It has been determined that the workaround of putting the PHY into MDIO
slow mode to access the PHY id is not necessary with Lynx Point and newer
parts. The issue that necessitated the workaround has been fixed on the
newer hardware.
We will maintains, as a last ditch attempt, the conversion to MDIO Slow
Mode in the failure branch when attempting to access the PHY id so as to
cover all contingencies.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
link partners. Issue has been root caused as interoperability problem
between 82579 and at least some Broadcom PHYs in the Energy Efficient
Ethernet wake mechanism.
To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle. This solution will cause an increase of power in 100M EEE
link. It will cost additional 28mW in this specific mode.
Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 772d05c51c "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.
This same behavior is seen on i217 and i218 parts as well. This patch expands
the original workaround to encompass these parts.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a workaround for a HW erratum on 82579 devices.
Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset
specification Update June 2013.
Problem: 82579 parts experience packet loss in Gig and 100 speeds
when interconnect between PHY and MAC is exiting K1 power saving state.
This was previously believed to only affect 1Gig speed, but has been observed
at 100Mbs also.
Workaround: Disable K1 for 82579 devices at Gig and 100 speeds.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Or Gerlitz says:
====================
This series contains fixes for 3.15-rc, mostly around SRIOV. The patches by Jack,
Matan and myself fix few issues related to mlx4 SRIOV support for RoCE and single
port VFs, and the patch from Eyal eliminates checking PCI caps for VFs which is misleading.
Patches done against the net tree, commit 014f1b2 "net: bonding: Fix format string
mismatch in bond_sysfs.c"
We'd be happy to get Eyal's patch queued in your -stable list for 3.14.y
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Carrying out PCI speed/width checks through pcie_get_minimum_link()
on VFs yield wrong results, so remove them.
Fixes: b912b2f ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth')
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in SRIOV mode, VM that is assigned with a non-provisioned
Ethernet VFs get themselves a random mac when the Eth driver starts. In
this case, if the IB driver startup code that deals with RoCE runs first,
it will use a zero mac as the source mac for the Para-Virtual CM MADs
which is buggy. To handle that, we change the order of loading.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that deals with computing the slave id based on a given GID
gave wrong results when the number of single port VFs wasn't the
same for port 1 vs. port 2 and the relevant VF is single ported on
port 2. As a result, incoming CM MADs were dispatched to the wrong VF.
Fixed that and added documentation to clarify the computation steps.
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using single ported VFs and the VF is using port 2, we need
to adjust the port accordingly (change it from 1 to 2).
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces another flag in 'quirks' to replace the preprocessor
define (USE_MMIO) used to indicate whether the device needs a
separate enable routine to operate in MMIO mode.
All of the currently known platform Rhine cores operate in MMIO
mode by default, and on PCI it is preferred over PIO for performance
reasons. However, a comment in code suggests that some (?) early
Rhine cores only work in PIO mode, so they should not be switched
to MMIO.
Enabling MMIO on PCI is still triggered by the same Kconfig option
to avoid breaking user configs needlessly, but this can be changed
going forward towards automatic runtime detection in case a list of
PIO-only Rhine revisions can be compiled.
This also fixes a couple of compiler warnings detected by Fengguang
Wu's test bot (!USE_MMIO case):
drivers/net/ethernet/via/via-rhine.c: In function 'rhine_init_one_pci':
drivers/net/ethernet/via/via-rhine.c:1108:1: warning: label 'err_out_unmap' defined but not used [-Wunused-label]
err_out_unmap:
^
drivers/net/ethernet/via/via-rhine.c:1022:6: warning: unused variable 'i' [-Wunused-variable]
int i, rc;
^
drivers/net/ethernet/via/via-rhine.c:916:22: warning: 'quirks' may be used uninitialized in this function [-Wmaybe-uninitialized]
phy_id = rp->quirks & rqIntPHY ? 1 : 0;
^
drivers/net/ethernet/via/via-rhine.c:1026:6: note: 'quirks' was declared here
u32 quirks;
^
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is no longer used after commit e837735ec4
(ip6_tunnel: ensure to always have a link local address).
