Separate the TI OHCI OMAP1/2 host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Samsung OHCI EXYNOS host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the W90X900(W90P910) on-chip host controller driver from
ehci-hcd host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before W90X900(W90P910)
can be booted with a multi-platform kernel
and an ehci driver that only works on one of them.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the w90X900 bus glue.
This patch is rebased on greghk/usb-next 3.12 rc1.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DCD pin of the serial port can receive a PPS signal. By calling
the port line discipline dcd handle, this patch allow to monitor PPS
through USB serial devices.
However the performance aren't as good as the uart drivers, so
document this point too.
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the device receive a DCD status change, forward the signal to the
USB serial system. This way, we can detect, for instance, PPS pulses.
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_disconnect() no longer acquires usb_bus_list_lock, so update its
comment to that effect.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f5ea1100 cleans up the disk to host conversions for
node directory entries, but because a variable is reused in
xfs_node_toosmall() the next node is not correctly found.
If the original node is small enough (<= 3/8 of the node size),
this change may incorrectly cause a node collapse when it should
not. That will cause an assert in xfstest generic/319:
Assertion failed: first <= last && last < BBTOB(bp->b_length),
file: /root/newest/xfs/fs/xfs/xfs_trans_buf.c, line: 569
Keep the original node header to get the correct forward node.
(When a node is considered for a merge with a sibling, it overwrites the
sibling pointers of the original incore nodehdr with the sibling's
pointers. This leads to loop considering the original node as a merge
candidate with itself in the second pass, and so it incorrectly
determines a merge should occur.)
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
[v3: added Dave Chinner's (slightly modified) suggestion to the commit header,
cleaned up whitespace. -bpm]
After reports from Chris and Josh Boyer of a rare crash in applesmc,
Guenter pointed at the initialization problem fixed below. The patch
has not been verified to fix the crash, but should be applied
regardless.
Reported-by: <jwboyer@fedoraproject.org>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
of_get_display_timing(s) use of_find_node_by_name
to get child node, this is incorrect, of_get_child_by_name
should be used instead. The patch fixes it.
Small typo is also corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix to return -EINVAL when virtual vertical size smaller than real
instead of 0, as done elsewhere in this function. Also remove dup code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The nice thing about devm_* is that the driver doesn't need to free the
resources but the driver core takes care about that. This also
simplifies the error path quite a bit and removes the wrong check for a
clock pointer being NULL.
Russell King - ARM Linux <linux@arm.linux.org.uk>:
"And this patch also fixes the above: disabling/unpreparing _after_ putting
the thing - which was quite silly... :)"
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI-CM driver uses the backlight class so needs to build depend on it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
BIOS can mark a pin as "no physical connection" if the port is used by an
integrated display which is not audio capable. And audio driver will overlook
such pins.
On Haswell, such a disconneted pin will keep muted and connected to the 1st
converter by default. But if the 1st convertor is assigned to a connected pin
for audio streaming. The muted disconnected pin can make the connected pin
no sound output.
So this patch avoids using assigned converters for all unused pins for Haswell,
including the disconected pins.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently we assume that userspace will shut down the compressed stream
correctly. However, if userspcae dies (e.g. cplay & ctrl-C) we dont
stop the stream before freeing it.
This now checks that the stream is stopped before freeing.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 'e7f3880cd9b98c5bf9391ae7acdec82b75403776'
tty: Fix recursive deadlock in tty_perform_flush()
introduced a regression where tcflush() does not generate
SIGTTOU for background process groups.
Make sure ioctl(TCFLSH) calls tty_check_change() when
invoked from the line discipline.
Cc: stable@vger.kernel.org # v3.10+
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the STI driver by setting cpu_possible_mask to make EMEV2
SMP work as expected together with the ARM broadcast timer.
This breakage was introduced by:
f7db706 ARM: 7674/1: smp: Avoid dummy clockevent being preferred over real hardware clock-event
Without this fix SMP operation is broken on EMEV2 since no
broadcast timer interrupts trigger on the secondary CPU cores.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Trying to read data from the Pegasus Technologies NoteTaker (0e20:0101)
[1] with the Windows App (EasyNote) works natively but fails when
Windows is running under KVM (and the USB device handed to KVM).
The reason is a USB control message
usb 4-2.2: control urb: bRequestType=22 bRequest=09 wValue=0200 wIndex=0001 wLength=0008
This goes to endpoint address 0x01 (wIndex); however, endpoint address
0x01 does not exist. There is an endpoint 0x81 though (same number,
but other direction); the app may have meant that endpoint instead.
