t4_link_start() was completely misnamed. It does _not_ start up the
link. It merely does the L1 Configuration for the link. The Link Up
process is started automatically by the firmware when the number of
enabled Virtual Interfaces on a port goes from 0 to 1. So renaming
this routine to t4_link_l1cfg() for better documentation.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to flush the sge ec context cache, and utilize
this new function in the driver
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free VI interfaces in remove routine. If we don't do this then the
firmware will never drop the physical link to the peer.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SRIOV is enabled we need to be in VEB mode not VEPA mode at probe.
This fixes an NPAR bug when SRIOV is enabled in the BIOS.
Change-ID: Ibf006abafd9a0ca3698ec24848cd771cf345cbbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes a bug in the default configuration which
prevented a software bridge loaded on the PF interface from
working correctly because broadcast packets are incorrectly
looped back.
Fix the general case, by loading the driver in VEPA mode Until a
VF or VMDq VSI is added. This way loopback on the Main VSI is
turned off until needed and can resolve the issue of unnecessary
reflection for users that do not have VF or VMDq VSIs setup.
The driver must now coordinate the loopback setting for the Flow
Director (FDIR) VSI to make sure it is in sync with the current
VEB or VEPA mode setting.
The user can still switch bridge modes from the bridge commands and
choose to be in VEPA mode with VF VSIs. Because of hardware
requirements, the call to switch to VEB mode when no VF/VMDqs are
present will be rejected.
NOTE: This patch uses BIT_ULL as that is preferred going forward,
a followup patch in the lower priority queue to net-next will fix
up the remaining 1 << usages.
Change-ID: Ib121ddb18fe4b3c4f52e9deda6fcbeb9105683d1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethernet functionality is only available when working in ISSI > 0 mode.
Previously, the IB driver wasn't ready to work on that mode, and hence
building both the IB driver and the Ethernet functionality in the core
driver were disallowed by Kconfigs.
Now, once we have all the pre-steps in place, we can remove this limitation.
The last steps in the IB driver for getting that setup to work are:
create dummy SRQ for the driver's use (until now we could use XRC_SRQ
as SRQ and XRC_SRQ, after moving to ISSI > 0, we separate XRC SRQs from
basic SRQs) and adapt the create QP function to be compatible with ISSI > 0.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following helpers:
1. mlx5_query_port_proto_oper -- queries the port speed port mask
2. mlx5_query_port_link_width_oper - queries the port link with bitmask
3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port
These helpers will be used from the IB driver when working in ISSI > 0 mode.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, mlx5_query_port_ptys always queried port number one.
Added new argument in the function's prototype so we can also query
the second port. This will be needed when thr helper will be invoked
from the IB driver on non FPP (Function-Per-Port) devices.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the function prototypes for max and operational mtu to take the
local port number. In the Ethernet driver is this hard coded to one,
since ConnectX4 Ethernet devices are always function-per-port.
The IB driver also serves older devices (ConnectIB) which isn't such,
and hence the part can vary.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two wrapper functions to the query adapter command:
1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter.
2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the
query_adapter command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the implementation for the following commands:
1. QUERY_HCA_VPORT_GID
2. QUERY_HCA_VPORT_PKEY
3. QUERY_HCA_VPORT_CONTEXT
They will be needed when we move to work with ISSI > 0 in the IB driver too.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the vport header file to be under include/linux/mlx5, such that
the mlx5 IB can use it as well.
Also add nic_ prefix to the vport NIC commands to differeniate between
HCA vport commands and NIC vport commands.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The determination of the supported ISSI versions should be conditioned
on the returned mask, and not only on the return status of the query
ISSI command, fix that.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some core helper functions were named with mlx5_ only prefix, fix that to
mlx5_core_ so we're aligned with the overall scheme used for core services.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch afb736e933: "net/mlx5: Ethernet resource handling files"
from May 28, 2015, leads to the following static checker warning:
drivers/net/ethernet/mellanox/mlx5/core/en_flow_table.c:726 mlx5e_create_main_flow_table()
error: potential null dereference 'g'. (kcalloc returns null)
Fixes: afb736e933 ("net/mlx5: Ethernet resource handling files")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds full IPv6 addresses into flow_keys and uses them as
input to the flow hash function. The implementation supports either
IPv4 or IPv6 addresses in a union, and selector is used to determine
how may words to input to jhash2.
We also add flow_get_u32_dst and flow_get_u32_src functions which are
used to get a u32 representation of the source and destination
addresses. For IPv6, ipv6_addr_hash is called. These functions retain
getting the legacy values of src and dst in flow_keys.
With this patch, Ethertype and IP protocol are now included in the
flow hash input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVb1cPAAoJEG4XJFUm622bP0oIAKhUBlC3rtrOJd+9kREAGUJQ
Dk2xZr/p6hdb4dSHHKKroBr5mfryHknSs+AI5akJMph36DoBMD+Mwb4HlcL9cI5J
RXIjIvQEADsK+6ME7cqnw2htWlYsX8aJI96/2Eusveo/zHyAG3+eBC3wkyqWBlBK
EGV5ziClSe5pE5yGWj5tyr9me+qRQiO+dFJK1AoRE3Zq4pjj+5VDZoVQN0GNZGP7
lgeNOzvPxWt+ZseslP8IeCedN5c+NpacD889NnQJyMXaouSp7LmMod000bjnKK8o
9sRHsKxI5qHgC4mUa3Tk3cEnFqVYAo8KKOVaBVtKsMc4XoO/Qov6Z0AtXig5Xnk=
=CM/T
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================
Conflicts:
drivers/net/wireless/iwlwifi/Kconfig
Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ethtool get/set support for wake on lan, adapter doesn't support
it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in ethtool to dump loopback port statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in ethtool to dump adapter channel stats
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to get adapter specific hardware statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, two of the branches are dead code, since an earlier smaller
substring would have been found ("TP" in the "TP_NW" case and either
of "BNC" and "AUI" in the "BNC_AUI" case). Rearrange the strstr()
calls so that the longer strings are searched for first.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-06-03
This series contains updates to e1000e only.
Yanir provides 8 fixes and 1 version bump for e1000e. First fix resolves
a possible unit hang if multiple descriptors are available in the rings
during reset or runtime suspend. Fixed a warning on SPARC compile based
on a suggested solution from Alex Duyck. Fixed a logical error, where
a "if" condition under which a flush should occur, was revered. Fixed
a hardware issue that prevented i219 from working in legacy interrupts
mode. Fixed the hardware clock configuration and suprious non-linear
increment. Lastly, fixed a system hang which occurred during execution
of "ethtool -t <NIC>", by disabling MULR for the loopback test to avoid
the hand state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
fix typo in mlx4_set_vf_mac
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx4_enable_sriov is called by adapter without this
feature MLX4_DEV_CAP_FLAG2_SYS_EQS then during this path the function alloc
icm is called twice without freeing the structures from the first time.
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user loads mlx4_core with num_vfs greater than
supported then variable dev->dev_vfs is freed 2 times after unloading the
driver.
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code in drivers/net/ethernet/dec/tulip/uli526x.c
function "uli526x_timer":
1086 } else
1087 if ((tmp_cr12 & 0x3) && db->link_failed) {
[...snip...]
1109 }
1110 else if(!(tmp_cr12 & 0x3) && db->link_failed)
1111 {
[...snip...]
1117 }
1118 db->init=0;
is misleadingly indented: the
db->init=0
is indented as if part of the else clause at line 1086, but it is
independent of it (no braces before the "if" at line 1087).
This patch fixes the indentation to reflect the actual meaning of the code,
though is it actually meant to be part of the "else" clause? (I'm a
compiler developer, not a kernel person). It also adds spaces around
the assignment, to placate checkpatch.pl.
Seen via an experimental new gcc warning I'm working on for gcc 6,
-Wmisleading-indentation, using gcc r223098 adding
-Werror=misleading-indentation to KBUILD_CFLAGS in Makefile.
The experimental GCC emits this warning (as an error), rightly IMHO:
drivers/net/ethernet/dec/tulip/uli526x.c: In function ‘uli526x_timer’:
drivers/net/ethernet/dec/tulip/uli526x.c:1118:3: error: statement is
indented as if it were guarded by... [-Werror=misleading-indentation]
db->init=0;
^
drivers/net/ethernet/dec/tulip/uli526x.c:1086:4: note: ...this ‘else’
clause, but it is not
} else
^
Hope this is helpful
Dave
Signed-off-by: David Malcolm <dmalcolm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the time_after_eq macro for jiffies comparison operation
Signed-off-by: Antonio Murdaca <antonio.murdaca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_RFS_ACCEL or SMP aren't set, we fail to build, fix it.
Also, avoid build warning as of unused function on that setup.
Fixes: c66fa19c40 ('net/mlx4: Add EQ pool')
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump the version to reflect the driver changes and bug fixes for i219.
Also update the copyright, while we are at it.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
System would hang during execution of "ethtool -t <NIC>" for the same
reason that required flushing the descriptor rings. This fix disables
MULR for the loopback test to avoid the hang state.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Two issues involving systim were reported.
1. Clock is not running in the correct frequency
2. In some situations, systim values were not incremented linearly
This patch fixes the hardware clock configuration and the spurious
non-linear increment.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix handles a hardware issue that prevented i219 from
working in legacy interrupts mode (IntMode=0)
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The indication that a descriptor ring flush is required was read from
FEXTNVM7 by mistake. It should be read from the PCI config space.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The condition under which the flush should occur was reversed. The fix
should be applied before any HW reset (unless followed by bus reset)
and before any power state transition from D0.