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
net: Checksum offload changes
I am working on overhauling RX checksum offload. Goals of this effort
are:
- Specify what exactly it means when driver returns CHECKSUM_UNNECESSARY
- Preserve CHECKSUM_COMPLETE through encapsulation layers
- Don't do skb_checksum more than once per packet
- Unify GRO and non-GRO csum verification as much as possible
- Unify the checksum functions (checksum_init)
- Simply code
What is in this first patch set:
- Create a common "checksum_init" function which is called from
TCPv{4,6} and UDPv{4,6}
- Add some for RFC6936, UDP/IPv6 zero checksums
- Add architecture support for csum_add and provide implementations
for x86_64 and Sparc 32 and 64 bit (please test the latter)
Please review carefully and test if possible, mucking with basic
checksum functions is always a little precarious :-)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 6936 relaxes the requirement of RFC 2460 that UDP/IPv6 packets which
are received with a zero UDP checksum value must be dropped. RFC 6936
allows zero checksums to support tunnels over UDP.
When sk_no_check is set we allow on a socket we allow a zero IPv6
UDP checksum. This is for both sending zero checksum and accepting
a zero checksum on receive.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_checksum_init instead of private functions.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_checksum_init instead of private functions.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a general __skb_checksum_validate function (actually a
macro) to subsume the various checksum_init functions. This
function can either init the checksum, or do the full validation
(logically checksum_init+skb_check_complete)-- a flag specifies
if full vaidation is performed. Also, there is a flag to the function
to indicate that zero checksums are allowed (to support optional
UDP checksums).
Added several stub functions for calling __skb_checksum_validate.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note add32_with_carry(a, b) is suboptimal, as it forces
a and b in registers.
b could be a memory or a register operand.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
csum_add is really nothing more then add-with-carry which
can be implemented efficiently in some architectures.
Allow architecture to define this protected by HAVE_ARCH_CSUM_ADD.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4d619f625a ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set. This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.
Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.
Fixes: 4d619f625a ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-05-02
Please pull this batch of updates intended for the 3.16 stream...
For the mac80211 bits, Johannes says:
"In this round we have a large number of small features and
improvements from people too numerous to list here. The only really
bit thing is Michał and Luca's CSA work (including changing how
interface combination verification is done)."
For the Bluetooth bits, Gustavo says:
"Here goes some patches for the -next release. There is nothing
really special for this pull request, just a bunch of refactors,
fixes and clean ups."
For the ath10k/ath6kl bits, Kalle says:
"For ath6kl Kalle fixed a bunch of checkpatch warnings.
In ath10k we had more changes, major ones being:
* fix memory allocation failures after a firmware crash (Michal)
* some rework of DFS configuration to enable it correctly in all cases
(Michal)
* add a new firmware crash option to make it possible to crash 10.1
firmware for testing purposes (Marek P)
* fix RTS/CTS protection in certain cases (Marek K)
* fix wrong RSSI and rate reporting in some cases (Janusz)
* fix firmware stats reporting (Chun, Ben & Bartosz)"
For the iwlwifi bits, Emmanuel says:
"I have here a bunch of unrelated things. I disabled support for
-7.ucode which means that I can removed a lot of code. Eliad has
a brand new feature: we reduce the Tx power when the link allows -
this reduces our power consumption. The regular changes in power and
scan area. One interesting thing though is the patches from Johannes,
we have now GRO which allows to increase our throughput in TCP Rx. The
main advantage is that it reduces the number of TCP Acks - these TCP
Acks are completely useless when we are using A-MPDU since the first
packet of the A-MPDU generates a TCP Ack which is made obsolete by
the next packets."
Along with that, there are a variety of updates to b43, mwifiex,
rtl8180 and wil6210 drivers and a handful of other updates here
and there.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
George Cherian says:
====================
The series adds CPTS support for AM4372.
Patch 1 - DT changes w.r.t clock changes for AM33xx.
Patch 2 - CPTS clock name harcoding in the driver is removed.
Easier to pass the clock name from dt rather than hardcoding in driver.
Also in prepration for DRA7x CPTS support.
Patch 3 - Enable the CPTS support for both DRA7x and AM4372 in the driver.
Patch 4 - Enable the Annexe F for L2 PTP for AM437x and DRA7x.
Patch 5 - Change the default clocksource to dpll_core_m5
Patch 6 - DT changes for AM4372.
v1 -> v2
Patch 1 and 2 Re-ordering.
Seperate TS_BITS define for Hw version V2 and V3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CPSW fck and CPTS clock and clock names for AM4372
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpsw_cpts_rft_clk has got the choice of 3 clocksources
-dpll_core_m4_ck
-dpll_core_m5_ck
-dpll_disp_m2_ck
By default dpll_core_m4_ck is selected, witn this as clock
source the CPTS doesnot work properly. It gives clockcheck errors
while running PTP.
clockcheck: clock jumped backward or running slower than expected!