The kernel thus rejects the IO and thus we see the failure.
Apparently, Linux is more strict here than Windows ... we can't change
the Win app easily, so that's a problem.
It seems that the Win app/driver is buggy here and the driver does not
behave fully according to the USB HID class spec that it claims to
belong to. The device seems to happily deal with that though (and
seems to not really care about this value much).
So the question is whether the Linux kernel should filter here.
Rejecting has the risk that somewhat non-compliant userspace apps/
drivers (most likely in a virtual machine) are prevented from working.
Not rejecting has the risk of confusing an overly sensitive device with
such a transfer. Given the fact that Windows does not filter it makes
this risk rather small though.
The patch makes the kernel more tolerant: If the endpoint address in
wIndex does not exist, but an endpoint with toggled direction bit does,
it will let the transfer through. (It does NOT change the message.)
With attached patch, the app in Windows in KVM works.
usb 4-2.2: check_ctrlrecip: process 13073 (qemu-kvm) requesting ep 01 but needs 81
I suspect this will mostly affect apps in virtual environments; as on
Linux the apps would have been adapted to the stricter handling of the
kernel. I have done that for mine[2].
[1] http://www.pegatech.com/
[2] https://sourceforge.net/projects/notetakerpen/
Signed-off-by: Kurt Garloff <kurt@garloff.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `dma_set_coherent_mask':
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
Reviewed-and-tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not, the PHY will be active even the controller is not in use.
We find this issue due to the PHY's clock refcount is not correct
due to -EPROBE_DEFER return after phy's init.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It needs to free ci->hw_bank.regmap explicitly since it is not managed
resource.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clocksource devices provided by DT can be disabled (status != "okay").
Instead of registering clocksource drivers for disabled nodes, respect
the device's status by skiping disabled nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Some variants of Exynos MCT, namely exynos4210-mct at the moment, use
normal, shared interrupts for local timers. This means that each
interrupt must have correct affinity set to fire only on CPU
corresponding to given local timer.
However after recent conversion of clocksource drivers to not use the
local timer API for local timer initialization any more, the point of
time when local timers get initialized changed and irq_set_affinity()
fails because the CPU is not marked as online yet.
This patch fixes this by moving the call to irq_set_affinity() to
CPU_ONLINE notification, so the affinity is being set when the CPU goes
online.
This fixes a regression introduced by commit
ee98d27df6 ARM: EXYNOS4: Divorce mct from local timer API
which rendered all Exynos4210 based boards unbootable due to
failing irq_set_affinity() making local timers inoperatible.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This commit:
573145f08c
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
replaced a call to the driver's timer initialization by a call to
clocksource_of_init(). However, it failed to select CONFIG_CLKSRC_OF.
Fix this by selecting CONFIG_CLKSRC_OF for Armada370/XP machines.
Without this change the kernel is stuck at: 'Calibrating delay loop...'.
Signed-off-by: Jean Pihet <jean.pihet@linaro.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch straightens out some locking issues in the USB sysfs
interface:
Deauthorization will destroy existing configurations.
Attributes that read from udev->actconfig need to lock the
device to prevent races. Likewise for the rawdescriptor
values.
Attributes that access an interface's current alternate
setting should use ACCESS_ONCE() to obtain the cur_altsetting
pointer, to protect against concurrent altsetting changes.
The supports_autosuspend() attribute routine accesses values
from an interface's driver, so it should lock the interface
(rather than the usb_device) to protect against concurrent
unbinds. Once this is done, the routine can be simplified
considerably.
Scalar values that are stored directly in the usb_device structure are
always available. They do not require any locking. The same is true
of the cached interface string descriptor, because it is not
deallocated until the usb_host_interface structure is destroyed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When transfer type is isochronous, the other bits (bits 5..2) of
bmAttributes in endpoint descriptor might not be set zero. So it's better
to use usb_endpoint_type routine to mask bmAttributes with
USB_ENDPOINT_XFERTYPE_MASK to judge the transfter type later.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch is required to resolve remote wake issues with
certain devices.
Issue description:
If the remote wake is issued from the device in a specific timing
condition while the system is entering sleep state then it may cause
system to auto wake on subsequent sleep cycle.
Root cause:
Host controller rebroadcasts the Resume signal > 100 µseconds after
receiving the original resume event from the device. For proper
function, some devices may require the rebroadcast of resume event
within the USB spec of 100µS.
Workaroud:
1. Filter the AMD platforms with Yangtze chipset, then judge of all the usb
devices are mouse or not. And get out the port id which attached a mouse
with Pixart controller.