If E1000_FEXTNVM7_NEED_DESCRING_FLUSH bit is set in FEXTNVM7 and TDLEN > 0
the Tx ring should be flushed. (fixes ~95% of the hang states).
If the E1000_FEXTNVM7_NEED_DESCRING_FLUSH did not clear, we should also
flush the RX ring. Bug was caught by Alexander Duyck during a code review
when examining this fix.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes a warning that was reported by Yanjiang Jin
<yanjiang.jin@windriver.com> by implementing the solution suggested by
Alexander Duyck <alexander.h.duyck@redhat.com>.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After testing various cases, the conclusion is that the fix MUST be
executed BEFORE any event that the HW is reset or transition to D3.
To fix that I moved the execution to the relevant places but per
Alexander Duyck's review, ensure now that the DMA is valid and was not
freed before manipulating the ring.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Unit hang may occur if multiple descriptors are available in the rings
during reset or runtime suspend. This state can be detected by testing
bit 8 in the FEXTNVM7 register. If this bit is set and there are pending
descriptors in one of the rings, we must flush them prior to reset. Same
applies entering runtime suspend.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Nothing in <asm/io.h> uses anything from <linux/vmalloc.h>, so
remove it from there and fix up the resulting build problems
triggered on x86 {64|32}-bit {def|allmod|allno}configs.
The breakages were triggering in places where x86 builds relied
on vmalloc() facilities but did not include <linux/vmalloc.h>
explicitly and relied on the implicit inclusion via <asm/io.h>.
Also add:
- <linux/init.h> to <linux/io.h>
- <asm/pgtable_types> to <asm/io.h>
... which were two other implicit header file dependencies.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Tidied up the changelog. ]
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Colin Cross <ccross@android.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Suma Ramars <sramars@cisco.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVbrcWAAoJEC0Llv5uNjIB/I8P/iY3Cz+1pZY8yPnHPIxzGh0Q
wGcZoiDGjVcblFkMzx9mvtMkBc/3Nb+e0UBKkzBH5DIwOHEum1Bf2fO+HQgKT4r+
xMD5vJ8dtpG++38UK90ouAW3UbSmcq21gUaKNZJtt6CThAuXuqtQthqrB+MC0L0p
VMix1+eY4MfsP6YKjszeLTro2RMjadKjGcmW5g1y5CI8yYyZIvN/J9m5Mdq9oixx
1RE8A7HNE6si22GUSuUm5l1Nb4kvCOsHvnERtMigy/lgsRyfVaKiwkFF9aEJRqpr
GxZ0yZivMVzi6cdx9wGZz0iTRAA+nwIjK5dUiHKTVrG/j4M0NFqTXHkJCR5T4wv0
Lsd8AT4d3u2ipu/g+pZhsMzhl2WPdoTfQWvN/iT4VBTYiZzAHaK9eOxa0Qn92NAR
uQAEx9bvF3mxfGTiL/E01DTd2CglxcQ8Xx/PPxrFR9X2xCD46o5t7z9KoZdLgK1z
0DZJ/EMjwYZnB/pepe2OyeGR34QLY83N/pJiUMLHoDL7tyc7Gu02RtQ6JxzMoqf3
K6G2QSbD33CBvUL/InmDgeNcGzrxle6jme7ErwKpa4AmgnYaMfL0fY9LU5OclKkr
87nrapL4WffopCP8eQNdu0oLP74IHFyePdt8+bgwqMK5iUVTBXPYepdCDAey3IWI
mv5621I/XDlg4nKO0fnL
=9GDL
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-06-03' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
After the new ciphers CCMP-256 and GCMP-128/256 were implemented,
wpa_supplicant could start negotiating them and use the software
implementation. This, however, breaks D3 behaviour in the driver
since it means that WoWLAN will not be possible.
To avoid breaking that feature, advertise only ciphers that the
hardware supports.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add DC2DC_CONFIG_CMD (0x83) cmd.
Add IWL_UCODE_TLV_CAPA_DC2DC_CONFIG_SUPPORT tlv.
The command allows the driver get & set the DCDC's frequency tune.
(freq_tune is the divider that is used to calculate the actual DCDC's
clock rate)
The command always returns the current/updated frequency tune values of
the DCDC.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmwares that used these commands is not supported
anymore. Remove them.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently, loading the firmware fails when it has higher API or CAPA
bits than the driver supports. That's an issue with integration.
At the same time, actually using api[0] and capa[0] will become
confusing when we also have api[1] and capa[1], and it's almost
certain that we'll mix up the bits and use the bits for api[1] with
api[0] by accident.
Avoid all this by translating the API/CAPA bits to the regular kernel
test_bit() format, and also providing wrapper functions. Also use the
__bitwise__ facility of sparse to check that we're testing the right
one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As pointed out by smatch, there's no need for a loop that always
immediately terminates. Use an if statement instead and while at
it clean up the mvmvif initialization.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the firmware is responsible for duration calculation, the
driver can easily support fast-xmit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the firmware is responsible for duration calculation, the
driver can easily support fast-xmit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As a preperation for multiple RX queues change the RBD
allocation model.
The new model includes a background allocator. The allocator is
called by the interrupt handler when there are two released
buffers by the queue, and the allocator starts allocating eight
pages per request.
When the queue has released 8 pages it tries claiming the
request. If the pages are not ready - it keeps claiming.
This new model should make sure that RBDs are always available
across the multiple queues.
The RBDs are transferred between the allocator and the queue.
The queue moves the free RBDs upon freeing them to the allocator.
The allocator moves them back to the queue's possession when the
request is claimed.
The allocator has an initial pool to make sure there are always RBDs
available for the request completion.
Release of the buffers at exit is done per pools - the allocator
frees its own initial pool and the queue frees its own pool.
Existing code refactor -
-Queue's initial pool is the size of the queue only as the allocation
of the new buffers no longer uses this pool.
-Removal of replenish background work, and replenish calls in the
interrupt handler and restock().
-The replenish() and the rxq used_list are used only during
initialization.
-Moved page allocation to a new function for code reuse.
New code -
Allocator code - new structure and functions.
Interrupt handler uses the allocator functions for replenishing buffers.
Reuse of the restock() method.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
On resume, all the interrupts are masked (CSR_INT_MASK is 0),
and ict is disabled.
Re-configure them both.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't use EBS for P2P find to make sure we find all GOs in
our only attempt.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently EBS status in scan complete notifications is set to
success if EBS wasn't activated. FW will add a special return
value for cases when EBS wasn't activated and we add a print
of this status.
This change is needed for debug only, no behavior changes.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow a cleaner way to access those hw-dependent registers,
instead of using the product family type etc.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This adds the MIPI mode type to the types declared supported
by the driver. Without this patch, when using MIPI mode and
looking at the logs the user would see the debug destination
"UNKNOWN".
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A minor refactoring for following patches.
This enables the reuse of the checks functions.
type=cleanup
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The variable translate is bool type. So assigning true instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently device dump generated in the driver is retrieved
using ethtool set/get dump commands. We will get rid of
ethtool approach and use devcoredump framework.
Device dump can be trigger by
cat /debugfs/mwifiex/mlanX/device_dump
and when the dump operation is completed, data can be read by
cat /sys/class/devcoredump/devcdX/data
We have prepared following script to split device dump data
into multiple files.
[root]# cat mwifiex_split_dump_data.sh
#!/bin/bash
# usage: ./mwifiex_split_dump_data.sh dump_data
fw_dump_data=$1
mem_type="driverinfo ITCM DTCM SQRAM APU CIU ICU MAC"
for name in ${mem_type[@]}
do
sed -n "/Start dump $name/,/End dump/p" $fw_dump_data > tmp.$name.log
if [ ! -s tmp.$name.log ]
then
rm -rf tmp.$name.log
else
#Remove the describle info "Start dump" and "End dump"
sed '1d' tmp.$name.log | sed '$d' > /data/$name.log
if [ -s /data/$name.log ]
then
echo "generate /data/$name.log"
else
sed '1d' tmp.$name.log | sed '$d' > /var/$name.log
echo "generate /var/$name.log"
fi
rm -rf tmp.$name.log
fi
done
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently we are dumping driver information also inside
firmware dump API. We will call it as device dump and
dump driver and firmware data separately.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Small letters are used in debug messages to match coding style
at other places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently we are dumping driver information only for SDIO
interface. This patch adds missing mwifiex_dump_drv_info()
call for PCIe interface.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As drv_info_dump pointer doesn't get reset, we may end up
freeing the allocated memory twice.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that firmware doesn't go back to normal
state when all firmware memories are dumped. As a result,
further commands are blocked. This happens due to missing
driver change of writing READ DONE to control register for
SDIO interface.
This patch adds a missing change to fix the problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If any VF is assigned as the PF is unloaded, do not attempt to
remove its vport or the vswitch. These will be removed if the
driver binds to the PF again, as an entity reset occurs during
probe.
A 'force' flag is added to efx_ef10_pci_sriov_disable() to
distinguish between disabling SR-IOV and driver unload.
SR-IOV cannot be disabled if VFs are assigned to guests.
If the PF driver is unloaded while VFs are assigned, the driver
may try to bind to the VF again at a later point if the driver
has been reloaded and the VF returns to the same domain as the PF.
In this case, the PF will not have a VF data structure, so the VF
can check this and drop out of probe early.
