Remove an extra variable 'queue' that already exists.
Also, since there are no code paths that use 'queue'
without intializing it, remove the unnecessary zero
initialization.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl7265D and iwl3168 are frozen on API version 29.
Set the MAX API allowed level to 29 from now on.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_mvm_sar_get_ewrd_table() In case of a BIOS bug, n_profiles
might be 0 thus we need to return an error value. Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Delete the scanned channel results.
No need in it we get it any way when logging.
The print only clogs up the ftrace print buffer.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While freeing inactive queue, check mvmsta to be valid before
dereferencing it. Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to have iwl_run_unified_mvm_ucode() be exposed
to other parts of the code since the logic to pick it over the
normal code in iwl_run_init_mvm_ucode() can just be done in
that function itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rates were changed to adapt to HE. Change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+cipAAoJEG4XJFUm622b+04H/2u7zhIqv3R5NsmGRlwjKmvd
6us1hcYzUiBW1kBFFtcvokwgqv3Rw/EUi+NYA5UCHgo30HTVJWTqW0q+BUEI7U0X
iwuFdHbs/qjj8hXKgZwaJMVyRhXAbq+iHYaMY5OEDNTRSbxqXA4V69SHGK9vLX0l
KQLJBZX3etnwsyRWrmd4E0roGGfD5tMPpGMUDSlvTPWt0I+1QFUxRI9ohn1fRBpD
p+UHHC+SYF6NzxvfqyPwm6ndb2XOwdAKYljlf4KrBwHtSXvAH8p5EASm4PjGbavY
0mrkv0cb8QOKQNVe9q4B4AmM4iAITZ9i3sQBPJ+EBN2P+kS/lFU5L/+5z3VQjms=
=KTEG
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
-----BEGIN PGP SIGNATURE-----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=f4VT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/net/wireless/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Kalle Valo <kvalo@codeaurora.org>
cc: linux-wireless@vger.kernel.org
cc: netdev@vger.kernel.org
update RF register 47 and 54 values according to vendor driver
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use register values from init LNA function instead of the ones from
restore LNA function. Apply register values based on rx path
configuration.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Somehow AP doesn't come up and the first scan fails if we don't do
VCO calibration every time.
The vendor driver duplicates the VCO calibration function into the
channel switching logic, we can do the same with less duplication.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The base value used for MT7620 differs from Rt5392 which resulted in
quite bad RX signal quality. Fix this by using the correct base value as
well as the LNA calibration values for HT20.
Reported-by: Tom Psyborg <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.12. Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
* Heavy work for the A000 device series;
* Some cleanup patches;
* A few fixes;
* Dynamic SAR support;
* Geographical SAR support;
* Support a few new PCI device IDs;
-----BEGIN PGP SIGNATURE-----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=ooBi
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-04-19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Another series of patches intended for v4.12. These are the changes:
* Heavy work for the A000 device series;
* Some cleanup patches;
* A few fixes;
* Dynamic SAR support;
* Geographical SAR support;
* Support a few new PCI device IDs;
When wifi is under scanning/linking/roaming, do not run the reset of the
coex mechanism because these activities are important for wifi, just run
the linking process and return.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For bt profiling, we do not need to limit the rx agg size.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Using macro to control the bt threshold.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check the bt rssi first and decrease it if the bt rssi is too high.
Then set the tdma and coex table.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use h2c to tell the firmware if the number of AP is more than 10 or
not.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Here we monitor one more wifi rssi to check the status of the network
and set the coex table instead of the legacy way.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For p2p/miracast, the wifi may have multiple ports for different roles.
Under this, we need extra settings for turning off the tdma and proper
coex table parameters.
We monnitor the number of links on a port to determine if it is for
p2p/miracast or not.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Monitor the rssi state to set the tdma and limit rx aggregation size to
fit the bt profiling.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix some ident and naming for linux coding style.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For bt a2dp, we need to check more rssi state combinations to have
better voice quality.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Let the wifi use main antenna to have higher power.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The threshold is used to adjust the base line for the rssi state.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use software dac swing and double check if it is sco_only to set the
tdma for voice quality.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1. Add more cases to adjust the wifi duration and add a case with
the max interval of 3 for some future uses.