2. Then reset the port which attached issue device during system resume
from S3.
[Q] Why the special devices are only mice? Would high speed devices
such as 3G modem or USB Bluetooth adapter trigger this issue?
- Current this sensitivity is only confined to devices that use Pixart
controllers. This controller is designed for use with LS mouse
devices only. We have not observed any other devices failing. There
may be a small risk for other devices also but this patch (reset
device in resume phase) will cover the cases if required.
[Q] Shouldn’t the resume signal be sent within 100 us for every
device?
- The Host controller may not send the resume signal within 100us,
this our host controller specification change. This is why we
require the patch to prevent side effects on certain known devices.
[Q] Why would clicking mouse INTENSELY to wake the system up trigger
this issue?
- This behavior is specific to the devices that use Pixart controller.
It is timing dependent on when the resume event is triggered during
the sleep state.
[Q] Is it a host controller issue or mouse?
- It is the host controller behavior during resume that triggers the
device incorrect behavior on the next resume.
This patch sets USB_QUIRK_RESET_RESUME flag for these Pixart-based mice
when they attached to platforms with AMD Yangtze chipset.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch abstracts out a AMD chipset type which includes southbridge
generation and its revision. When os excutes usb_amd_find_chipset_info
routine to initialize AMD chipset type, driver will know which kind of
chipset is used.
This update has below benifits:
- Driver is able to confirm which southbridge generations and their
revision are used, with chipset detection once.
- To describe chipset generations with enumeration types brings better
readability.
- It's flexible to filter AMD platforms to implement new quirks in future.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Andiry Xu <andiry.xu@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like vbus, the dr_mode and phy_mode are also got from glue layer's
platform data or device node.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udc-core will call gadget's driver->disconnect, so we should avoid
calling gadget's disconnect again at ci_udc_stop in case the gadget's
unbind free some structs which is still used at gadget's disconnect.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, chipidea host has already depended on USB_EHCI_HCD
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for specifying soft dependencies in the modules themselves was
introduced in commit 7cb14ba.
In Arch we have always been shipping a module.d(5) fragment ordering ohci/uhci
after ehci. If this ordering is really necessary, it would be great to move it
to the kernel and getting the correct fragment generated by depmod.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP. The corresponding change has already
been made for ohci-hcd.
Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in ohci-hcd. The change is more
complicated than it was in ehci-hcd, because ohci-hcd doesn't scan for
isochronous completions in the same way as ehci-hcd does. Rather, it
depends on the hardware adding completed TDs to a "done queue". Some
OHCI controller don't handle this properly when a TD's time slot has
already expired, so we have to avoid adding such TDs to the schedule
in the first place. As a result, if the URB was submitted too late
then none of its TDs will get put on the schedule, so none of them
will end up on the done queue, so the driver will never realize that
the URB should be completed.
To solve this problem, the patch adds one to urb_priv->td_cnt for such
URBs, making it larger than urb_priv->length (td_cnt already gets set
to the number of TD's that had to be skipped because their slots have
expired). Each time an URB is given back, the finish_urb() routine
looks to see if urb_priv->td_cnt for the next URB on the same endpoint
is marked in this way. If so, it gives back the next URB right away.
This should be applied to all kernels containing commit 815fa7b917
(USB: OHCI: fix logic for scheduling isochronous URBs).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in uhci-hcd. It should be
applied to all kernels containing commit c44b225077 (UHCI: implement
new semantics for URB_ISO_ASAP).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
The same policy should be implemented in imx21-hcd, but I don't know
enough about the hardware to do it. As a second-best substitute, this
patch treats very late isochronous submissions as though the
URB_ISO_ASAP flag were set. I don't have any way to test this change,
unfortunately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's five bug fixes for 3.12.
The first two bugs fix issues with the command cancellation handling,
which can lead to oopses or the xHCI driver attempting to handle
previously-completed transfers. People have been running into oopses
and odd behavior with command cancellation for a couple kernel releases,
so they're marked for stable.
The third patch fixes an issue with USB remote wakeup under xHCI that
can only be reproduced under ChromeOS. As discussed, this fix is not
urgent, and isn't marked for stable.