In this case, efx->vf_count will be zero but VFs will be present.
The user is advised to remove the VF and re-create it. The check
at the beginning of efx_ef10_pci_sriov_disable() that
efx->vf_count is non-zero is removed to allow SR-IOV to be
disabled in this case. Also, if the PF driver is unloaded, it
will disable SR-IOV to remove these unknown VFs.
By not disabling bus-mastering if VFs are still assigned, the VF
will continue to pass traffic after the PF has been removed.
When using the max_vfs module parameter, if VFs are already
present do not try to initialise any more.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver unloads, force the unbind and removal of any
VFs in the host with the PF. The PF cannot remove vports and
vswitches if they are still being used by a VF driver, and when
unloading the sfc driver the removal order is not guaranteed,
so the instruction from the PF to the VF to unbind enforces a
suitable ordering so that vswitches and vports can be removed.
As a result of this, manually unbinding the driver from a single
PF will result in all of its VFs in the host also being removed.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ifenslave command to set up a bond runs in an atomic
context, and it queries the stats on the devices that are
being enslaved. A VF needs to make an MCDI call to update
its stats, which is not allowed in atomic context.
The releasing of the stats_lock is moved to the beginning of
the VF stats update function so that in_interrupt() can be
used; it must be taken again before returning from this
function.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The raw_mask array is not initialised, so it needs to be
explicitly set to zero in the 'else' branch.
If the EVB capability is not present, a port cannot have multiple
functions so the per-port MAC stats are correct and should match
the corresponding vadaptor stats, so this redundancy can be
removed from the ethtool stats output.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC_CMD_MAC_STATS can be called on a function before a
vadaptor has been created, as the kernel can call into this
through ndo_get_stats/ndo_get_stats64.
If MC_CMD_MAC_STATS is called before the DMA queues have been
setup, so that a vadaptor has not been created yet, firmware
will return ENOENT. This is expected, so suppress the MCDI
error message in this case.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice statistics (in /proc/net/dev) are per-function
stats so they must use the vadaptor stats. Change the use of
MAC stats to vadaptor stats, and remove any statistics that
can only be measured per-port. All stats that are removed
will be shown as zeroes when these statistics are displayed.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware does not support a periodic DMA of vadaptor-stats
on VFs, so only update the stats buffer when stats are
requested (when running "ethtool -S" or an ip/ifconfig
command that reports stats).
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All interfaces will display vadaptor statistics, so set all the
relevant bits in the stats bitmask. Only functions with the
LINKCTRL flag will see other stats, including (per-port) MAC stats.
The vadaptor stats are from rx_unicast to tx_overflow.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port-id must be known so that the RMON level can be
set for the collection of vadapter stats.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC stats are per-port and will only be displayed on the PF
with control of the link (one per physical port). Vadapter stats
will also be displayed for this PF, so distinguish the MAC stats
by adding a prefix of "port_".
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On every adapter there will be one primary PF per adaptor and
one link control PF per port.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is a stylistic change and does not affect
functionality.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where we have multiple functions (PFs and VFs), this
sysfs entry is useful to identify the physical port corresponding
to the function we are interested in.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GFP_KERNEL should be used in the thread context
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to cast void* to u8*: pointer arithmetics
works same way for both.
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a copypaste bug that was discovered by a static analysis
tool:
The patch 4863dea3fa: "net: Adding support for Cavium ThunderX
network controller" from May 26, 2015, leads to the following static
checker warning:
drivers/net/ethernet/cavium/thunder/nicvf_ethtool.c:517
nicvf_set_rxfh()
warn: we tested 'hkey' before and it was 'false'
drivers/net/ethernet/cavium/thunder/nicvf_ethtool.c
506 /* We do not allow change in unsupported parameters */
507 if (hkey ||
^^^^
We return here.
508 (hfunc != ETH_RSS_HASH_NO_CHANGE && hfunc !=
ETH_RSS_HASH_TOP))
509 return -EOPNOTSUPP;
510
511 rss->enable = true;
512 if (indir) {
513 for (idx = 0; idx < rss->rss_size; idx++)
514 rss->ind_tbl[idx] = indir[idx];
515 }
516
517 if (hkey) {
^^^^
So this is dead code.
518 memcpy(rss->key, hkey, RSS_HASH_KEY_SIZE *
sizeof(u64));
519 nicvf_set_rss_key(nic);
520 }
521
522 nicvf_config_rss(nic);
523 return 0;
524 }
regards,
dan carpenter
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse messages like this:
drivers/net/ethernet/cavium/thunder/nicvf_main.c:1141:26: sparse: symbol
'nicvf_get_stats64' was not declared. Should it be static?
Also remove unused declarations
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They were left from development stage
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse message:
drivers/net/ethernet/cavium/thunder/nicvf_main.c:385:40: sparse: cast to
restricted __le64
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse message:
drivers/net/ethernet/cavium/thunder/nicvf_main.c:153:25: sparse: cast to
restricted __le64
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse messages like this:
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:897:24: sparse:
constant 0x300000000000 is so big it is long
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are duplicate NODE_ID macro definitions. Move all of them to
nic.h for usage in nic and bgx driver and introduce nic_get_node_id()
helper function.
This patch also fixes 64bit mask which should have been ULL by
reworking the node calculation.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The naming convention is to always have the flags prefixed with
IEEE80211_HW_ so they're 'namespaced', make this flag follow it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no drivers setting IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE
or IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE, so any code using the
two flags is dead; it's also exceedingly unlikely that any new driver
could ever need to set these flags.
The wcn36xx code is almost certainly broken, but this preserves the
previous behaviour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The process_mad device function declares some parameters as "in". Make those
parameters const and adjust the call tree under process_mad in the various
drivers accordingly.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds vnic driver register related changes for T6 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds NIC driver related changes for T6 adapter. Register related
changes, MC related changes, VF related changes, doorbell related
changes, debugfs changes, etc
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds new macro is_t6 and adds the register address range for T6 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various VTI tunnel (mark handling, PMTU) bug fixes from Alexander
Duyck and Steffen Klassert.
2) Revert ethtool PHY query change, it wasn't correct. The PHY address
selected by the driver running the PHY to MAC connection decides
what PHY address GET ethtool operations return information from.
3) Fix handling of sequence number bits for encryption IV generation in
ESP driver, from Herbert Xu.
4) UDP can return -EAGAIN when we hit a bad checksum on receive, even
when there are other packets in the receive queue which is wrong.
Just respect the error returned from the generic socket recv
datagram helper. From Eric Dumazet.
5) Fix BNA driver firmware loading on big-endian systems, from Ivan
Vecera.
6) Fix regression in that we were inheriting the congestion control of
the listening socket for new connections, the intended behavior
always was to use the default in this case. From Neal Cardwell.
7) Fix NULL deref in brcmfmac driver, from Arend van Spriel.
8) OTP parsing fix in iwlwifi from Liad Kaufman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
vti6: Add pmtu handling to vti6_xmit.
Revert "net: core: 'ethtool' issue with querying phy settings"
bnx2x: Move statistics implementation into semaphores
xen: netback: read hotplug script once at start of day.
xen: netback: fix printf format string warning
Revert "netfilter: ensure number of counters is >0 in do_replace()"
net: dsa: Properly propagate errors from dsa_switch_setup_one
tcp: fix child sockets to use system default congestion control if not set
udp: fix behavior of wrong checksums
sfc: free multiple Rx buffers when required
bna: fix soft lock-up during firmware initialization failure
bna: remove unreasonable iocpf timer start
bna: fix firmware loading on big-endian machines
bridge: fix br_multicast_query_expired() bug
via-rhine: Resigning as maintainer
brcmfmac: avoid null pointer access when brcmf_msgbuf_get_pktid() fails
mac80211: Fix mac80211.h docbook comments
iwlwifi: nvm: fix otp parsing in 8000 hw family
iwlwifi: pcie: fix tracking of cmd_in_flight
ip_vti/ip6_vti: Preserve skb->mark after rcv_cb call
...
Remove support for legacy ndo ops
.ndo_vlan_rx_add_vid/.ndo_vlan_rx_kill_vid. Rocker will use
bridge_setlink/dellink exclusively for VLAN add/del operations.
The legacy ops are needed if using 8021q driver module to setup VLANs on
the port. But an alternative exists in using bridge_setlink/delink to
setup VLANs, which doesn't depend on 8021q module. So rocker will switch
to the newer setlink/dellink ops. VLANs can added/delete from the port,
regardless if port is bridged or not, using the bridge commands:
bridge vlan [add|del] vid VID dev DEV self
(Yes, I agree it's confusing to use the "bridge" command to set a VLAN on a
non-bridged port).
Using setlink/dellink over legacy ops let's us handle the stacked driver
case automatically. It's built-in. setlink also pass additional flags
(PVID, egress untagged) that aren't available with the legacy ops.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the port joins a bridge, the port's internal VLAN ID needs to change
to the bridge's internal VLAN ID. Likewise, when leaving the bridge, the
internal VLAN ID reverts back the port's original internal VLAN ID. (The
internal VLAN ID is used by device to internally mark untagged pkts with
some VLAN, which will eventually be removed on egress...think PVID). When
the internal VLAN ID changes, we need to update the VLAN table entries and
the router MAC entries for IP/IPv6 to reflect the new internal VLAN ID.