2. rename tdma_adj -> ps_tdma_du_adj to indicate that this member is
for power saving tdma duration adjustment
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dac swing level should be an unsigned 32-bit value rather than
boolean.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Depending on the state of wifi, we need to set different tdma and coex
table parameters to make wfi and bt coexist smoothly. Otherwise the
bt may have low sound quality or mouse lag, which mean bad user
experience. The same problem may occur on wifi also, if could disconnect
or lose some important packets.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the wifi or bt has low rssi, they need extra parameter settings for
the tdma.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tune the wifi/bt slot time to get better performance.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register 0xcb4 determines if the PTA circuit can control the swtich
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of just setting the coex table directly, we check if the
wifi is under some important activity (scanning|roaming|linking) and
mark the packets as high priority in that case.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When wifi is at 5G band, it does not intefere with 2.4G bt signal,
hence we can just ignore it and transmit normally as nothing happened.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Monitor wifi status and check if it is changed.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Gather multiple coex table settings into a function coex_table_with_type()
and control the coex table according the type value as put in
switch-case expression.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The power_save_state function checks the state of power saving.
For tdma settings, the wifi sends nullfunc to pretend enter power saving
and then bt can transmit. Hence the coex needs to check the power status
before set the pstdma function.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Originally we only increase/decrease bt power in a fixed power gap, this
patch makes us be able to modify bt power for multiple power gaps and we
can precisely adjust the bt power.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function updates the information of bt profiling to help us decide
the network status and dispatch the resource properly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there are a lot of low-rate packets, then the connection of wifi is
unstable. If so, we should switch resource to bt to have a higher
transmission quality, or wifi resource will be wasted
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We monitor the packet counter to guess if the bt is slave or not, and
when bt is slave, it may receive packet at any time, so we will have to
take care about it
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larger packets have higher opportunity to be interrupt by bt signal.
In order to shorten the transmission time, control the packet
aggregation size.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'chan_stats' is (re)allocated in _mwifiex_fw_dpc() ->
mwifiex_init_channel_scan_gap(), which is called whenever the device is
initialized -- at probe or at reset.
But we only free it in we completely unregister the adapter, meaning we
leak a copy of it during every reset.
Let's free it in the shutdown / removal paths instead (and in the
error-handling path), to avoid the leak.
Ideally, we can eventually unify much of mwifiex_shutdown_sw() and
mwifiex_remove_card() (way too much copy-and-paste) to reduce the burden
on bugfixes like this. But that's work for tomorrow.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we shut down the device (i.e., during 'reset'), we cancel any
outstanding work, but we don't clear any work-related flags. This can
cause problems if, e.g., we begin to queue a new firmware dump or card
reset while the other one is in progress. That might leave work_flags
with a stale value, and we might begin one of these *after* we've
completely reset the device. That doesn't make sense, because all
firmware context will have been lost by then.
This fixes some forms of cascading failures, where I:
(a) force a firmware dump (cat /sys/kernel/debug/mwifiex/mlan0/device_dump)
(b) run a Wifi scan in parallel (iw mlan0 scan)
(c) the scan times out due to (a) hogging the interface
(d) the command timeout triggers another firmware dump and a reset [*]
(e) the 2nd firmware dump flag persists across the reset
(f) as soon as the interface comes back up, we trigger the pending
firmware dump
(g) subsequent commands time out again, while we are processing the
firmware dump; return to (d)
[*] Note that automatic card_reset() support is not yet implemented for
the mwifiex PCIe driver, so we won't hit *exactly* this behavior yet.
But we can see similarly-confusing behaviors today.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we reset because of a command timeout, we should reset this flag.
Otherwise, we might erroneously think the next command after reset is
timing out, and trigger another reset.
The above behavior effectively neuters the automatic card_reset()
behavior, as it means we will never recover from a command timeout
properly (and in fact, we might enter an infinite loop:
timeout -> reset -> (fake) timeout -> reset -> ...
This fixes a bug introduced with introduction of PCIe function level
reset support, but it was carried into the SDIO driver when it was
converted to use the same codepaths. And this is currently mostly a
problem only in the SDIO driver, because it's the only one with
automatic card_reset() support (e.g., on command timeout). But it will
be a problem for PCIe too, as I'm working on supporting automatic
card_reset() for PCIe.
