking to DMA descriptor rings initialization code. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-01 01:39:05 +02:00
if (temac_dma_bd_init(ndev)) {
dev_err(&ndev->dev,
"temac_device_reset descriptor allocation failed\n");
}
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
temac_indirect_out32(lp, XTE_RXC0_OFFSET, 0);
temac_indirect_out32(lp, XTE_RXC1_OFFSET, 0);
temac_indirect_out32(lp, XTE_TXC_OFFSET, 0);
temac_indirect_out32(lp, XTE_FCC_OFFSET, XTE_FCC_RXFLO_MASK);
mutex_unlock(&lp->indirect_mutex);
/* Sync default options with HW
* but leave receiver and transmitter disabled. */
temac_setoptions(ndev,
lp->options & ~(XTE_OPTION_TXEN | XTE_OPTION_RXEN));
temac_set_mac_address(ndev, NULL);
/* Set address filter table */
temac_set_multicast_list(ndev);
if (temac_setoptions(ndev, lp->options))
dev_err(&ndev->dev, "Error setting TEMAC options\n");
/* Init Driver variable */
net: trans_start cleanups Now that core network takes care of trans_start updates, dont do it in drivers themselves, if possible. Drivers can avoid one cache miss (on dev->trans_start) in their start_xmit() handler. Exceptions are NETIF_F_LLTX drivers Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-10 14:01:31 +02:00
ndev->trans_start = jiffies; /* prevent tx timeout */
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
void temac_adjust_link(struct net_device *ndev)
{
struct temac_local *lp = netdev_priv(ndev);
struct phy_device *phy = lp->phy_dev;
u32 mii_speed;
int link_state;
/* hash together the state values to decide if something has changed */
link_state = phy->speed | (phy->duplex << 1) | phy->link;
mutex_lock(&lp->indirect_mutex);
if (lp->last_link != link_state) {
mii_speed = temac_indirect_in32(lp, XTE_EMCFG_OFFSET);
mii_speed &= ~XTE_EMCFG_LINKSPD_MASK;
switch (phy->speed) {
case SPEED_1000: mii_speed |= XTE_EMCFG_LINKSPD_1000; break;
case SPEED_100: mii_speed |= XTE_EMCFG_LINKSPD_100; break;
case SPEED_10: mii_speed |= XTE_EMCFG_LINKSPD_10; break;
}
/* Write new speed setting out to TEMAC */
temac_indirect_out32(lp, XTE_EMCFG_OFFSET, mii_speed);
lp->last_link = link_state;
phy_print_status(phy);
}
mutex_unlock(&lp->indirect_mutex);
}
static void temac_start_xmit_done(struct net_device *ndev)
{
struct temac_local *lp = netdev_priv(ndev);
struct cdmac_bd *cur_p;
unsigned int stat = 0;
cur_p = &lp->tx_bd_v[lp->tx_bd_ci];
stat = cur_p->app0;
while (stat & STS_CTRL_APP0_CMPLT) {
dma_unmap_single(ndev->dev.parent, cur_p->phys, cur_p->len,
DMA_TO_DEVICE);
if (cur_p->app4)
dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
cur_p->app0 = 0;
net: ll_temac: fix checksum offload logic The current checksum offload code does not work and this corrects that functionality. It also updates the interrupt coallescing initialization so than there are fewer interrupts and performance is increased. Signed-off-by: Brian Hill <brian.hill@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-27 05:44:30 +02:00
cur_p->app1 = 0;
cur_p->app2 = 0;
cur_p->app3 = 0;
cur_p->app4 = 0;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
ndev->stats.tx_packets++;
ndev->stats.tx_bytes += cur_p->len;
lp->tx_bd_ci++;
if (lp->tx_bd_ci >= TX_BD_NUM)
lp->tx_bd_ci = 0;
cur_p = &lp->tx_bd_v[lp->tx_bd_ci];
stat = cur_p->app0;
}
netif_wake_queue(ndev);
}
net: ll_temac: fix checksum offload logic The current checksum offload code does not work and this corrects that functionality. It also updates the interrupt coallescing initialization so than there are fewer interrupts and performance is increased. Signed-off-by: Brian Hill <brian.hill@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-27 05:44:30 +02:00
static inline int temac_check_tx_bd_space(struct temac_local *lp, int num_frag)
{
struct cdmac_bd *cur_p;
int tail;
tail = lp->tx_bd_tail;
cur_p = &lp->tx_bd_v[tail];
do {
if (cur_p->app0)
return NETDEV_TX_BUSY;
tail++;
if (tail >= TX_BD_NUM)
tail = 0;
cur_p = &lp->tx_bd_v[tail];
num_frag--;
} while (num_frag >= 0);
return 0;
}
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
static int temac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
{