This patch makes use of the common rocker_port_vlan_add/del functions to
make sure the tables are updated for the current internal VLAN ID.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On port probe, install by default untagged VLAN support. This is
equivalent to running the command:
bridge vlan add vid 0 dev DEV self
A user could, if they wanted, manaully removing untagged support from the
port by running the command:
bridge vlan del vid 0 dev DEV self
But installing it by default on port initialization gives the normal
expected behavior.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic house keeping: If there is an error adding the router MAC for this
vlan, removing the just installed VLAN table entry to leave device in same
state as before failure.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating the array of rocker port pointers, zero the array values so
we can test for !NULL to see if port is allocated/registered. We'll need
this later when installing untagged VLAN support for each port, during port
probe. It's a long story, but to install a VLAN (vid=0 for untagged, in
this case) on a port, we'll need to scan other ports to see if the VLAN
group for that VLAN has been setup. To scan the other ports, we need to
walk the port array.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused function cxgb4_enable_db_coalescing() and
cxgb4_disable_db_coalescing()
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rocker (switch) of a rocker_port may be trivially obtained from
the latter it seems cleaner not to pass the former to a function when
the latter is being passed anyway.
rocker_port_rx_proc() is omitted from this change as it is a hot path case.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver allocates one page for each buffer on the rx ring, which is
too much on architectures like ppc64 and can cause unexpected allocation
failures when the system is under stress. Now, we keep a memory pool
per queue, and if the architecture's PAGE_SIZE is greater than 4k, we
fragment pages and assign each 4k segment to a ring element, which
reduces the overall memory consumption on such architectures. This
helps avoiding errors like the example below:
[bnx2x_alloc_rx_sge:435(eth1)]Can't alloc sge
[c00000037ffeb900] [d000000075eddeb4] .bnx2x_alloc_rx_sge+0x44/0x200 [bnx2x]
[c00000037ffeb9b0] [d000000075ee0b34] .bnx2x_fill_frag_skb+0x1ac/0x460 [bnx2x]
[c00000037ffebac0] [d000000075ee11f0] .bnx2x_tpa_stop+0x160/0x2e8 [bnx2x]
[c00000037ffebb90] [d000000075ee1560] .bnx2x_rx_int+0x1e8/0xc30 [bnx2x]
[c00000037ffebcd0] [d000000075ee2084] .bnx2x_poll+0xdc/0x3d8 [bnx2x] (unreliable)
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dff173de84 ("bnx2x: Fix statistics locking scheme") changed the
bnx2x locking around statistics state into using a mutex - but the lock
is being accessed via a timer which is forbidden.
[If compiled with CONFIG_DEBUG_MUTEXES, logs show a warning about
accessing the mutex in interrupt context]
This moves the implementation into using a semaphore [with size '1']
instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/xen-netback/netback.c: In function ‘xenvif_tx_build_gops’:
drivers/net/xen-netback/netback.c:1253:8: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘int’ [-Wformat=]
(txreq.offset&~PAGE_MASK) + txreq.size);
^
PAGE_MASK's type can vary by arch, so a cast is needed.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
----
v2: Cast to unsigned long, since PAGE_MASK can vary by arch.
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been concerns that the function names gpiod_set_array() and
gpiod_get_array() might be confusing to users. One might expect
gpiod_get_array() to return array values, while it is actually the array
counterpart of gpiod_get(). To be consistent with the single descriptor API
we could rename gpiod_set_array() to gpiod_set_array_value(). This makes
some function names a bit lengthy: gpiod_set_raw_array_value_cansleep().
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some of of qca988x solutions are having global reset issue
during target initialization. Bypassing PLL setting before
downloading firmware and letting the SoC run on REF_CLK is fixing
the problem. Corresponding firmware change is also needed to set
the clock source once the target is initialized. Since 10.2.4
firmware is having this ROM patch, applying skip_clock_init only
for 10.2.4 firmware versions.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e, func, da;
@@
-init_timer (&e);
+setup_timer (&e, func, da);
-e.data = da;
-e.function = func;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e1, e2, e3, e4, a, b;
@@
-init_timer(&e1);
+setup_timer(&e1, a, b);
... when != a = e2
when != b = e3
-e1.function = a;
... when != b = e4
-e1.data = b;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e1, e2, e3, e4, a, b;
@@
-init_timer(&e1);
+setup_timer(&e1, a, b);
... when != a = e2
when != b = e3
-e1.data = b;
... when != a = e4
-e1.function = a;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e, func, da;
@@
-init_timer (&e);
+setup_timer (&e, func, da);
-e.data = da;
-e.function = func;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Rx packet data must be dropped, all the buffers
associated with that Rx packet must be freed. Extend
and rename efx_free_rx_buffer() to efx_free_rx_buffers()
and loop through all the fragments.
By doing so this patch fixes a possible memory leak.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
-----BEGIN PGP SIGNATURE-----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=KmwY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
As we get closer to the merge window, here are a few
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the current channel to 11. This is the default
value on reset.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CC2520 has the default 0dBm transmit power level on reset.
This patch update initial value of transmit power with 0dBm value.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for seeting tx power values for cc2520
and also for the combination of CC2520-CC2591.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes tha way of handling of cc2591-cc2520 combination
by moving amplified variable from platform data to private data.
This will be useful in other sections like tx power support.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initially we dont have the tx power settings from the user-space.
Now we have the support for seeting the tx power level.
So lets use the default tx power setting for the radio.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Atusb uses the at86rf231 transceiver so we can use the same calculation
for txpower settings for it.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this function we can set individual bits in the registers if needed.
With the old SR_VALUE macro we could only set one bit in the register
which was ok for some scenarios but not for all. With this subreg write
function we can now set more bits defined by the mask while not touching
the rest.
We start using it for the current SR_VALUE use case and will use it more
in upcoming patches.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Allocate the receive bufer from the NUMA node assigned to the primary
channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionnaly we may get oversized packets from the hardware which exceed
the nomimal 2KiB buffer size we allocate SKBs with. Add an early check
which drops the packet to avoid invoking skb_over_panic() and move on to
processing the next packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bcm_sysport_desc_rx() calls bcm_sysport_rx_refill() at the end of Rx
packet processing loop, after the current Rx packet has already been passed to
napi_gro_receive(). However, bcm_sysport_rx_refill() might fail to allocate a new
Rx skb, thus leaving a hole on the Rx queue where no valid Rx buffer exists.
To eliminate this situation:
1. Rewrite bcm_sysport_rx_refill() to retain the current Rx skb on the
Rx queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.
2. Modify bcm_sysport_desc_rx() to call bcm_sysport_rx_refill() at the
top of Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.
This is loosely inspired from d6707bec59 ("net: bcmgenet: rewrite
bcmgenet_rx_refill()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a 1:1 mapping between the software maintained control block in
priv->rx_cbs and the buffer address in priv->rx_bds, such that there is
no need to keep computing the buffer address when refiling a control
block.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug in the driver initialization causes soft-lockup if firmware
initialization timeout is reached. Polling function bfa_ioc_poll_fwinit()
incorrectly calls bfa_nw_iocpf_timeout() when the timeout is reached.
The problem is that bfa_nw_iocpf_timeout() calls again
bfa_ioc_poll_fwinit()... etc. The bfa_ioc_poll_fwinit() should directly
send timeout event for iocpf and the same should be done if firmware
download into HW fails.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver starts iocpf timer prior bnad_ioceth_enable() call and this is
unreasonable. This piece of code probably originates from Brocade/Qlogic
out-of-box driver during initial import into upstream. This driver uses
only one timer and queue to implement multiple timers and this timer is
started at this place. The upstream driver uses multiple timers instead
of this.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware required by bna is stored in appropriate files as sequence
of LE32 integers. After loading by request_firmware() they need to be
byte-swapped on big-endian arches. Without this conversion the NIC
is unusable on big-endian machines.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The thunderx ethernet driver fails to build on architectures
that do not have an atomic readq() and writeq() function for
64-bit PCI bus access:
drivers/net/ethernet/cavium/thunder/thunder_bgx.c: In function 'bgx_reg_read':
include/asm-generic/io.h:195:23: error: implicit declaration of function 'readq' [-Werror=implicit-function-declaration]
It seems impossible to get this driver to work on most 32-bit
hardware, so it's better to add an explicit dependency, in
order to let us keep building 'allmodconfig' kernels on
all architectures.
As the driver is meant for the internal hardware on an arm64 SoC, this
is not a problem for usability. Allowing the build on all 64-bit
architectures rather than just CONFIG_ARM64 on the other hand means that
we get the benefit of build testing on x86.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When freeing a CQ, we need to make sure there are no
asynchronous events (on the ASYNC EQ) that could
relate to this CQ before freeing it.
This is done by introducing synchronize_irq.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that EQs management is in the sole responsibility of mlx4_core,
the IRQ affinity hints configuration should be in its hands as well.
request_irq is called only once by the first consumer (maybe mlx4_ib),
so mlx4_en passes the affinity mask too late. We also need to request
vectors according to the cores we want to run on.
mlx4_core distribution of IRQs to cores is straight forward,
EQ(i)->IRQ will set affinity hint to core i.
Consumers need to request EQ vectors, according to their cores
considerations (NUMA).
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, mlx4_en allocated EQs and used them exclusively.
This affected RoCE performance, as applications which are
events sensitive were limited to use only the legacy EQs.
Change that by introducing an EQ pool. This pool is managed
by mlx4_core. EQs are assigned to ports (when there are limited
number of EQs, multiple ports could be assigned to the same EQs).