Fixes: c742e623e9 ("mwifiex: sdio card reset enhancement")
Fixes: 4c5dae59d2 ("mwifiex: add PCIe function level reset support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Command buffers (skb's) are allocated by the main driver, and freed upon
the last use. That last use is often in mwifiex_free_cmd_buffer(). In
the meantime, if the command buffer gets used by the PCI driver, we map
it as DMA-able, and store the mapping information in the 'cb' memory.
However, if a command was in-flight when resetting the device (and
therefore was still mapped), we don't get a chance to unmap this memory
until after the core has cleaned up its command handling.
Let's keep a refcount within the PCI driver, so we ensure the memory
only gets freed after we've finished unmapping it.
Noticed by KASAN when forcing a reset via:
echo 1 > /sys/bus/pci/.../reset
The same code path can presumably be exercised in remove() and
shutdown().
[ 205.390377] mwifiex_pcie 0000:01:00.0: info: shutdown mwifiex...
[ 205.400393] ==================================================================
[ 205.407719] BUG: KASAN: use-after-free in mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie] at addr ffffffc0ad471b28
[ 205.419040] Read of size 16 by task bash/1913
[ 205.423421] =============================================================================
[ 205.431625] BUG skbuff_head_cache (Tainted: G B ): kasan: bad access detected
[ 205.439815] -----------------------------------------------------------------------------
[ 205.439815]
[ 205.449534] INFO: Allocated in __build_skb+0x48/0x114 age=1311 cpu=4 pid=1913
[ 205.456709] alloc_debug_processing+0x124/0x178
[ 205.461282] ___slab_alloc.constprop.58+0x528/0x608
[ 205.466196] __slab_alloc.isra.54.constprop.57+0x44/0x54
[ 205.471542] kmem_cache_alloc+0xcc/0x278
[ 205.475497] __build_skb+0x48/0x114
[ 205.479019] __netdev_alloc_skb+0xe0/0x170
[ 205.483244] mwifiex_alloc_cmd_buffer+0x68/0xdc [mwifiex]
[ 205.488759] mwifiex_init_fw+0x40/0x6cc [mwifiex]
[ 205.493584] _mwifiex_fw_dpc+0x158/0x520 [mwifiex]
[ 205.498491] mwifiex_reinit_sw+0x2c4/0x398 [mwifiex]
[ 205.503510] mwifiex_pcie_reset_notify+0x114/0x15c [mwifiex_pcie]
[ 205.509643] pci_reset_notify+0x5c/0x6c
[ 205.513519] pci_reset_function+0x6c/0x7c
[ 205.517567] reset_store+0x68/0x98
[ 205.521003] dev_attr_store+0x54/0x60
[ 205.524705] sysfs_kf_write+0x9c/0xb0
[ 205.528413] INFO: Freed in __kfree_skb+0xb0/0xbc age=131 cpu=4 pid=1913
[ 205.535064] free_debug_processing+0x264/0x370
[ 205.539550] __slab_free+0x84/0x40c
[ 205.543075] kmem_cache_free+0x1c8/0x2a0
[ 205.547030] __kfree_skb+0xb0/0xbc
[ 205.550465] consume_skb+0x164/0x178
[ 205.554079] __dev_kfree_skb_any+0x58/0x64
[ 205.558304] mwifiex_free_cmd_buffer+0xa0/0x158 [mwifiex]
[ 205.563817] mwifiex_shutdown_drv+0x578/0x5c4 [mwifiex]
[ 205.569164] mwifiex_shutdown_sw+0x178/0x310 [mwifiex]
[ 205.574353] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[ 205.580398] pci_reset_notify+0x5c/0x6c
[ 205.584274] pci_dev_save_and_disable+0x24/0x6c
[ 205.588837] pci_reset_function+0x30/0x7c
[ 205.592885] reset_store+0x68/0x98
[ 205.596324] dev_attr_store+0x54/0x60
[ 205.600017] sysfs_kf_write+0x9c/0xb0
...