struct temac_local *lp = netdev_priv(ndev);
struct cdmac_bd *cur_p;
dma_addr_t start_p, tail_p;
int ii;
unsigned long num_frag;
skb_frag_t *frag;
num_frag = skb_shinfo(skb)->nr_frags;
frag = &skb_shinfo(skb)->frags[0];
start_p = lp->tx_bd_p + sizeof(*lp->tx_bd_v) * lp->tx_bd_tail;
cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
net: ll_temac: fix checksum offload logic The current checksum offload code does not work and this corrects that functionality. It also updates the interrupt coallescing initialization so than there are fewer interrupts and performance is increased. Signed-off-by: Brian Hill <brian.hill@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-27 05:44:30 +02:00
if (temac_check_tx_bd_space(lp, num_frag)) {
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if (!netif_queue_stopped(ndev)) {
netif_stop_queue(ndev);
return NETDEV_TX_BUSY;
}
return NETDEV_TX_BUSY;
}
cur_p->app0 = 0;
if (skb->ip_summed == CHECKSUM_PARTIAL) {
net: ll_temac: fix checksum offload logic The current checksum offload code does not work and this corrects that functionality. It also updates the interrupt coallescing initialization so than there are fewer interrupts and performance is increased. Signed-off-by: Brian Hill <brian.hill@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-27 05:44:30 +02:00
unsigned int csum_start_off = skb_transport_offset(skb);
unsigned int csum_index_off = csum_start_off + skb->csum_offset;
cur_p->app0 |= 1; /* TX Checksum Enabled */
cur_p->app1 = (csum_start_off << 16) | csum_index_off;
cur_p->app2 = 0; /* initial checksum seed */
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
net: ll_temac: fix checksum offload logic The current checksum offload code does not work and this corrects that functionality. It also updates the interrupt coallescing initialization so than there are fewer interrupts and performance is increased. Signed-off-by: Brian Hill <brian.hill@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-27 05:44:30 +02:00
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
cur_p->app0 |= STS_CTRL_APP0_SOP;
cur_p->len = skb_headlen(skb);
cur_p->phys = dma_map_single(ndev->dev.parent, skb->data, skb->len,
DMA_TO_DEVICE);
cur_p->app4 = (unsigned long)skb;
for (ii = 0; ii < num_frag; ii++) {
lp->tx_bd_tail++;
if (lp->tx_bd_tail >= TX_BD_NUM)
lp->tx_bd_tail = 0;
cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
cur_p->phys = dma_map_single(ndev->dev.parent,
(void *)page_address(frag->page) +
frag->page_offset,
frag->size, DMA_TO_DEVICE);
cur_p->len = frag->size;
cur_p->app0 = 0;
frag++;
}
cur_p->app0 |= STS_CTRL_APP0_EOP;
tail_p = lp->tx_bd_p + sizeof(*lp->tx_bd_v) * lp->tx_bd_tail;
lp->tx_bd_tail++;
if (lp->tx_bd_tail >= TX_BD_NUM)
lp->tx_bd_tail = 0;
/* Kick off the transfer */
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
lp->dma_out(lp, TX_TAILDESC_PTR, tail_p); /* DMA start */
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
net: use NETDEV_TX_OK instead of 0 in ndo_start_xmit() functions This patch is the result of an automatic spatch transformation to convert all ndo_start_xmit() return values of 0 to NETDEV_TX_OK. Some occurences are missed by the automatic conversion, those will be handled in a seperate patch. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-23 08:03:08 +02:00
return NETDEV_TX_OK;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
static void ll_temac_recv(struct net_device *ndev)
{
struct temac_local *lp = netdev_priv(ndev);
struct sk_buff *skb, *new_skb;
unsigned int bdstat;
struct cdmac_bd *cur_p;
dma_addr_t tail_p;
int length;
unsigned long flags;
spin_lock_irqsave(&lp->rx_lock, flags);
tail_p = lp->rx_bd_p + sizeof(*lp->rx_bd_v) * lp->rx_bd_ci;
cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
bdstat = cur_p->app0;
while ((bdstat & STS_CTRL_APP0_CMPLT)) {
skb = lp->rx_skb[lp->rx_bd_ci];
ll_temac: Add support for V2 LLTEMAC core LLTEMAC V1 cores place only received packet length in the app4 word. V2 cores place additional information in app4. Mask out the additional information when retrieving the packet length. Signed-off-by: Steven J. Magnani <steve@digidescorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-17 08:14:20 +01:00