An exception to this rule is the ASYNC EQ which handles various events.
Legacy EQs are completely removed as all EQs could be shared.
When a consumer (mlx4_ib/mlx4_en) requests an EQ, it asks for
EQ serving on a specific port. The core driver calculates which
EQ should be assigned to that request.
Because IRQs are shared between IB and Ethernet modules, their
names only include the PCI device BDF address.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SRIOV, when simple (i.e - Ethernet L2 only) flow steering rules are
created, always create them at MLX4_DOMAIN_NIC priority (instead of
the real priority the function created them at). This is done in order
to let multiple functions add broadcast/multicast rules without
affecting other functions, which is necessary for DPDK in SRIOV.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-05-28
Here's a set of patches intended for 4.2. The majority of the changes
are on the 802.15.4 side of things rather than Bluetooth related:
- All sorts of cleanups & fixes to ieee802154 and related drivers
- Rework of tx power support in ieee802154 and its drivers
- Support for setting ieee802154 tx power through nl802154
- New IDs for the btusb driver
- Various cleanups & smaller fixes to btusb
- New btrtl driver for Realtec devices
- Fix suspend/resume for Realtek devices
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Ethernet part of the driver for the Mellanox ConnectX(R)-4
Single/Dual-Port Adapter supporting 100Gb/s with VPI. The driver
extends the existing mlx5 driver with Ethernet functionality.
This patch contains the driver entry points but does not include
transmit and receive (see the previous patch in the series) routines.
It also adds the option MLX5_CORE_EN to Kconfig to enable/disable the
Ethernet functionality. Currently, Kconfig is programmed to make
Ethernet and Infiniband functionality mutally exclusive.
Also changed MLX5_INFINIBAND to be depandant on MLX5_CORE instead of
selecting it, since MLX5_CORE could be selected without MLX5_INFINIBAND
being selected.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the resource handling files:
- flow_table.c: This file contains the code to handle the low level API
to configure hardware flow table. It is separated from
the flow_table_en.c, because it will be used in the
future by Raw Ethernet QP in mlx5_ib too.
- en_flow_table.[ch]: Ethernet flow steering handling. The flow table
object contain a mapping between flow specs and TIRs.
This mechanism will be used also to configure e-switch
in the future, when SR-IOV support will be added.
- transobj.[ch] - Low level functions to create/modify/destroy the
transport objects: RQ/SQ/TIR/TIS
- vport.[ch] - Handle attributes of a virtual port (vPort) in the
embedded switch. Currently this switch is a passthrough, until SR-IOV
support will be added.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
en_[rt]x.c contains the data path related code specific to tx or rx.
en_txrx.c contains data path code which is common for both the rx and
tx, this is mainly napi related code.
Below are the objects that are being used by the hardware and the driver
in the data path:
Channel - one channel per IRQ. Every channel object contains:
RQ - describes the rx queue
TIR - One TIR (Transport Interface Receive) object per flow type. TIR
contains attributes for a type of rx flow (e.g IPv4, IPv6 etc).
A flow is defined in the Flow Table.
Currently TIR describes the RSS hash parameters if exists and LRO
attributes.
SQ - describes the a tx queue. There is one SQ (Send Queue) per
TC (traffic class).
TIS - There is one TIS (Transport Interface Send) per TC. It
describes the TC and may later be extended to describe more
transport properties.
Both RQ and SQ inherit from the object WQ (work queue). This common code
to describe the layout of CQE's WQE's in memory is in the files wq.[cj]
For every channel there is one NAPI context that is used for RX and
for TX.
Driver is using netdev_alloc_skb() to allocate skb's.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce set/Query low level functions to access MTU in hardware. To be
used by the netdev.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce mlx5_core_modify_cq_moderation() to be used by the netdev, to
set hardware coalescing.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemet get/set port status low level functions to be exposed by the
netdev.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those registers will be used by the ethtool to set/get settings.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Query all supported types of dev caps on driver load.
- Store the Cap data outbox per cap type into driver private data.
- Introduce new Macros to access/dump stored caps (using the auto
generated data types).
- Obsolete SW representation of dev caps (no need for SW copy for each
cap).
- Modify IB driver to use new macros for checking caps.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_ifc.h was heavily modified here since it is now generated by a
script from the device specification (PRM rev 0.25). This specification
is backward compatible to existing hardware.
Some structures/fields were added here in order to enable the Ethernet
functionality of the driver.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for upcoming ethernet driver.
- Move msix array from eq_table struct to priv since its not related to
eq_table
- Intorduce irq_info struct to hold all irq information
- Move name from mlx5_eq to irq_info struct since it is irq property.
- Set IRQ affinity hints
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David Daney pointed in mlx4_core driver [1], mlx5_core is also
misusing the DMA-API.
This patch is removing the code that vmap() memory allocated by
dma_alloc_coherent().
After this patch, users of this drivers might fail allocating resources
on memory fragmeneted systems. This will be fixed later on.
[1] - https://patchwork.ozlabs.org/patch/458531/
CC: David Daney <david.daney@cavium.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-05-28
This series contains updates to ethtool, ixgbe, i40e and i40evf.
John adds helper routines for ethtool to pass VF to rx_flow_spec. Since
the ring_cookie is 64 bits wide which is much larger than what could be
used for actual queue index values, provide helper routines to pack a VF
index into the cookie. Then John provides a ixgbe patch to allow flow
director to use the entire queue space.
Neerav provides a i40e patch to collect XOFF Rx stats, where it was not
being collected before.
Anjali provides ATR support for tunneled packets, as well as stats to
count tunnel ATR hits. Cleaned up PF struct members which are
unnecessary, since we can use the stat index macro directly. Cleaned
up flow director ATR/SB messages to a higher debug level since they
are not useful unless silicon validation is happening.
Greg provides a patch to disable offline diagnostics if VFs are enabled
since ethtool offline diagnostic tests are not designed (out of scope)
to disable VF functions for testing and re-enable afterward. Also cleans
up TODO comment that is no longer needed.
Vasu provides a fix an FCoE EOF case where i40e_fcoe_ctxt_eof() maybe
called before i40e_fcoe_eof_is_supported() is called.
Jesse adds skb->xmit_more support for i40evf. Then provides a performance
enhancement for i40evf by inlining some functions which provides a 15%
gain in small packet performance. Also cleans up the use of time_stamp
since it is no longer used to determine if there is a tx_hang and was
a part of a previous tx_hang design which is no longer used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current algorithm for deciding on the number of VRSS channels is
not optimal since we open up the min of number of CPUs online and the
number of VRSS channels the host is offering. So on a 32 VCPU guest
we could potentially open 32 VRSS subchannels. Experimentation has
shown that it is best to limit the number of VRSS channels to the number
of CPUs within a NUMA node.
Here is the new algorithm for deciding on the number of sub-channels we
would open up:
1) Pick the minimum of what the host is offering and what the driver
in the guest is specifying as the default value.
2) Pick the minimum of (1) and the numbers of CPUs in the NUMA
node the primary channel is bound to.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethernet controller available in IPQ806x is a Synopsys DesignWare
Gigabit MAC IP core, already supported by the stmmac driver.
This glue layer implements some platform specific settings required to
get the controller working on an IPQ806x based platform.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case DT is used, this change adds the ability to the stmmac driver to
detect a fixed-link PHY, instanciate it, and use it during
phy_connect().
Fixed link PHYs DT usage is described in:
Documentation/devicetree/bindings/net/fixed-link.txt
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On stmmac driver, PHY specification in device-tree was done using the
non-standard property "snps,phy-addr". Specifying a PHY on a different
MDIO bus that the one within the stmmac controller doesn't seem to be
possible when device-tree is used.
This change adds support for the phy-handle property, as specified in
Documentation/devicetree/bindings/net/ethernet.txt.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two fixes which got lost in my recent distraction. One is a weird
cpumask function which needed to be rewritten, the other is a module
bug which is cc:stable.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wuP+
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull fixes for cpumask and modules from Rusty Russell:
"** NOW WITH TESTING! **
Two fixes which got lost in my recent distraction. One is a weird
cpumask function which needed to be rewritten, the other is a module
bug which is cc:stable"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
cpumask_set_cpu_local_first => cpumask_local_spread, lament
module: Call module notifier on failure after complete_formation()
This could lead userspace initram images getting
built without necessary firmware files included
leading to probing failures of ath10k on boot with
QCA61X4.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases some channel survey data was
reported incorrect.
Channel info events were expected to come in pairs
without and with COMPLETE flag set respectively
for each channel visit during scan.
The known deviation from this is rule for last
scan chan info and first (next) scan chan info
both have COMPLETE flag set. This was either
programmed with the intent of providing BSS cycle
count info or this is an artefact of firmware scan
state machine. Either way this is useless due to
short wraparound time, wraparound quirks and no
overflow notification.
Survey dumps now include only data gathered during
scan channel visits that can be computed
correctly.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When QCA988X cycle counter HW register wraps
around it resets to 0x7fffffff instead of 0. All
other cycle counter related registers are divided
by 2 so they never wraparound themselves. QCA61X4
has a uniform CC and it wraparounds in a regular
fashion though.
Worst case wraparound time is approx 24 seconds
(2**31 / 88MHz). Since scan channel visit times
are max 5 seconds (offchannel case) it is
guaranteed there's been at most 1 wraparound and
it is possible to compute survey active time
value. It is, however, impossible to determine the
point at which Rx Clear Count has been divided by
two so it is not reported upon wraparound.
