* Add IDE_HFLAG_NO_DSC host flag for hosts that doesn't support DSC overlap.
* Set it in aec62xx (for ATP850UF only) and hpt34x host drivers.
* Convert ide-tape device driver to check for IDE_HFLAG_NO_DSC flag.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename 'simplex_stat' variable to 'dma_stat' in ide_get_or_set_dma_base().
* Factor out code for forcing host out of "simplex" mode from
ide_get_or_set_dma_base() to ide_pci_clear_simplex() helper.
* Add IDE_HFLAG_CLEAR_SIMPLEX host flag and set it in alim15x3 (for M5229),
amd74xx (for AMD 7409), cmd64x (for CMD643), generic (for Netcell) and
serverworks (for CSB5) host drivers.
* Make ide_get_or_set_dma_base() test for IDE_HFLAG_CLEAR_SIMPLEX host flag
instead of checking dev->device (BTW the code was buggy because it didn't
check for dev->vendor, luckily none of these PCI Device IDs was used by
some other vendor for PCI IDE controller).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer needed assertion from amd74xx_probe().
* Factor out cable detection for AMD7409 to amd7409_cable_detect() and for
chipsets >= AMD7411 to amd7411_cable_detect().
* Use dev->vendor and dev->device instead of amd_config->udma_mask when
selecting cable detection method and checking for broken FIFO support in
init_chipset_amd74xx().
* Remove no longer needed AMD_BAD_FIFO define.
* Add 'swdma' parameter for setting .swdma_mask to DECLARE_AMD_DEV() macro.
* Add 'udma' parameter for setting .udma_mask to DECLARE_{AMD,NV}_DEV() macro.
* Keep a copy of a current amd74xx_chipsets[] entry in amd74xx_probe()
in order to fix ->swdma_mask on early AMD7409 revisions and ->udma_mask
on Serenade mainboards.
* Remove no longer needed fixups from init_chipset_amd74xx()
and AMD_CHECK_{SWDMA,SERENADE} defines.
* Move printing banner message from init_chipset_amd74xx() to amd74xx_probe(),
also remove incorrect comment while at it.
* Use hwif->ultra_mask instead of amd_config->udma_mask in amd_set_drive().
* Add 'udma_mask' argument to amd_set_speed() and pass UDMA mask from
amd_set_drive() instead of using amd_config->udma_mask.
* Move amd_config->base from AMD_* defines to users of these defines and add
0x40 the defined values. Then add amd_offset() inline helper for selecting
offset from 0x40 base (needed for nVidia controllers) and finally use it in
amd_set_speed(), amd7411_cable_detect() and init_chipset_amd74xx() instead
of amd_config->base.
* Remove no longer needed AMD_BAD_SWDMA define, ->{swdma,ultra}_mask setup
from init_hwif_amd74xx(), amd_{config,chipset} variables and amd_ide_chips
table.
* Fix init_chipset_amd74xx() comment.
* Bump driver version.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According to http://marc.info/?l=linux-ide&m=114346138611631, the drivers must
always register 8 DMA ports with ide_setup_dma(), so its last argument is not
needed. While at it, kill some useless parens in that function...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The TRM-290 chip is *not* SFF-8038i compatible and therefore can *not* call
ide_setup_dma() -- fix this and also cleanup the code a bit...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes from this.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE core supports dumping raw identify data in hdparm friendly format now
so verbose identify dumping in ide-{floppy,tape}.c device drivers (done iff
IDE{FLOPPY,TAPE}_DEBUG_INFO is defined to '1' and it is '0' by default)
is no longer nedeed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_dump_identify() debug helper for dumping raw identify data in
the hdparm friendly format (== the identify data can be extracted from
dmesg output and passed to hdparm --Istdin).
* Dump identify data in ide-probe.c::do_identify() if DEBUG is enabled.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Bump driver version.
* Remove filename and stale TODO from comments.
* Add my copyrights.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add 'rw' parameter to cdrom_read_check_ireason(), make it handle
both read and write checking, rename it to ide_cd_check_ireason(),
finally remove no longer needed cdrom_write_check_ireason().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add handling of fs read/write requests to cdrom_nepwc_intr()
and remove no longer needed cdrom_rw_intr().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In cdrom_newpc_intr():
* cleanup variables in the 'transfer data' loop
In cdrom_rw_intr():
* rename 'sectors_to_transfer' to 'thislen'
* rename 'this_transfer' to 'blen'
* keep number of bytes (instead of sectors) in 'thislen' and 'blen'
* call 'xferfunc' only once for 'blen'
* cache 'rq->buffer' in 'ptr' variable
* check for 'rq->bio' before setting 'ptr' and 'blen'
* check for 'ptr' instead of 'rq->current_nr_sectors'
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use the fact that for the first loop rq->current_nr_sectors is always
set and unify moving to the next buffer for read/write requests.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add handling of read requests to cdrom_start_write(), rename it
to cdrom_start_rw() and remove no longer needed cdrom_start_read().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add handling of write requests to cdrom_start_read_continuation(),
rename it to cdrom_start_rw_cont() and remove no longer needed
cdrom_start_write_cont().