length = cur_p->app4 & 0x3FFF;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
net: ll_temac: remove virt_to_bus call The virt_to_bus call should not be used any longer as it's considered illegal. The driver has the physical address of the buffer in the descriptor such that it's not necessary anyway. Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:01 +02:00
dma_unmap_single(ndev->dev.parent, cur_p->phys, length,
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
DMA_FROM_DEVICE);
skb_put(skb, length);
skb->dev = ndev;
skb->protocol = eth_type_trans(skb, ndev);
skb->ip_summed = CHECKSUM_NONE;
net: ll_temac: fix checksum offload logic The current checksum offload code does not work and this corrects that functionality. It also updates the interrupt coallescing initialization so than there are fewer interrupts and performance is increased. Signed-off-by: Brian Hill <brian.hill@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-27 05:44:30 +02:00
/* if we're doing rx csum offload, set it up */
if (((lp->temac_features & TEMAC_FEATURE_RX_CSUM) != 0) &&
(skb->protocol == __constant_htons(ETH_P_IP)) &&
(skb->len > 64)) {
skb->csum = cur_p->app3 & 0xFFFF;
skb->ip_summed = CHECKSUM_COMPLETE;
}
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
netif_rx(skb);
ndev->stats.rx_packets++;
ndev->stats.rx_bytes += length;
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
new_skb = netdev_alloc_skb_ip_align(ndev,
XTE_MAX_JUMBO_FRAME_SIZE);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if (new_skb == 0) {
dev_err(&ndev->dev, "no memory for new sk_buff\n");
spin_unlock_irqrestore(&lp->rx_lock, flags);
return;
}
cur_p->app0 = STS_CTRL_APP0_IRQONEND;
cur_p->phys = dma_map_single(ndev->dev.parent, new_skb->data,
XTE_MAX_JUMBO_FRAME_SIZE,
DMA_FROM_DEVICE);
cur_p->len = XTE_MAX_JUMBO_FRAME_SIZE;
lp->rx_skb[lp->rx_bd_ci] = new_skb;
lp->rx_bd_ci++;
if (lp->rx_bd_ci >= RX_BD_NUM)
lp->rx_bd_ci = 0;
cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
bdstat = cur_p->app0;
}
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
lp->dma_out(lp, RX_TAILDESC_PTR, tail_p);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
spin_unlock_irqrestore(&lp->rx_lock, flags);
}
static irqreturn_t ll_temac_tx_irq(int irq, void *_ndev)
{
struct net_device *ndev = _ndev;
struct temac_local *lp = netdev_priv(ndev);
unsigned int status;
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
status = lp->dma_in(lp, TX_IRQ_REG);
lp->dma_out(lp, TX_IRQ_REG, status);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if (status & (IRQ_COAL | IRQ_DLY))
temac_start_xmit_done(lp->ndev);
if (status & 0x080)
dev_err(&ndev->dev, "DMA error 0x%x\n", status);
return IRQ_HANDLED;
}
static irqreturn_t ll_temac_rx_irq(int irq, void *_ndev)
{
struct net_device *ndev = _ndev;
struct temac_local *lp = netdev_priv(ndev);
unsigned int status;
/* Read and clear the status registers */
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
status = lp->dma_in(lp, RX_IRQ_REG);
lp->dma_out(lp, RX_IRQ_REG, status);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if (status & (IRQ_COAL | IRQ_DLY))
ll_temac_recv(lp->ndev);
return IRQ_HANDLED;
}
static int temac_open(struct net_device *ndev)
{
struct temac_local *lp = netdev_priv(ndev);
int rc;
dev_dbg(&ndev->dev, "temac_open()\n");
if (lp->phy_node) {
lp->phy_dev = of_phy_connect(lp->ndev, lp->phy_node,
temac_adjust_link, 0, 0);
if (!lp->phy_dev) {
dev_err(lp->dev, "of_phy_connect() failed\n");
return -ENODEV;
}
phy_start(lp->phy_dev);
}
rc = request_irq(lp->tx_irq, ll_temac_tx_irq, 0, ndev->name, ndev);
if (rc)
goto err_tx_irq;
rc = request_irq(lp->rx_irq, ll_temac_rx_irq, 0, ndev->name, ndev);
if (rc)
goto err_rx_irq;
temac_device_reset(ndev);
return 0;
err_rx_irq:
free_irq(lp->tx_irq, ndev);
err_tx_irq:
if (lp->phy_dev)
phy_disconnect(lp->phy_dev);
lp->phy_dev = NULL;
dev_err(lp->dev, "request_irq() failed\n");
return rc;
}
static int temac_stop(struct net_device *ndev)
{