By selecting dpll_core_m5_ck as the clocksource fixes this issue.
In AM335x dpll_core_m5_ck is the default clocksource.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the Annex F Time Sync explicitly for DRA7x and AM4372.
With this enabled the L2 PTP is working.
while at that rename TS_BIT8 to TS_TTL_NONZERO
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable cpts hardware time stamping for Dra7xx and AM4372.
This enables PTPv2 for DRA7xx and AM4372.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPTS refclk name is hardcoded, which makes it fail in case of DRA7x
Remove the hardcoded clock name for CPTS refclk and get the same from DT.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `altera_tse_probe':
altera_tse_main.c:(.text+0x25ec2e): undefined reference to `dma_set_mask'
altera_tse_main.c:(.text+0x25ec78): undefined reference to `dma_supported'
altera_tse_main.c:(.text+0x25ecb6): undefined reference to `dma_supported'
drivers/built-in.o: In function `sgdma_async_read':
altera_sgdma.c:(.text+0x25f620): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f678): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f696): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f6f0): undefined reference to `dma_map_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f702): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `sgdma_tx_buffer':
(.text+0x25f92a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_rx_status':
(.text+0x25fa24): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the core vsock module is the owner of the proto family. This
means there's nothing preventing the transport module from unloading if
there are open sockets, which results in a panic. Fix that by allowing
the transport to be the owner, which will refcount it properly.
Includes version bump to 1.0.1.0-k
Passes checkpatch this time, I swear...
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes ordering of rtnl notifications during unregister_netdevice
by moving RTM_DELLINK notification to until after ndo_uninit.
The problem was seen with unregistering bond netdevices.
bond ndo_uninit callback generates a few RTM_NEWLINK notifications for
NETDEV_CHANGEADDR and NETDEV_FEAT_CHANGE. This is seen mostly when the
bond is deleted with slaves still enslaved to the bond.
During unregister netdevice (rollback_registered_many to be specific)
bond ndo_uninit is called after RTM_DELLINK notification goes out.
This results in userspace seeing RTM_DELLINK followed by a couple of
RTM_NEWLINK's.
In userspace problem was seen with libnl. libnl cache deletes the bond
when it sees RTM_DELLINK and re-adds the bond with the following
RTM_NEWLINK. Resulting in a stale bond entry in libnl cache when the kernel
has already deleted the bond.
This patch has been tested for bond, bridges and vlan devices.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-05-01
Please pull the following batch of fixes intended for the 3.15 stream!
For the Bluetooth bits, Gustavo says:
"Some fixes for 3.15. There is a revert for the intel driver, a new
device id, and two important SSP fixes from Johan."
On top of that...
Ben Hutchings gives us a fix for an unbalanced irq enable in an
rtl8192cu error path.
Colin Ian King provides an rtlwifi fix for an uninitialized variable.
Felix Fietkau brings a pair of ath9k fixes, one that corrects a
hardware initialization value and another that removes an (unnecessary)
flag that was being used in a way that led to a software tx queue
hang in ath9k.
Gertjan van Wingerde pushes a MAINTAINERS change to remove himself
from the rt2x00 maintainer team.
Hans de Goede fixes a brcmfmac firmware load hang.
Larry Finger changes rtlwifi to use the correct queue for V0 traffic
on rtl8192se.
Rajkumar Manoharan corrects a race in ath9k driver initialization.
Stanislaw Gruszka fixes an rt2x00 bug in which disabling beaconing
once on USB devices led to permanently disabling beaconing for those
devices.
Tim Harvey provides fixes for a pair of ath9k issues that can lead
to soft lockups in that driver.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Build console support only when CONFIG_TTY is selected.