* Remove redundant '(rq->sector & (sectors_per_frame - 1)' check.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add handling of read requests to cdrom_write_intr(), rename it
to cdrom_rw_intr() and remove no longer needed cdrom_read_intr().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_cd_drain_data() and use it in cdrom_{buffer_sectors,read_intr}()
(as a nice side-effect this cuts 0.5kB of code from ide-cd.o).
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add REQ_TYPE_{SENSE,ATA_PC} requests handling to cdrom_do_block_pc()
and remove cdrom_do_packet_command().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
cdrom_do_pc_continuation() is now identical to cdrom_do_newpc_cont()
so just always use the latter function.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add handling of REQ_TYPE_{SENSE,ATA_PC} requests to cdrom_newpc_intr()
(please note that these requests never have 'bio' attached to them
and they never use DMA), then remove no longer needed cdrom_pc_intr().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is no need for it anylonger and ide_set_handler() complains
if ->handler is not NULL anyway.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a preparation to move code handling cdrom.c IOCTLs out of ide-cd.c.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move lba_to_msf() and msf_to_lba() to <linux/cdrom.h>
(use 'u8' type instead of 'byte' while at it).
* Remove msf_to_lba() copy from drivers/cdrom/cdrom.c.
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ide-cd kernel module to ide-cd_mod in preparation to moving code out
from ide-cd.[c,h]. Add MODULE_ALIAS("ide-cd") to preserve compatibility.
* Move VERBOSE_IDE_CD_ERRORS code from ide-cd.[c,h] to ide-cd_verbose.c.
ide-cd_verbose.c is IDE subsystem independent and may be easily converted
into generic library usable by other drivers (i.e. libata) if needed.
* Add CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS config option to drivers/ide/Kconfig
replacing VERBOSE_IDE_CD_ERRORS define. Make this config option enabled by
default and visible only if CONFIG_EMBEDDED is defined.
before the patch:
text data bss dec hex filename
22841 360 1056 24257 5ec1 drivers/ide/ide-cd.o
after the patch w/ CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y:
text data bss dec hex filename
22857 360 1056 24273 5ed1 drivers/ide/ide-cd_mod.o
after the patch w/ CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=n:
text data bss dec hex filename
15091 360 1056 16507 407b drivers/ide/ide-cd_mod.o
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Coding style fixes for VERBOSE_IDE_CD_ERRORS code.
* Add KERN_{ERR,CONT} printk() levels where needed.
This is a preparation for moving this code out of ide-cd.[c,h].
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Re-organize handling of quirky devices:
* Add struct cd_list_entry, ide_cd_quirks_list[] and ide_cd_flags() helper.
* Set flags returned by ide_cd_flags() in ide_cdrom_setup().
* Add IDE_CD_FLAG_VERTOS_{300_SDD,600_ESD} and IDE_CD_FLAG_SANYO_3CD flags.
* Move device quirks from ide_cdrom_setup() to ide_cd_quirks_list[].
* Rename IDE_CD_FLAG_NEC260 to IDE_CD_FLAG_PRE_ATAPI12 and handle
quirky Stingray 8X CD-ROM using ide_cd_quirks_list[].
* Add IDE_CD_FLAG_FULL_CAPS_PAGE flag and handle quirky ACER 50X CD-ROM
/ WPI 32X CD-ROM using ide_cd_quirk_list[].
* Add IDE_CD_FLAG_PLAY_AUDIO_OK flag and handle quirky MATSHITA DVD-ROMs
using ide_cd_quirks_list[].
* Add IDE_CD_FLAG_LE_SPEED_FIELDS flag and handle quirky ACER/AOpen 24X
CD-ROM using ide_cd_quirk_list[].
* Fix some comments about quirky devices while at it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use BCD2BIN()/BIN2BCD() macros from <linux/bcd.h>
and remove the local bcd2bin()/bin2bcd() inlines.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove unused ->{writing,reserved} fields from struct ide_cd_config_flags.
* Move ->max_speed from struct ide_cd_config_flags to struct cdrom_info.
* Move ->current_speed from struct ide_cd_state_flags to struct cdrom_info.
* Add defines for config and state flags.
* Add 'unsigned int cd_flags' to struct cdrom_info and use ->cd_flags
instead of ->{config,state}_flags.
* Remove no longer needed struct ide_cd_{config,state}_flags.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it rename 'info' variable to 'cd' in
ide_cdrom_probe_capabilities() and ide_cdrom_setup().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use CDC_* flags directly and remove redundant flags from ->config_flags.
While at it:
* Add KERN_CONT to printk()-s in ide_cdrom_probe_capabilities().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