The fourth patch fixes a race condition between URB cancellation and
userspace clearing an endpoint stall. The fifth patch removes some
annoying dmesg spam when a USB 3.0 device is disconnected, by avoiding
sending a Set SEL request.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSQOMcAAoJEBMGWMLi1Gc5504P/1vJY+iORn0iWcQfsZu4CmWQ
0ACJE4gWw0qonZyTsiU7/B7TveYTD2kSCvSjsWAiCMzcwEeIZRRujsDvBtXqk/Z4
4Bn0GgcCHMSq3DeNB/U23FSx/1SmUk6//vNFvDSo9pF3/qIJFnQu3L/eKoroq/Fg
jkkucDWEoNrlC1qcWCcB+20Yy4n0aCj19QXxmp3fH9qfTK+gkb0WnDzVKv3FrIpA
B453kOoNhghoMc1aqGRxBSeEoZBcd8jIFbQ3hSF5lG7dUN+J5GR7JWC0YxOGeVX3
5XcNbDZABnXZZV1+CcU7z6P2xaT1pwTKMi9gAWc2T5rxVQt1CPQICLLBwjLqkxKH
HcyHm7zSk/PTxeKXyj5Pp3h6we9mbPgHj8itUQ8j7ZqM+VgIj2/2HHxZJcgbfRCV
XPu5zZcDf294jqDR6pnaLkCZCkR/voHzqxARIP/koei0+0QTOKiJooZiK4ciuhCQ
uYWmAvCGreRCGFCdS94PVJxD9EM80sf1NbwCwnUYrS/MSMH9w/rW4ftKLNKkMRkT
xxXnogNIYR0iUX+dlrh3HGoU7GGjacxanbD8QS40JewE7IF1ds+4hOjXvNW26XNc
ylGjFqQq0qn2imST6l+gWePOE37BgdKwK5N5W66+leILLNXtytPx+IaUAZlwVNJB
gRoxqE4illdKf0pa6zqp
=ftVp
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2013-09-23' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Bug fixes for 3.12.
Hi Greg,
Here's five bug fixes for 3.12.
The first two bugs fix issues with the command cancellation handling,
which can lead to oopses or the xHCI driver attempting to handle
previously-completed transfers. People have been running into oopses
and odd behavior with command cancellation for a couple kernel releases,
so they're marked for stable.
The third patch fixes an issue with USB remote wakeup under xHCI that
can only be reproduced under ChromeOS. As discussed, this fix is not
urgent, and isn't marked for stable.
The fourth patch fixes a race condition between URB cancellation and
userspace clearing an endpoint stall. The fifth patch removes some
annoying dmesg spam when a USB 3.0 device is disconnected, by avoiding
sending a Set SEL request.
Sarah Sharp
Since commit b5dc0d10 (drm/imx: kill firstopen callback) the following probe
failure is seen:
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] No driver support for vblank timestamp query.
[drm] Initialized imx-drm 1.0.0 20120507 on minor 0
imx-ldb ldb.10: adding encoder failed with -16
imx-ldb: probe of ldb.10 failed with error -16
imx-ipuv3 2400000.ipu: IPUv3H probed
imx-ipuv3 2800000.ipu: IPUv3H probed
imx-ipuv3-crtc imx-ipuv3-crtc.0: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.0 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.1: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.1 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.2: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.2 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.3: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.3 failed with error -16
The reason for the probe failure is that now 'imxdrm->references' is incremented
early in imx_drm_driver_load(), so the following checks in imx_drm_add_crtc()
and imx_drm_add_encoder():
if (imxdrm->references) {
ret = -EBUSY;
goto err_busy;
}
,will always fail.
Instead of manually keeping the references in the imx-drm driver, let's use
drm->open_count.
After this patch, lvds panel is functional on a mx6qsabrelite board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't allow entry to iwctl_siwencodeext if device not open.
This fixes a race condition where wpa supplicant/network manager
enters the function when the device is already closed.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vt6656 is prone to resetting on the usb bus.
It seems there is a race condition and wpa supplicant is
trying to open the device via iw_handlers before its actually
closed at a stage that the buffers are being removed.
The device is longer considered open when the
buffers are being removed. So move ~DEVICE_FLAGS_OPENED
flag to before freeing the device buffers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There seems to be race condition that the device is ndo_start_xmit
at a point where the device is closing and apTD is NULL resulting
in dead lock.
Add a NULL check to apTD and return NULL to calling functions.
This is more likely on 64 bit systems.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking the return of dev_alloc_skb as stated in the following bug: https://bugzilla.kernel.org/show_bug.cgi?id=60411
Signed-off-by: Iker Pedrosa <ikerpedrosam@gmail.com>
Reported-by: RUC_Soft_Sec rucsoftsec@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The domain of Matt Mooneey's email doesn't exist anymore.
Setting usbip to Oprhan.
Signed-off-by: Tobias Polzer <tobias.polzer@fau.de>
Signed-off-by: Dominik Paulus <dominik.paulus@fau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