struct temac_local *lp = netdev_priv(ndev);
dev_dbg(&ndev->dev, "temac_close()\n");
free_irq(lp->tx_irq, ndev);
free_irq(lp->rx_irq, ndev);
if (lp->phy_dev)
phy_disconnect(lp->phy_dev);
lp->phy_dev = NULL;
return 0;
}
#ifdef CONFIG_NET_POLL_CONTROLLER
static void
temac_poll_controller(struct net_device *ndev)
{
struct temac_local *lp = netdev_priv(ndev);
disable_irq(lp->tx_irq);
disable_irq(lp->rx_irq);
ll_temac_rx_irq(lp->tx_irq, lp);
ll_temac_tx_irq(lp->rx_irq, lp);
enable_irq(lp->tx_irq);
enable_irq(lp->rx_irq);
}
#endif
static const struct net_device_ops temac_netdev_ops = {
.ndo_open = temac_open,
.ndo_stop = temac_stop,
.ndo_start_xmit = temac_start_xmit,
ll_temac: Fix MAC address configuration from userland A userland command to set the LLTEMAC MAC address, i.e. "ifconfig eth0 hw addr xx:yy:zz:pp:dd:qq", results in a device address of 00:01:xx:yy:zz:pp. Correct this. Signed-off-by: Steven J. Magnani <steve@digidescorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-17 08:55:07 +01:00
.ndo_set_mac_address = netdev_set_mac_address,
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
//.ndo_set_multicast_list = temac_set_multicast_list,
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = temac_poll_controller,
#endif
};
/* ---------------------------------------------------------------------
* SYSFS device attributes
*/
static ssize_t temac_show_llink_regs(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct net_device *ndev = dev_get_drvdata(dev);
struct temac_local *lp = netdev_priv(ndev);
int i, len = 0;
for (i = 0; i < 0x11; i++)
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
len += sprintf(buf + len, "%.8x%s", lp->dma_in(lp, i),
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
(i % 8) == 7 ? "\n" : " ");
len += sprintf(buf + len, "\n");
return len;
}
static DEVICE_ATTR(llink_regs, 0440, temac_show_llink_regs, NULL);
static struct attribute *temac_device_attrs[] = {
&dev_attr_llink_regs.attr,
NULL,
};
static const struct attribute_group temac_attr_group = {
.attrs = temac_device_attrs,
};
static int __init
temac_of_probe(struct of_device *op, const struct of_device_id *match)
{
struct device_node *np;
struct temac_local *lp;
struct net_device *ndev;
const void *addr;
net: ll_temac: fix checksum offload logic The current checksum offload code does not work and this corrects that functionality. It also updates the interrupt coallescing initialization so than there are fewer interrupts and performance is increased. Signed-off-by: Brian Hill <brian.hill@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-27 05:44:30 +02:00
__be32 *p;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
int size, rc = 0;
/* Init network device structure */
ndev = alloc_etherdev(sizeof(*lp));
if (!ndev) {
dev_err(&op->dev, "could not allocate device.\n");
return -ENOMEM;
}
ether_setup(ndev);
dev_set_drvdata(&op->dev, ndev);
SET_NETDEV_DEV(ndev, &op->dev);
ndev->flags &= ~IFF_MULTICAST; /* clear multicast */
ndev->features = NETIF_F_SG | NETIF_F_FRAGLIST;
ndev->netdev_ops = &temac_netdev_ops;
#if 0
ndev->features |= NETIF_F_IP_CSUM; /* Can checksum TCP/UDP over IPv4. */
ndev->features |= NETIF_F_HW_CSUM; /* Can checksum all the packets. */
ndev->features |= NETIF_F_IPV6_CSUM; /* Can checksum IPV6 TCP/UDP */
ndev->features |= NETIF_F_HIGHDMA; /* Can DMA to high memory. */
ndev->features |= NETIF_F_HW_VLAN_TX; /* Transmit VLAN hw accel */
ndev->features |= NETIF_F_HW_VLAN_RX; /* Receive VLAN hw acceleration */
ndev->features |= NETIF_F_HW_VLAN_FILTER; /* Receive VLAN filtering */
ndev->features |= NETIF_F_VLAN_CHALLENGED; /* cannot handle VLAN pkts */
ndev->features |= NETIF_F_GSO; /* Enable software GSO. */
ndev->features |= NETIF_F_MULTI_QUEUE; /* Has multiple TX/RX queues */
ndev->features |= NETIF_F_LRO; /* large receive offload */
#endif
/* setup temac private info structure */
lp = netdev_priv(ndev);
lp->ndev = ndev;
lp->dev = &op->dev;
lp->options = XTE_OPTION_DEFAULTS;
spin_lock_init(&lp->rx_lock);
mutex_init(&lp->indirect_mutex);
/* map device registers */
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
