Change GPIO for any port
The set GPIO function should receive the port index to allow changing
the GPIO of another port. This is needed for the common init phase (one
the first driver is loaded for the chip)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause settings
- 1G pause was not working due to missing write to the emac block
(TX_MODE_FLOW_EN)
- The flow control should use the negotiated result (after autoneg) so
we should save both the requested autoneg and the result
- The HW credits with flow control at 1G speed were not optimized and
caused low throughput
- It is recommended to turn off flow control if the MTU is bigger than
5000B due to internal buffers size
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link order with external PHY
When external PHY exists (second chip with the PHY to translate to
another physical medium) the link with the eternal PHY and the network
should be established before setting the link between the 5771x and the
PHY. This is the right order and it is important when using autoneg -
the link to the network should use the autoneg and the link between the
two chips should be forced to the network result.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No LRO without Rx checksum
Disabling LRO when Rx checksum is disabled
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong structure size
The wrong structure was used in the sizeof to clear (luckily both
structures have the same size in this version...)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL capability
All designs reported WoL capability regardless of HW limitations - check
if this device is actually capable of WoL
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing MAC addresses filters
When the driver unloads, it should clear the MAC addresses filters in
the HW - this prevents packets from entering the chip when the driver is
re-loaded before initializing the right filters
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay in while loops
The delay in the loop should be after the change. This has very little
effect (can save one delay) but it is the right thing to do
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PBA Table Page Alignment Workaround
The PBA table starts on the middle of the page and that's causing very
low performance with virtualization. The solution is not to update via
the BAR directly but via chip access to the same memory
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Self-test false positive
- The memory test should use a mask according to the chip type
- In the register test, check the port only once and not inside the for
loop (not causing a failure - just ugly)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocation
- The CQE ring was allocated to the max size even for a chip that does
not support it. Fixed to allocate according to the chip type to save
memory
- The rx_page_ring was not freed on driver unload
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW attention lock
Making sure that only one function will handle the HW attention. This
makes the device parameter aeu_mask redundant so it is removed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW lock mechanism
Enhancing the HW lock to work per function and not only per port - this
is needed for the next patch that protects races over HW attention
detection between the different functions. At this chance, changing the
functions names to be more inline with the current naming convention
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
internal buffers must be cleared before the driver is loaded
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW Internal Memory structure
The FW uses data structures on the chip internal memory to aggregate the
connections when TPA is enabled. The driver was clearing the wrong offsets
and therefore one function could cause another function to loose packets.
Changing the initialization of the chip internal memory to clear only the
relevant memory for each function which is being loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics
- Making sure that each drop is accounted for in the driver statistics
- Clearing the FW statistics when driver is loaded to prevent
inconsistency with HW statistics
- Once error is detected (bnx2x_panic_dump), stop the statistics
before other actions (currently it is stopped last and can corrupt
the data) - Adding HW checksum error counter to the statistics
- Removing unused variable stats_ticks
- Using macros instead of magic numbers to indicate which statistics are
shared per port and which are per function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not dropping packets with L3/L4 checksum error
Those packets should be passed to the OS. The problem is clear in
forwarding mode.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW (bootcode) interface fixes
- Making sure that the device will not cause kernel panic of the
bootcode is corrupted or missing
- Removing module debug parameter "nomcp" since no one should work
without the bootcode (this is a left over from the chip bring up days)
- Instead of waiting fix amount of time for bootcode response, sample it
every 10ms (usually the answer is ready after less than 10ms)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dubious logical operation that was found by sparse:
linux-next-20080807/drivers/net/bnx2x_main.c:7205:27: warning: dubious: !x & y
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements all the quirk handling from the hci_usb driver to the
new btusb driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This removes the unnecessary ignore parameter, which is useless. There
are alternate methods of kicking a driver off an USB device.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use a single enum for managing modes, store supported modes by
the HW in a bitmask.
Register legacy rates with mac80211 only at init.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ath9k_tx_queue_info which contains the same elements,
and merge get/set functions of tx queue properties.
Also, fix whitespace damage in struct ath_softc.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.
Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new mac80211 11n ath9k Atheros driver. Only STA support
is currently enabled and tested.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove Atheros 11n devices from being claimed by ath5k as its
now handled by ath9k.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If you are using linked lists for queues list_splice() will not do what
you would expect even if you use the elements passed reversed. We need
to handle these differently. We add list_splice_tail() and
list_splice_tail_init().
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
these "magic" values must to be the other way round...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible for unsupported operating modes
to be accepted by the add_interface callback function.
This patch will block those modes until proper support
has been implemented for them.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following "mac80211: fix TX sequence numbers", if a packet
has the IEEE80211_TX_CTL_ASSIGN_SEQ assigned, a sequence number must be
supplied, either by hardware or software. AFAIK, no such hardware exists
for the p54, thus it must be done in software. With this patch, a connection
qith p54usb is stable, whereas the interface went off-line in 2-3 hours
without this change. Note that this code will have to be reworked for proper
sequence numbers on beacons. In addition, the sequence number has been placed
in the hardware state, not the vif state.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up iwl_tx_skb function.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is wrong to destroy a bonding master from a context that uses the sysfs
of that bond. When last IPoIB slave is unenslaved from by writing to a
sysfs file (for bond0 this would be /sys/class/net/bond0/bonding/slaves)
the driver tries to destroy the bond. This is wrong and can lead to a
lockup or a crash. This fix lets the bonding master stay and relies on
the user to destroy the bonding master if necessary (i.e. before module
ib_ipoib is unloaded)
This patch affects only bonds of IPoIB slaves. Ethernet slaves stay
unaffected.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Refactor mii monitor. As with the previous ARP monitor refactor,
the motivation for this is to handle locking rationally (in this case,
removing conditional locking) and generally clean up the code.
This patch breaks up the monolithic mii monitor into two phases:
an inspection phase, followed by an optional commit phase. The commit phase
is the only portion that requires RTNL or makes changes to state, and is
only called when inspection finds something to change.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some hardware set promisc when they are requested to set IFF_ALLMULTI flag.
It's ok, but if drivers set IFF_PROMISC flag when they set promisc,
it will broken upper layer handle for promisc and allmulti.
In addition, drivers can use their own hardware programming to make it.
So do not allow drivers to set IFF_* flags.
This is a general driver fix, so I didn't split it to pieces and send
to specific driver maintainers.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The dm9000 driver reads the chip's MAC address from the attached EEPROM. When
no EEPROM is present, or when the MAC address is invalid, it falls back to
reading the address from the chip.
This patch lets platform code set the desired MAC address through platform
data.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix possible bug where end of receive buffer could be overwritten.
The allocation needs to allow for the reserved space. This would only happen
if device received packet greater than Ethernet standard MTU.
Change this driver to use netdev_alloc_skb rather than setting skb->dev
directly. For the initial allocation it doesn't need to be GFP_ATOMIC.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reference: https://launchpad.net/bugs/140511
The Belkin bluetooth dongle unfortunately shares the vendor and device id
with the network adapter which causes lockups whenever the bluetooth
dongle is inserted.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_nic_pci_mem_read_direct':
drivers/net/netxen/netxen_nic_hw.c:1414: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'u64'
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_nic_pci_mem_write_direct':
drivers/net/netxen/netxen_nic_hw.c:1487: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'u64'
You don't know what type was used for u64 hence they cannot be printed without
casting.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix all errors and warnings reported by checkpatch.pl
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix all errors and warnings reported by checkpatch.pl
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