This fixes some occasional incorrect survey data
on QCA988X as some channels (depending on how/when
scan/offchannel requests were requested) would
have approx 24 sec active time which wasn't
actually the case.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The macro isn't WMI specific. Instead it is
related to hardware chip so move the macro
accordingly. While at it document the magic value.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace confusing QL_STATUS_INVALID_PARAM == -1 == -EPERM with -EINVAL
and QLC_STATUS_UNSUPPORTED_CMD == -2 == -ENOENT with -EOPNOTSUPP, the
latter error code is arguable, but it is already used in the driver,
so let it be here as well.
Also remove always false (!buf) check on read(), the driver should
not care if userspace gets its EFAULT or not.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump.
Change-ID: I54ec2787a9fead5e18447078f26e5dd27f01da44
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver doesn't use the time_stamp member to determine if there is a
tx_hang any more. There really isn't any point to the variable at all
so just remove it. It was left over from a previous tx_hang design.
Change-ID: I4c814827e1bcb46e45118fe37acdcfa814fb62a0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Inlining these functions gives us about 15% more 64 byte packets per
second when using pktgen. 13.3 million to 15 million with a single
queue.
Also fix the function names in i40evf to i40evf not i40e while we are
touching the function header.
Change-ID: I3294ae9b085cf438672b6db5f9af122490ead9d0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric added support for skb->xmit_more in i40e, this ports that into
i40evf as well.
Support skb->xmit_more in i40evf is straightforward; we need to move
around i40e_maybe_stop_tx() call to correctly test netif_xmit_stopped()
before taking the decision to not kick the NIC.
Change-ID: Idddda6a2e4a7ab335631c91ced51f55b25eb8468
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These are not useful unless SV is happening as there is a FD flush counter
that tracks this.
Change-ID: If2655b5a29687247d03a51d35f69854bbeb711ce
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Because i40e_fcoe_ctxt_eof should never be called without
i40e_fcoe_eof_is_supported being called first, the EOF in fcoe_ctxt_eof
should always be valid and therefore we do not need to print an error
if it is not valid.
However, a WARN ON to easily catch any calls to i40e_fcoe_ctxt_eof that
aren't preceded with a call to i40e_fcoe_eof_is_supported is helpful.
Change-ID: I3b536b1981ec0bce80576a74440b7dea3908bdb9
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no need for a counter so remove the TODO comment.
Change-ID: I3321dda04934c4f5fda9b279ab666192bda44214
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can use the stat index macro directly, a variable is not required.
Change-ID: I19f08ac16353dc0cd87a1a8248d714e15a54aa8a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a 3rd dynamic filter counter to track Tunneled ATR hits separately.
Ethtool port stat "fdir_atr_tunnel_match"
Change-ID: Idd978b6db2a462b5722397cd2ffd04ef055f8655
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without this, RSS would have done inner header load balancing. Now we can
get the benefits of ATR for tunneled packets to better align TX and RX
queues with the right core/interrupt.
Change-ID: I07d0e0a192faf28fdd33b2f04c32b2a82ff97ddd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a HW recovery was started but not completed since all interfaces went
down, make sure to cleanup all interfaces before clearing the HW_RESTART
flag.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
BlockAck sessions can have events that are interesting to
debug. When we send or receive a BAR, it is may indicate
that something bad is happening. Even more so when mac80211
tells us that a frame timed out in the reodering buffer.
Add a few triggers for BlockAck session debugging.
Allow per-TID debugging.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
a lot of small fixes and cleanups, the bigger items are:
* proper mac80211 rate control locking, to fix some random crashes
(this required changing other locking as well)
* mac80211 "fast-xmit", a mechanism to reduce, in most cases, the
amount of code we execute while going from ndo_start_xmit() to
the driver
* this also clears the way for properly supporting S/G and checksum
and segmentation offloads
-----BEGIN PGP SIGNATURE-----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=oUlh
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-05-06' into iwlwifi-next
Lots of updates for net-next for this cycle. As usual, we have
a lot of small fixes and cleanups, the bigger items are:
* proper mac80211 rate control locking, to fix some random crashes
(this required changing other locking as well)
* mac80211 "fast-xmit", a mechanism to reduce, in most cases, the
amount of code we execute while going from ndo_start_xmit() to
the driver
* this also clears the way for properly supporting S/G and checksum
and segmentation offloads
Require the user to disable virtual functions before running the device
offline diagnostics. The offline diagnostics are intended to ensure
basic operation of the device - it is beyond the scope of the diagnostic
test to handle the additional complexity of bringing all the virtual
functions offline and then back online for each test run.
Change-ID: Ic0b854851a09fc85df0c9e82c220e45885457c30
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When PFC is enabled for any UP in single TC configuration the driver didn't
collect the PFC XOFF RX stats. Though a single TC with PFC enabled is not a
common scenario do not prevent the driver from collecting stats if firmware
indicates that PFC is enabled.
Change-ID: Ie20bd58b07608b528f3c6d95894c9ae56b00077a
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For UMAC, we were not treating a race condition that happens in the
scan flows, because it was not using the same state flags. Now that
UMAC and LMAC scans use the same state flags, we can also handle the
race conditions for UMAC.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
UMAC scans now use the general scan status for almost everything, the
only part missing was in the scan complete notifications. Change it
to use the stopping flags instead of clearing the flags when the stop
comes from above and clean the handler function a bit.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The regular and scheduled scan functions are very similar, so they can
be combined into one.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Having explicit rx cmd header fields is useful, as it can
be used for event filtering (e.g. saving only debug logs,
rather than the whole data)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This check for family type is redundant as the if clause above
checks a family-dependent Boolean (which is not set for family 8000 anyway).
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The UMAC and LMAC scan_stop functions are now nearly identical, so
they can be combined into a single function instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We can only have one scan per type at the same time, so the code that
tries to stop several scans of a type is unnecessary. Remove that to
reduce code complexity.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We can only have one scan of each type running at the same time, so we
can remove one attribute in the UID information we save. We had array
index, UID and type, but only UID (== array_index) and type are
necessary. Refactor the code to use this simplified array.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for scan priority API with 8 levels instead of the
existing 3 levels. This API is needed to define the priority of
new ooc activities, e.g. gscan.
Add a TLV flag to indicate if the new API is supported so that
devices that does not support the new API will continue to use
the old one.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some LMAC specific functions had too generic names
(i.e. *_scan_offload_*) and were hard to distinguish from functions
that are really generic. Rename these functions to *_lmac_scan_* in
to make it more consistent and easier to read.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For consistency with the LMAC functions, rename the UMAC scan stop
function to iwl_mvm_umac_scan_stop(). Additionally, move things
around a bit to avoid an unnecessary forward declaration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For UMAC scans, we were simply jumping into another function when scan
stop functions were called, while for LMAC scans, the flow continued.
To make the flows cleaner and more balanced, combine the UMAC part
into the main stop functions. This also makes us take one step closer
into combining the state flags for both APIs.
Note that some STOPPING flags will be dangling in UMAC scans, but it
doesn't matter because they are not used in UMAC yet (and this will be
fixed in subsequent patches).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It is not necessary to stop regular scans when going out of idle
state. Previously, we were doing so for LMAC scans because the
iwl_mvm_scan_offload_stop() function was stopping both kinds of scans.
Now that we have more granularity, we can skip it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The iwl_mvm_scan_offload_stop() function is used to stop LMAC regular
scan, stop LMAC scheduled scan and stop UMAC scheduled scans (but not
UMAC regular scans), making it very difficult to read.
Reorganize the scan stopping functions by creating separate functions
to stop regular and scheduled scans, separating the LMAC stopping part
of the code from the rest and renaming the offload_stop function to
iwl_mvm_lmac_scan_stop().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The commit below fixed this for the old firmware API only.
Since the new firmware API hasn't been released yet, this
doesn't fix anything on currently existing firmwares.
This completes:
commit afcee962b0
Author: Eyal Shapira <eyal@wizery.com>
Date: Mon Feb 9 15:18:17 2015 +0200
iwlwifi: mvm: fix BT coex shared antenna activity check
type=bugfix
bug=not-tracked
fixes=unknown
Reviewed-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The iwl_mvm_config_sched_scan_profiles() function is only used in
scan.c, so remove the declaration from mvm.h and make it static.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After the scan refactor, the order of the SSIDs passed to the firmware
in all scans (including net-detect) are inverted. This was causing
the reporting code to use the wrong SSIDs. To fix this, invert the
array index when accessing the saved match SSIDs to report the
wake-up.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add UMAC scan iteration complete notification. This notification can
be enabled by setting scan_iter_notif_enabled through debugfs.
Upon receiving this notification, print the list of channels that
have been scanned in this iteration. This is useful for debugging.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When receiving scan iteration complete notification, print a list of
the channels that have been scanned in this iteration.
This is useful for debugging.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The BT_CONFIG command used to be very long, hence it was
allocated on the heap in the previous API. In the new API,
this command is much smaller, and can now safely be
allocated on the stack.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since we don't need to configure the Ack / CTS kill mask
anymore in the new API, we don't need to iterate all the
interfaces upon rssi event on one of the interfaces.
Remove that code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no need to have separate definitions for the UMAC scan types,
since they are the same as the LMAC types. Remove UMAC scan types and
use the generic ones instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to imeplement the extended VI session feature for Miracast, the FW
requires to detect the VI queue. The detection of the VI queue is done when
it is assigned to a STA with ADD_STA command, so by this time the FW expects
the queue to be already configured (mapped to VI AC and aggregation enabled).