lp->regs = of_iomap(op->dev.of_node, 0);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if (!lp->regs) {
dev_err(&op->dev, "could not map temac regs.\n");
goto nodev;
}
net: ll_temac: fix checksum offload logic The current checksum offload code does not work and this corrects that functionality. It also updates the interrupt coallescing initialization so than there are fewer interrupts and performance is increased. Signed-off-by: Brian Hill <brian.hill@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-27 05:44:30 +02:00
/* Setup checksum offload, but default to off if not specified */
lp->temac_features = 0;
p = (__be32 *)of_get_property(op->dev.of_node, "xlnx,txcsum", NULL);
if (p && be32_to_cpu(*p)) {
lp->temac_features |= TEMAC_FEATURE_TX_CSUM;
/* Can checksum TCP/UDP over IPv4. */
ndev->features |= NETIF_F_IP_CSUM;
}
p = (__be32 *)of_get_property(op->dev.of_node, "xlnx,rxcsum", NULL);
if (p && be32_to_cpu(*p))
lp->temac_features |= TEMAC_FEATURE_RX_CSUM;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
/* Find the DMA node, map the DMA registers, and decode the DMA IRQs */
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
np = of_parse_phandle(op->dev.of_node, "llink-connected", 0);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if (!np) {
dev_err(&op->dev, "could not find DMA node\n");
ll_temac: Fix missing iounmaps Fix missing iounmaps. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-05 23:44:20 +02:00
goto err_iounmap;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
/* Setup the DMA register accesses, could be DCR or memory mapped */
if (temac_dcr_setup(lp, op, np)) {
/* no DCR in the device tree, try non-DCR */
lp->sdma_regs = of_iomap(np, 0);
if (lp->sdma_regs) {
lp->dma_in = temac_dma_in32;
lp->dma_out = temac_dma_out32;
dev_dbg(&op->dev, "MEM base: %p\n", lp->sdma_regs);
} else {
dev_err(&op->dev, "unable to map DMA registers\n");
ll_temac: Fix missing iounmaps Fix missing iounmaps. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-05 23:44:20 +02:00
goto err_iounmap;
Add non-Virtex5 support for LL TEMAC driver This patch adds support for using the LL TEMAC Ethernet driver on non-Virtex 5 platforms by adding support for accessing the Soft DMA registers as if they were memory mapped instead of solely through the DCR's (available on the Virtex 5). The patch also updates the driver so that it runs on the MicroBlaze. The changes were tested on the PowerPC 440, PowerPC 405, and the MicroBlaze platforms. Signed-off-by: John Tyner <jtyner@cs.ucr.edu> Signed-off-by: John Linn <john.linn@xilinx.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-08 09:08:02 +02:00
}
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
lp->rx_irq = irq_of_parse_and_map(np, 0);
lp->tx_irq = irq_of_parse_and_map(np, 1);
net: ll_temac: fix interrupt bug when interrupt 0 is used The code is not checking the interrupt for DMA correctly so that an interrupt number of 0 will cause a false error. Signed-off-by: Brian Hill <brian.hill@xilinx.com> Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-27 05:42:18 +02:00
if ((lp->rx_irq == NO_IRQ) || (lp->tx_irq == NO_IRQ)) {
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
dev_err(&op->dev, "could not determine irqs\n");
rc = -ENOMEM;
ll_temac: Fix missing iounmaps Fix missing iounmaps. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-05 23:44:20 +02:00
goto err_iounmap_2;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
of_node_put(np); /* Finished with the DMA node; drop the reference */
/* Retrieve the MAC address */
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
addr = of_get_property(op->dev.of_node, "local-mac-address", &size);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if ((!addr) || (size != 6)) {
dev_err(&op->dev, "could not find MAC address\n");
rc = -ENODEV;
ll_temac: Fix missing iounmaps Fix missing iounmaps. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-05 23:44:20 +02:00
goto err_iounmap_2;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
temac_set_mac_address(ndev, (void *)addr);