This restores ISS as the default platform for allnoconfig builds.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Unpaired quotes really confuse mutt when copy & pasting it into the To:
form.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[ I'm going to remove all silly quotes entirely one day, but that day is
not today. So I'll just apply this - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 2 real bug-fixes from Tanya for the still "experimental" UBI fastmap feature
* a one-liner from Kees which hardens kernel security
* a small error-path fix, where we forget to free various resources in case of
failure - spotted by the "smatch" tool
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=L0f1
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.15-rc5' of git://git.infradead.org/linux-ubifs
Pull ubifs fixes from Artem Bityutskiy:
"This includes the following fixes:
- two real bug-fixes from Tanya for the still "experimental" UBI
fastmap feature
- a one-liner from Kees which hardens kernel security
- a small error-path fix, where we forget to free various resources
in case of failure - spotted by the 'smatch' tool"
* tag 'upstream-3.15-rc5' of git://git.infradead.org/linux-ubifs:
UBI: avoid workqueue format string leak
UBI: fix ubi free PEBs count calculation
UBI: fix error path in __wl_get_peb
UBIFS: fix remount error path
Do not leak kernel-only floppy_raw_cmd structure members to userspace.
This includes the linked-list pointer and the pointer to the allocated
DMA space.
Signed-off-by: Matthew Daley <mattd@bugfuzz.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Always clear out these floppy_raw_cmd struct members after copying the
entire structure from userspace so that the in-kernel version is always
valid and never left in an interdeterminate state.
Signed-off-by: Matthew Daley <mattd@bugfuzz.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently bridge can silently drop ipv4 fragments.
If node have loaded nf_defrag_ipv4 module but have no nf_conntrack_ipv4,
br_nf_pre_routing defragments incoming ipv4 fragments
but nfct check in br_nf_dev_queue_xmit does not allow re-fragment combined
packet back, and therefore it is dropped in br_dev_queue_push_xmit without
incrementing of any failcounters
It seems the only way to hit the ip_fragment code in the bridge xmit
path is to have a fragment list whose reassembled fragments go over
the mtu. This only happens if nf_defrag is enabled. Thanks to
Florian Westphal for providing feedback to clarify this.
Defragmentation ipv4 is required not only in conntracks but at least in
TPROXY target and socket match, therefore #ifdef is changed from
NF_CONNTRACK_IPV4 to NF_DEFRAG_IPV4
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Defrag user check in ip_expire was not updated after adding support for
"conntrack zones".
This bug manifests as a RFC violation, since the router will send
the icmp time exceeeded message when using conntrack zones.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ieee80211_reconfig already holds rtnl, so calling
cfg80211_sched_scan_stopped results in deadlock.
Use the rtnl-version of this function instead.
Fixes: d43c6b6 ("mac80211: reschedule sched scan after HW restart")
Cc: stable@vger.kernel.org (3.14+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add locked-version for cfg80211_sched_scan_stopped.
This is used for some users that might want to
call it when rtnl is already locked.
Fixes: d43c6b6 ("mac80211: reschedule sched scan after HW restart")
Cc: stable@vger.kernel.org (3.14+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 is notified about connection failures by
__cfg80211_connect_result() call. However, this
function currently does not free cfg80211 sme.
This results in hanging connection attempts in some cases
e.g. when mac80211 authentication attempt is denied,
we have this function call:
ieee80211_rx_mgmt_auth() -> cfg80211_rx_mlme_mgmt() ->
cfg80211_process_auth() -> cfg80211_sme_rx_auth() ->
__cfg80211_connect_result()
but cfg80211_sme_free() is never get called.
Fixes: ceca7b712 ("cfg80211: separate internal SME implementation")
Cc: stable@vger.kernel.org (3.10+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Filter out incoming multicast packages before applying their bitrate
to the rx bitrate station info field to prevent them from setting the
rx bitrate to the basic multicast rate.
Signed-off-by: Henning Rogge <hrogge@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building the name for the workqueue thread, make sure a format
string cannot leak in from the disk name.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The ubi->free_count should be updated with every insert/remove to/from
the ubi->free list.
Signed-off-by: Tanya Brokhman <tlinder@codeaurora.org>
Reviewed-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
In case of an error (if there are not free PEB's for example),
__wl_get_peb will return a negative value. In order to prevent access
violation we need to test the returned value prior to using it later on.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Reviewed-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Dan's "smatch" checker found out that there was a bug in the error path of the
'ubifs_remount_rw()' function. Instead of jumping to the "out" label which
cleans-things up, we just returned.
This patch fixes the problem.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Daniel Borkmann says:
====================
BPF cleanups
v3->v4:
- Sorry, noticed and fixed a typo in patch 3, rest as is
v2->v3:
- Included Dave's feedback for unsigned long type in patch 3
- Patch 1 and patch 2 unchanged since v1, dropped other
two for now
v1->v2:
- Only changed patch 5 as to suggestion from Alexei
- Rest is the same
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