Previously, the queue configuration was done after STA modificaton which
broke the extended VI session feature and resulted in higher latencies.
Fix this by calling iwl_mvm_enable_agg_txq before station modification.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the device fails to start correctly prior to loading the
regular runtime firmware (after having run the INIT firmware),
treat that error correctly by actually checking the return
value of _iwl_trans_start_hw() and stopping the device again
before returning an error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to the nl80211 documentation, we can neither advertise
scheduled scan nor netdetect address randomisation. However, all
the products that currently require this don't have a need for
the full randomisation.
Therefore, advertise the feature anyway which results in host-
based randomisation, done whenever the system suspends. This is
sufficient for the platforms currently requiring this feature.
If we ever extend this in the future to do full randomisation in
the firmware, then certainly this will still be sufficient for
the current requirements, so it doesn't make a lot of sense to
split the feature bits.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set a default NVM in case the userspace specifies a file
that doesn't match the hardware version. This allows not
to change the boot scripts when someone replaces the device
with a newer hardware step.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add debugfs entry for showing the different Tx power restrictions that are
caused due to various reasons.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Flow director is exported to user space using the ethtool ntuple
support. However, currently it only supports steering traffic to a
subset of the queues in use by the hardware. This change allows
flow director to specify queues that have been assigned to virtual
functions by partitioning the ring_cookie into a 8bit VF specifier
followed by 32bit queue index. At the moment we don't have any
ethernet drivers with more than 2^32 queues on a single function
as best I can tell and nor do I expect this to happen anytime
soon. This way the ring_cookie's normal use for specifying a queue
on a specific PCI function continues to work as expected.
CC: Alex Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The transport modules all need to allocate memory and set up
certain values. Refactor that code into a new common function
to share it and to simplify the error handling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The UMAC API supports multiple scan schedules, but now we use only a
single one. Change the comment to make this clear and avoid
confusion.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This removes the use of the two deprecated calls to the
macro PTR_RET in iwl_mvm_get_regdomain and replaces them
both to PTR_ERR_OR_ZERO.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
[Commit message editing]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The radio cfg DWORD was taken from the wrong place in the
8000 HW family, after a line in the code was wrongly changed
by mistake. This broke several 8260 devices.
Fixes: 5dd9c68a85 ("iwlwifi: drop support for early versions of 8000")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The cmd_in_flight tracking was introduced to workaround faulty
power management hardware, by having the driver keep the NIC
awake as long as there are commands in flight. However, some of
the code handling this workaround was unconditionally executed,
which resulted with an inconsistent state where the driver assumed
that the NIC was awake although it wasn't.
Fix this by renaming 'cmd_in_flight' to 'cmd_hold_nic_awake' and
handling the NIC requested awake state only for hardwares for
which the workaround is needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Platform NVRAMs often contain values with spaces. Even if right now most
firmware-supported entries are simple values, we shouldn't reject these
with spaces. It was semi-confirmed by Broadcom in the early patch adding
support for platform NVRAMs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes brcmfmac dealing with NVRAM coming from platform e.g. from a
flash MTD partition. In such cases entries are separated by \0 instead
of \n which caused ignoring whole content after the first "comment".
While platform NVRAM doesn't usually contain comments, we switch to
COMMENT state after e.g. finding an unexpected char in key name.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With a simple use of snprintf and small buffer we can compare NVRAM
entry value with a full string. This way we avoid checking random chars
at magic offsets.
Tested on BCM43602 with NVRAM hacked to use v1 format.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Comparing NVRAM entry with a full filtering string is simpler than
comparing it with a short prefix and then checking random chars at magic
offsets. The cost of snprintf relatively low, we execute it just once.
Tested on BCM43602 with NVRAM hacked to use V2 format.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for the simplest of MediaTek Wi-Fi devices - MT7601U.
It is a single stream bgn chip with no bells or whistles.
This driver is partially based on Felix's mt76 but IMHO it doesn't
make sense to merge the two right now because MT7601U is a design
somewhere between old Ralink devices and new Mediatek chips. There
wouldn't be all that much code sharing with the devices mt76 supports.
Situation may obviously change when someone decides to extend m76 with
support for the more recent USB dongles.
The driver supports only station mode. I'm hoping to add AP support
when time allows.
This driver sat on GitHub for quite a while and got some testing there:
http://github.com/kuba-moo/mt7601u
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The fields of struct acpi_device are only known when CONFIG_ACPI is
defined. Fix this by using a helper function. This will resolve the
issue found in linux-next:
../brcmfmac/bcmsdh.c: In function 'brcmf_ops_sdio_probe':
../brcmfmac/bcmsdh.c:1139:7: error: dereferencing pointer to incomplete type
adev->flags.power_manageable = 0;
^
Fixes: f0992ace68 ("brcmfmac: prohibit ACPI power management ...")
Cc: Fu, Zhonghui <zhonghui.fu@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
da91309e0a (cpumask: Utility function to set n'th cpu...) created a
genuinely weird function. I never saw it before, it went through DaveM.
(He only does this to make us other maintainers feel better about our own
mistakes.)
cpumask_set_cpu_local_first's purpose is say "I need to spread things
across N online cpus, choose the ones on this numa node first"; you call
it in a loop.
It can fail. One of the two callers ignores this, the other aborts and
fails the device open.
It can fail in two ways: allocating the off-stack cpumask, or through a
convoluted codepath which AFAICT can only occur if cpu_online_mask
changes. Which shouldn't happen, because if cpu_online_mask can change
while you call this, it could return a now-offline cpu anyway.
It contains a nonsensical test "!cpumask_of_node(numa_node)". This was
drawn to my attention by Geert, who said this causes a warning on Sparc.
It sets a single bit in a cpumask instead of returning a cpu number,
because that's what the callers want.
It could be made more efficient by passing the previous cpu rather than
an index, but that would be more invasive to the callers.
Fixes: da91309e0a
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (then rebased)
Tested-by: Amir Vadai <amirv@mellanox.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Acked-by: David S. Miller <davem@davemloft.net>
This patch changes variable name 'fn' to 'pf' of structure adapter.
A 'fn' usually stands for PCI function which could be a PF or a VF.
However, the use of this particular variable is explicitly limited to PF
only. So, be specific about it in the variable name.
Also corrects arguments passed for fn t4_ofld_eq_free, t4_ctrl_eq_free,
t4_eth_eq_free, t4_iq_free, t4_alloc_vi, t4_fw_hello, t4_wr_mbox and
t4_cfg_pfvf function.
Also renames cxgb4_t4_bar2_sge_qregs to t4_bar2_sge_qregs and renames
the latter function name in cxgb4vf driver to t4vf_bar2_sge_qregs to
avoid conflicts. Also fixes alignment for these function.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs entry to inject Freelist starvation, used only for debugging
purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Cavium ThunderX network controller.
The driver is on the pci bus and thus requires the Thunder PCIe host
controller driver to be enabled.
Signed-off-by: Maciej Czekaj <mjc@semihalf.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Kamil Rytarowski <kamil@semihalf.com>
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sruthi Vangala <svangala@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xennet_remove() freed the queues before freeing the netdevice which
results in a use-after-free when free_netdev() tries to delete the
napi instances that have already been freed.
Fix this by fully destroy the queues (which includes deleting the napi
instances) before freeing the netdevice.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As many issues are encountered at probe time, where MCDI logging can't be
enabled through the sysfs node, this change adds a module parameter
'mcdi_logging_default', which defaults to false. When set to true, newly-
probed functions will have MCDI logging enabled. The setting can
subsequently be changed as normal through the sysfs node.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCDI tracing is enabled per-function with a sysfs file
/sys/class/net/<NET_DEV>/device/mcdi_logging
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCDI tracing is conditional on CONFIG_SFC_MCDI_LOGGING, which is enabled
by default.
Each MCDI command will produce a console line like
sfc dom🚌dev:fn ifname: MCDI RPC REQ: xxxxxxxx [yyyyyyyy...]
where xxxxxxxx etc. are the raw MCDI payload in 32-bit hex chunks.
The response will then produce a similar line with "RESP" instead of "REQ",
and containing the MCDI response payload (if any).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're seeing some softlockups from this function when there
are a lot fdb entries on a vxlan device. Taking the lock for
each bucket instead of the whole table is enough to fix that.
Signed-off-by: Sorin Dumitru <sdumitru@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the at86rf230 version check which is used
by the rzusb stick.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The test in mlx4_load_one() to remove MLX4_FLAG_MSI_X expects mlx4_NOP() to
fail with -EBUSY. It is also necessary to avoid the reset since the device
is not fully reinitialized before calling mlx4_start_hca() a second time.
Note that this will also affect mlx4_test_interrupts(), the only other user
of MLX4_CMD_NOP.
Fixes: f5aef5a ("net/mlx4_core: Activate reset flow upon fatal command cases")
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e9ce7cb6b1 ("xen-netback: Factor queue-specific data into queue
struct") introduced a regression when moving queue-specific data into
the queue struct by failing to set the credit_bytes field. This
prevented bandwidth limiting from working. Initialize the field as it
was done before multiqueue support was added.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update all open-coded tests for all 4 PHY_INTERFACE_MODE_RGMII* values
to use the newly introduced helper: phy_interface_is_rgmii.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If read() syscall requests unexpected number of bytes from "dimm" binary
attribute file, return EINVAL instead of EPERM.