[ 205.800488] Call trace:
[ 205.802980] [<ffffffc00020a69c>] dump_backtrace+0x0/0x190
[ 205.808415] [<ffffffc00020a96c>] show_stack+0x20/0x28
[ 205.813506] [<ffffffc0005d020c>] dump_stack+0xa4/0xcc
[ 205.818598] [<ffffffc0003be44c>] print_trailer+0x158/0x168
[ 205.824120] [<ffffffc0003be5f0>] object_err+0x4c/0x5c
[ 205.829210] [<ffffffc0003c45bc>] kasan_report+0x334/0x500
[ 205.834641] [<ffffffc0003c3994>] check_memory_region+0x20/0x14c
[ 205.840593] [<ffffffc0003c3b14>] __asan_loadN+0x14/0x1c
[ 205.845879] [<ffffffbffc46171c>] mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie]
[ 205.854282] [<ffffffbffc461864>] mwifiex_pcie_delete_cmdrsp_buf+0x94/0xa8 [mwifiex_pcie]
[ 205.862421] [<ffffffbffc462028>] mwifiex_pcie_free_buffers+0x11c/0x158 [mwifiex_pcie]
[ 205.870302] [<ffffffbffc4620d4>] mwifiex_pcie_down_dev+0x70/0x80 [mwifiex_pcie]
[ 205.877736] [<ffffffbffc1397a8>] mwifiex_shutdown_sw+0x190/0x310 [mwifiex]
[ 205.884658] [<ffffffbffc4606b4>] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie]
[ 205.892446] [<ffffffc000635f54>] pci_reset_notify+0x5c/0x6c
[ 205.898048] [<ffffffc00063a044>] pci_dev_save_and_disable+0x24/0x6c
[ 205.904350] [<ffffffc00063cf0c>] pci_reset_function+0x30/0x7c
[ 205.910134] [<ffffffc000641118>] reset_store+0x68/0x98
[ 205.915312] [<ffffffc000771588>] dev_attr_store+0x54/0x60
[ 205.920750] [<ffffffc00046f53c>] sysfs_kf_write+0x9c/0xb0
[ 205.926182] [<ffffffc00046dfb0>] kernfs_fop_write+0x184/0x1f8
[ 205.931963] [<ffffffc0003d64f4>] __vfs_write+0x6c/0x17c
[ 205.937221] [<ffffffc0003d7164>] vfs_write+0xf0/0x1c4
[ 205.942310] [<ffffffc0003d7da0>] SyS_write+0x78/0xd8
[ 205.947312] [<ffffffc000204634>] el0_svc_naked+0x24/0x28
...
[ 205.998268] ==================================================================
This bug has been around in different forms for a while. It was sort of
noticed in commit 955ab095c5 ("mwifiex: Do not kfree cmd buf while
unregistering PCIe"), but it just fixed the double-free, without
acknowledging the potential for use-after-free.
Fixes: fc33146090 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A separate wifi-only firmware was download during pcie function level
reset. It is in fact the tail part of wifi/bt combo firmware. Per
Brian's and Dmitry's suggestion, this patch extract the wifi part from
combo firmware.
After that, the mrvl/pcie8997_wlan_v4.bin image in linux-firmware repo
is redundant (though I guess we keep it around to support older
kernels).
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch correct pcie scratch register name, to keep the same with
chipset side definition.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_dbg will do nothing before adapter->dev get assigned. several logs
lost in this case. it can be avoided by fall back to pr_info.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If wakeup interrupt handler is called, we know that the wakeup
interrupt number is valid, there is no need to check it.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
nl80211 provides the NL80211_SCAN_FLAG_RANDOM_ADDR for every scan
request that should be randomized; the absence of such a flag means we
should not randomize. However, mwifiex was stashing the latest
randomization request and *always* using it for future scans, even those
that didn't set the flag.
Let's zero out the randomization info whenever we get a scan request
without NL80211_SCAN_FLAG_RANDOM_ADDR. I'd prefer to remove
priv->random_mac entirely (and plumb the randomization MAC properly
through the call sequence), but the spaghetti is a little difficult to
unravel here for me.
Fixes: c2a8f0ff9c ("mwifiex: support random MAC address for scanning")
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If iwl_pcie_ctxt_info_init_fw_sec() fails, the previous allocated DMA
memory needs to be freed (it even goes out of scope immediately.)
Do that to prevent the leak.
Fixes: eda50cde58 ("iwlwifi: pcie: add context information support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the context info fails to be allocated, the mutex
isn't unlocked properly, fix that.
Fixes: eda50cde58 ("iwlwifi: pcie: add context information support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When FW fails to get block ack, it will send the notification with
0 items in the TFD queue elements. Allow this and handle accordingly.
Fixes: c46e7724bf ("iwlwifi: mvm: support new BA notification response")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Memory offsets and lengths for A000 HW is different
than currently specified.
