gpio: Move GE GPIO driver to reside within GPIO subsystem

The GE GPIO driver provides basic support (set direction, read/write state)
for the GPIO provided on some GE single board computers. This patch moves
the driver from the 86xx specific platform directrory to the GPIO subsystem
so that it can be used on non-86xx boards.

Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This commit is contained in:
Martyn Welch 2012-03-12 17:12:58 +00:00 committed by Kumar Gala
parent 330bbf4854
commit 6518bb69f4
7 changed files with 18 additions and 3 deletions

View file

@ -131,6 +131,7 @@ CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MPC=y
CONFIG_GPIO_SYSFS=y
CONFIG_GPIO_GE_FPGA=y
CONFIG_SENSORS_LM90=y
CONFIG_SENSORS_LM92=y
CONFIG_WATCHDOG=y

View file

@ -132,6 +132,7 @@ CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MPC=y
CONFIG_GPIO_SYSFS=y
CONFIG_GPIO_GE_FPGA=y
CONFIG_SENSORS_LM90=y
CONFIG_SENSORS_LM92=y
CONFIG_WATCHDOG=y

View file

@ -183,6 +183,8 @@ CONFIG_NVRAM=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MPC=y
CONFIG_GPIO_SYSFS=y
CONFIG_GPIO_GE_FPGA=y
CONFIG_SENSORS_LM90=y
CONFIG_SENSORS_LM92=y
CONFIG_WATCHDOG=y

View file

@ -7,8 +7,7 @@ obj-$(CONFIG_SMP) += mpc86xx_smp.o
obj-$(CONFIG_MPC8641_HPCN) += mpc86xx_hpcn.o
obj-$(CONFIG_SBC8641D) += sbc8641d.o
obj-$(CONFIG_MPC8610_HPCD) += mpc8610_hpcd.o
gef-gpio-$(CONFIG_GPIOLIB) += gef_gpio.o
obj-$(CONFIG_GE_FPGA) += gef_pic.o $(gef-gpio-y)
obj-$(CONFIG_GE_FPGA) += gef_pic.o
obj-$(CONFIG_GEF_SBC610) += gef_sbc610.o
obj-$(CONFIG_GEF_SBC310) += gef_sbc310.o
obj-$(CONFIG_GEF_PPC9A) += gef_ppc9a.o

View file

@ -190,6 +190,17 @@ config GPIO_VX855
additional drivers must be enabled in order to use the
functionality of the device.
config GPIO_GE_FPGA
bool "GE FPGA based GPIO"
depends on GE_FPGA
help
Support for common GPIO functionality provided on some GE Single Board
Computers.
This driver provides basic support (configure as input or output, read
and write pin state) for GPIO implemented in a number of GE single
board computers.
comment "I2C GPIO expanders:"
config GPIO_MAX7300

View file

@ -16,6 +16,7 @@ obj-$(CONFIG_GPIO_CS5535) += gpio-cs5535.o
obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o
obj-$(CONFIG_ARCH_DAVINCI) += gpio-davinci.o
obj-$(CONFIG_GPIO_EP93XX) += gpio-ep93xx.o
obj-$(CONFIG_GPIO_GE_FPGA) += gpio-ge.o
obj-$(CONFIG_GPIO_IT8761E) += gpio-it8761e.o
obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o
obj-$(CONFIG_ARCH_KS8695) += gpio-ks8695.o

View file

@ -14,7 +14,7 @@
*
* Configuration of output modes (totem-pole/open-drain)
* Interrupt configuration - interrupts are always generated the FPGA relies on
* the I/O interrupt controllers mask to stop them propergating
* the I/O interrupt controllers mask to stop them propergating
*/
#include <linux/kernel.h>