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
rc = temac_mdio_setup(lp, op->dev.of_node);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if (rc)
dev_warn(&op->dev, "error registering MDIO bus\n");
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
lp->phy_node = of_parse_phandle(op->dev.of_node, "phy-handle", 0);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
if (lp->phy_node)
dev_dbg(lp->dev, "using PHY node %s (%p)\n", np->full_name, np);
/* Add the device attributes */
rc = sysfs_create_group(&lp->dev->kobj, &temac_attr_group);
if (rc) {
dev_err(lp->dev, "Error creating sysfs files\n");
ll_temac: Fix missing iounmaps Fix missing iounmaps. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-05 23:44:20 +02:00
goto err_iounmap_2;
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
}
rc = register_netdev(lp->ndev);
if (rc) {
dev_err(lp->dev, "register_netdev() error (%i)\n", rc);
goto err_register_ndev;
}
return 0;
err_register_ndev:
sysfs_remove_group(&lp->dev->kobj, &temac_attr_group);
ll_temac: Fix missing iounmaps Fix missing iounmaps. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-05 23:44:20 +02:00
err_iounmap_2:
if (lp->sdma_regs)
iounmap(lp->sdma_regs);
err_iounmap:
iounmap(lp->regs);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
nodev:
free_netdev(ndev);
ndev = NULL;
return rc;
}
static int __devexit temac_of_remove(struct of_device *op)
{
struct net_device *ndev = dev_get_drvdata(&op->dev);
struct temac_local *lp = netdev_priv(ndev);
temac_mdio_teardown(lp);
unregister_netdev(ndev);
sysfs_remove_group(&lp->dev->kobj, &temac_attr_group);
if (lp->phy_node)
of_node_put(lp->phy_node);
lp->phy_node = NULL;
dev_set_drvdata(&op->dev, NULL);
ll_temac: Fix missing iounmaps Fix missing iounmaps. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-05 23:44:20 +02:00
iounmap(lp->regs);
if (lp->sdma_regs)
iounmap(lp->sdma_regs);
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
free_netdev(ndev);
return 0;
}
static struct of_device_id temac_of_match[] __devinitdata = {
{ .compatible = "xlnx,xps-ll-temac-1.01.b", },
ll_temac: Add support for V2 LLTEMAC core LLTEMAC V1 cores place only received packet length in the app4 word. V2 cores place additional information in app4. Mask out the additional information when retrieving the packet length. Signed-off-by: Steven J. Magnani <steve@digidescorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-17 08:14:20 +01:00
{ .compatible = "xlnx,xps-ll-temac-2.00.a", },
{ .compatible = "xlnx,xps-ll-temac-2.02.a", },
{ .compatible = "xlnx,xps-ll-temac-2.03.a", },
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
{},
};
MODULE_DEVICE_TABLE(of, temac_of_match);
static struct of_platform_driver temac_of_driver = {
.probe = temac_of_probe,
.remove = __devexit_p(temac_of_remove),
.driver = {
.owner = THIS_MODULE,
.name = "xilinx_temac",
of: Remove duplicate fields from of_platform_driver .name, .match_table and .owner are duplicated in both of_platform_driver and device_driver. This patch is a removes the extra copies from struct of_platform_driver and converts all users to the device_driver members. This patch is a pretty mechanical change. The usage model doesn't change and if any drivers have been missed, or if anything has been fixed up incorrectly, then it will fail with a compile time error, and the fixup will be trivial. This patch looks big and scary because it touches so many files, but it should be pretty safe. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Sean MacLennan <smaclennan@pikatech.com>
2010-04-14 01:13:02 +02:00
.of_match_table = temac_of_match,
net: add Xilinx ll_temac device driver This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-25 14:53:39 +02:00
},
};
static int __init temac_init(void)
{
return of_register_platform_driver(&temac_of_driver);
}
module_init(temac_init);
static void __exit temac_exit(void)
{
of_unregister_platform_driver(&temac_of_driver);
}
module_exit(temac_exit);
MODULE_DESCRIPTION("Xilinx LL_TEMAC Ethernet driver");
MODULE_AUTHOR("Yoshio Kashiwagi");
MODULE_LICENSE("GPL");
Reference in a new issue Copy permalink