Fixes: e34d975e40 ("iwlwifi: Add a000 HW family support")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 CDB firmware, we cannot update phy context to a
different band - we must first remove it and add it
again. Support this flow for all a000 devices since
we may have various combinations that cause us to fail
regardless if CDB is active.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The notification infrastructure (iwl_notification_wait_*
functions) allows to wait until a list of notifications
will come up from the firmware and to run a special handler
(notif_wait handler) when those are received.
The operation mode notifies the notification infrastructure
about any Rx being received by the mean of
iwl_notification_wait_notify() which will do two things:
1) call the notif_wait handler
2) wakeup the thread that was waiting for the notification
Typically, only after those two steps happened, the
operation mode will run its own handler for the notification
that was received from the firmware. This means that the
thread that was waiting for that notification can be
running before the operation mode's handler was called.
When the operation mode's handler is ASYNC, things get even
worse since the thread that was waiting for the
notification isn't even guaranteed that the ASYNC callback
was added to async_handlers_list before it starts to run.
This means that even calling
iwl_mvm_wait_for_async_handlers() can't guarantee that
absolutely everything related to that notification has run.
The following can happen:
Thread sending the command Operation mode's Rx path
-------------------------- ------------------------
iwl_init_notification_wait()
iwl_mvm_send_cmd()
iwl_mvm_rx_common()
iwl_notification_wait_notify()
iwl_mvm_wait_for_async_handlers()
// Possibly free some data
// structure
list_add_tail(async_handlers_list);
schedule_work(async_handlers_wk);
// Access the freed structure
Split the 'run notif_wait's handler' and the 'wake up the
thread' parts to fix this. This allows the operation mode
to do the following:
Thread sending the command Operation mode's Rx path
-------------------------- ------------------------
iwl_init_notification_wait()
iwl_mvm_send_cmd()
iwl_mvm_rx_common()
iwl_notification_wait()
// Will run the notif_wait's handler
list_add_tail(async_handlers_list);
schedule_work(async_handlers_wk);
iwl_notification_notify()
iwl_mvm_wait_for_async_handlers()
This way, the waiter is guaranteed that all the handlers
have been run (if SYNC), or at least enqueued (if ASYNC)
by the time it wakes up.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently when rate isn't found (invalid rate or CCK rate in high
band) driver is assigning rate -1, which causes mac80211 to dump
it later with the cryptic rate value of 0xFF.
Instead, warn early and dump the frame in mvm.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 devices, we don't really have multi RX queue for now,
until we have the RX queue configuration API.
Disable RX queue notification for now.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we load firmware in extended mode (as we do by default for
now) driver should send a command what kind of commands ucode
should stop and wait for before proceeding with phy calibrations.
Support this command. Currently we only do NVM access - so mark
this bit only.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To utilize the maximum allowed tx power, an additional table was added
to the BIOS. The table consists of up to seven different regions
(currently only three are in use). Each region contains per band:
1. Maximum allowed tx power on the band.
2. Tx power offset for chain A.
3. Tx power offset for chain B.
On init flow driver reads this table by means of ACPI and
passes it to the firmware with GEO_TX_POWER_LIMIT cmd.
The firmware will use this table to enhance tx power with
the offset in the relevant table as well as verifying it does not
violate the maximum allowed tx power.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
API was changed once more to support 2 LMACs.
Adapt to change while preserving current functionality.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add one new PCI ID for the 8265 series.
Add three new PCI ID for the 8275 series.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the end, the firmware doesn't want the SP len as present
in the WMM IE, but rather the actual number of frames.
Fixes: bd3c6cf901a8 ("iwlwifi: mvm: tell the firmware about the U-APSD parameters")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get SN that is smaller than SSN of the aggregation,
we shouldn't apply any reordering on them.
Further more, HW NSSN will be zeroed, which can cause us
to make some invalid decisions.
Detect the situation and invalidate the BAID.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change the value of TX_CMD_SEC_KEY_FROM_TABLE flag
in TX_CMD security flags to accommodate a FW API change.
Bump min API for 9000 series devices to 30 to keep the driver aligned
aligned the FW.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Seems like HW is reversing addr3 in the MAC header of de-aggregated
AMSDU. Reverse it back.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This flag is used for mac80211 reordering. As we do reordering
ourselves, turning it on is misleading and pointless.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Not only that this write is not needed (as FW does this
itself), on newer HW this register is write protected
so trying to write there will cause problems.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In TVQM firmware returns the value of the queue ID and code
should accept it.
The TX queue config API was changed. Move to new API.
This has to be done in parallel in mvm and pcie.
Do not move yet to 512 queues since there are some opens
with enabling it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In TVQM mode the TX responses were changed to include
queue number since legacy TX queue number retrieval cannot
be scaled up to 512 queues.
Support this change.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In TVQM mode the queue ID is assigned after enablement.
Get rid of assuming pre-defined TX queue ID in functions
that will be used by TVQM allocation path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change queue allocation to be dynamic. On transport init only
the command queue is being allocated. Other queues are allocated
on demand.
This is due to the huge amount of queues we will soon enable (512)
and as a preparation for TX Virtual Queue Manager feature (TVQM),
where firmware will assign the actual queue number on demand.
This includes also allocation of the byte count table per queue
and not as a contiguous chunk of memory.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is basically the same as gen1, except for clean
ups of old devices configuration that are never used in a000
configuration.
It will also help with refactoring rf_kill later on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 transport we will allocate queues dynamically.
Right now queue are allocated as one big chunk of memory
and accessed as such.
The dynamic allocation of the queues will require accessing
the queues as pointers.
In order to keep simplicity of pre-a000 tx queues handling,
keep allocating and freeing the memory in the same style,
but move to access the queues in the various functions as
individual pointers.
Dynamic allocation for the a000 devices will be in a separate
patch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New transport will be used only by op modes that supports
buffer station offload - hence those will never be called.
Clean it up.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 devices we have 16 bytes for the TFD index and 16 for the
queue, in order to support 512 queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Code is basically the same, with a cleanups of old narrow host
command, ampg workarounds, some cosmetic stuff, and usage of
TFH functions when accessing TFD queues.
This enables also the cleanup of iwl_pcie_tfd_set_tb() since
now it won't be called anywhere in the a000 data path
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move to use the correct structure.
Remove code referring to old command.
Update DMA locations.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cleanup code that is irrelevant for a000 devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
By moving all the code that depends on the new API
we avoid unnecessary indentation in the code.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer firmware versions will be able to handle all the
WMM-PS flows internally when we act as a GO. The firwmare
relies on the fact that the drivers puts frames for
different peers in different queues (DQA) to achieve this.
The driver will not be aware of the power state of the peers
anymore.
Tell the firmware about the WMM-PS parameters of earch peer
that connects to us so that it can know what are the
trigger-enabled ACs, the delivery-enableds ACs and the
Service Period length.
This API change is backward compatible since older firmware
versions will simply ignore the newly added values.
Since we don't support ieee80211 TSPECs for now, just copy
the trigger-enabled ACs to the delivery enabled ones.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several occasions where a scan of the same type is requested
concurrently, so logging every time this happens is just noisy and
unnecessary. Remove the logging for these cases.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is just a copy-paste in order to make changes tracking
easier.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 FW moved to 15 as management TID.
The change for us is fairly local - translate old TID to 15
when enabling and disabling a queue, and make sure to cover
it also on TX responses.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
a000 devices queue management is going to change significantly.
We will have 512 queues. Those queues will be assigned number
by the firmware and not by the driver.
In addition, due to SN offload having TX queue shared between TIDs
is impossible
Also, the ADD_STA command no longer updates queues status.
The only point of changing queue in the SCD queue config API.
From driver perspective we have here a new design:
Queue sharing and inactivity checks are disabled.
Once this is done, the only paths that call scd_queue_cfg command
are paths that alloc and release TX queues - which will make future
accommodation to queue number assignment by FW easier.
Since allocating 512 queues statically is not advisable, transport
will allocate the queue on demand, fill the command with DRAM data
and send it. This is reflected in the new transport API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 devices the TX handling is different in a few ways:
* Queues are allocated dynamically
* DQA is enabled by default
* Driver shouldn't access TFH registers - ucode configures it
all in SCD_QUEUE_CFG command
Support all this in a new API with op mode, where op mode sends
the command, transport will allocate the queue dynamically, fill
in DMA properties, send the command to FW and get the ID back.
Current implementation only sets the new transport API and fills
the DMA properties.
Future patches will complete the other parts.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