At the same time pin down sysfs file size to the fixed
sizeof(struct netxen_dimm_cfg), which allows to exploit some missing
sanity checks from kernfs (file boundary checks vs offset etc.)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.
Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.
This patch fixes a bug introduced by:
d9663c8c21 ("amd-xgbe-phy: Use phydev advertising field vs supported")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b112889c5a ("iwlwifi: mvm: add Aux ROC request/response flow")
added aux ROC flow in addition to the existing ROC flow. While doing
it, it moved the ROC reference release to a common work item, which
is being called for both the ROC and aux ROC flows.
This resulted in invalid reference accounting, as no reference was
taken in case of aux ROC, while a reference was released on completion.
Fix it by adding a reference for the aux ROC as well, and release
only the relevant references on completion (according to the set bits).
While at it, convert cancel_work_sync() to flush_work(), in order
to make sure the references are being cleaned properly.
Fixes: b112889c5a ("iwlwifi: mvm: add Aux ROC request/response flow")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We should not call the iwl_pcie_set_pwr() functions in the
suspend/resume flows for family 8000, because the register used is
locked in devices from this family. Doing this causes an NMI
protection error (RT_NMI_INTERRUPT_PREG_PROTECTION).
To fix this, skip those calls if the device family is
IWL_DEVICE_FAMILY_8000.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we disconnect from the AP, drivers call cfg80211_disconnect().
This doesn't know whether the disconnection was initiated locally
or by the AP though, which can cause problems with the supplicant,
for example with WPS. This issue obviously doesn't show up with any
mac80211 based driver since mac80211 doesn't call this function.
Fix this by requiring drivers to indicate whether the disconnect is
locally generated or not. I've tried to update the drivers, but may
not have gotten the values correct, and some drivers may currently
not be able to report correct values. In case of doubt I left it at
false, which is the current behaviour.
For libertas, make adjustments as indicated by Dan Williams.
Reported-by: Matthieu Mauger <matthieux.mauger@intel.com>
Tested-by: Matthieu Mauger <matthieux.mauger@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
PCIe full dongle firmware can support a dma indices feature with which
firmware can update/fetch the read/write indices of message buffer
rings on both host to dongle and dongle to host directions. The support is
announced by firmware through shared flags.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_dma_flush and brcmf_dma_invalidate_cache are not necessary and
have never been implemented.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All pcie full dongle chips supported by fmac are using rev 5+ shared
structure. This patch removes the rev4 related code.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx flow worker in msgbuf gets scheduled at tx till a certain
threshold has been reached. Then the tx completes will take over
the scheduling. When amsdu and ampdu is used the frames are
transferred wireless in a very bulky fashion, in combination
with this scheduling algorithm and buffer limiters in the stack
this can result in limited throughput. This change causes the
flow worker to be scheduled more frequently from tx.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As described in the device tree bindings for 'brcm,bcm4329-fmac'
nodes, the interrupts property is optional. So adding a check
for the presence of this property before attempting to parse
and map the interrupt. If not present or parsing fails return
and fallback to in-band sdio interrupt.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This would ensure dmesg logs are not spammed with "unknown mgmt frame
subtype" messages.
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes typos in drivers/net/wirless/rtlwifi/Kconfig.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[ar5008 and ar9002]_hw_spur_mitigate have big portion of identical code.
This patch will move common part of ar5008_hw_spur_mitigate to
ar5008_hw_cmn_spur_mitigate and reuse it in ar9002_hw_spur_mitigate.
As noticed by Joe Perches I reuse ar9002_hw_spur_mitigate (const) version of
declarations for pilot_mask_reg and chan_mask_reg.
There should be no other difference with original code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several of these drivers have there TX randomly blocked for 3~5 seconds while
measuring tx throughput (iperf). The root couse happens in rtl_pci_flush().
The function uses a while-loop to wait for TX queue length to decrease to 0.
The TX queue length counts the number of packets that are queued in the driver.
The driver relys on the TX OK interrupt to return skb and reduce TX queue length.
The interrupt subroutine disables interupts, reads the interrupt registers, and
then clears the registers in the beginning of _rtl_pci_interrupt(). After all
interupts process are finished, the driver invokes enable_interrupt() to enable
interupts. This behavior is normal for an interrupt subroutine.
But enable_interrupt() invokes clear_interrupt() again. This unexpected interrupt
clearing may cleari me fresh TX OK interrupts. These missing interrupts cause TX
queue length to never reduce to 0i, which causes rtl_pci_flush() to be stuck in
unterminated while-loop.
This patch removes clear_interrupt() in enable_interrupt() to avoid this behavior.
Signed-off-by: Vincent Fann <vincent_fann@realtek.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver was not setting a channel plan. Now it gets it from EEPROM.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver is converted to use the channel plan in the EEPROM.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver was setting a channel plan for the world. Now it reads it fromi
EEPROM.
In addition, a typo was fixed.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver was setting a channel plan for the world. Now it reads it from
EEPROM.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver rtlwifi maintains its own regulatory information, The Chrome Autotest
(https://www.chromium.org/chromium-os/testing/autotest-user-doc)
showed some errors. This patch adds the necessary information for rtlwifi.
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are used like:
set_bit(WORK_LINK_UP, &priv->work_pending);
The problem is that set_bit() takes the actual bit number and not a mask
so static checkers get upset. It doesn't affect run time because we do
it consistently, but we may as well clean it up.
Fixes: 6010ce07a6 ('rndis_wlan: do link-down state change in worker thread')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In d8a2c51cdc ('ath9k_htc: Use atomic operations for op_flags') we
changed things like this:
- if (priv->op_flags & OP_TSF_RESET) {
+ if (test_bit(OP_TSF_RESET, &priv->op_flags)) {
The problem is that test_bit() takes a bit number and not a mask. It
means that when we do:
set_bit(OP_TSF_RESET, &priv->op_flags);
Then it sets the (1 << 6) bit instead of the 6 bit so we are setting a
bit which is past the end of the unsigned long.
Fixes: d8a2c51cdc ('ath9k_htc: Use atomic operations for op_flags')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-5.0 gained a new warning in the fwsignal portion of the brcmfmac
driver:
drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c: In function 'brcmf_fws_txs_process':
drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c:1478:8: warning: 'skb' may be used uninitialized in this function [-Wmaybe-uninitialized]
This is a false positive, and marking the brcmf_fws_hanger_poppkt function
as 'static inline' makes the warning go away. I have checked the object
file output and while a little code gets moved around, the size of
the binary remains identical.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added, and the assignments
as well as error checking fixed up.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/carl9170/usb.c:675
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_CARL9170=m
Patch is against 4.1-rc3 (localversion-next is -next-20150512)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch changes all debug print functions from dev_dbg/dev_err/dev_info
to mwifiex specific debug functions.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch is to add support for data hexdump debug feature.
It is controlled by level debug_mask in adapter structure.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for debugging print control in mwifiex driver.
The debug level can be controlled via either by modules load parameter
debug_mask or by writing to debug_mask in debugfs file.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for FW memory read/write operations via debugfs.
This is useful during debugging FW issues.
Examples:
For reading FW memory location:
echo r 0x01ac > /sys/kernel/debug/mwifiex/mlan0/memrw
cat /sys/kernel/debug/mwifiex/mlan0/memrw
For writing FW memory location:
echo w 0x01ac 0x55aa > /sys/kernel/debug/mwifiex/mlan0/memrw
Signed-off-by: Chin-ran Lo <crlo@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During usage of the new Bluetooth driver for Realtek devices, it was found
that BT scans were inhibited for the RTL8723BE when wireless was active. The
exact cause of this interference is not known yet, but a satisfactory work
around has been found that does not seem to have any visible side effects.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Shao Fu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The PCI cache line size value was being compared against decimal values
prefixed with 0x.
Fixed the literals to use the correct hex values.
This has not been tested due to lack of hardware. However, the value in
`cline` is PCI cache line size, which is the CPU's cache line size.
It is less likely for cache line sizes to be 22 or 50, and more likely for
them to be 16 or 32. Also, as far as I understand, cache line size is used for
things like aligning DMA requests with CPU cache line, which improve
performance but wouldn't break anything if the value doesn't match. In
this case, we will fall through to the default case which leaves `reg`
unchanged.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes these checkpatch.pl errors around a single switch-case
block:
ERROR: switch and case should be at the same indent
ERROR: trailing statements should be on next line
More specifically, the fix has been applied to the five occurances of
the errors listed below.
ERROR: switch and case should be at the same indent
#1100: FILE: adm8211.c:1100:
+ switch (cline) {
[...]
+ default: reg |= (0x0 << 14);
ERROR: trailing statements should be on next line
#1101: FILE: adm8211.c:1101:
+ case 0x8: reg |= (0x1 << 14);
ERROR: trailing statements should be on next line
#1103: FILE: adm8211.c:1103:
+ case 0x16: reg |= (0x2 << 14);
ERROR: trailing statements should be on next line
#1105: FILE: adm8211.c:1105:
+ case 0x32: reg |= (0x3 << 14);
ERROR: trailing statements should be on next line
#1107: FILE: adm8211.c:1107:
+ default: reg |= (0x0 << 14);
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ACPI will manage WiFi chip's power state during suspend/resume
process on some tablet platforms(such as ASUS T100TA). This is
not supported by brcmfmac driver now, and the context of WiFi
chip will be damaged after resume. This patch informs ACPI not
to manage WiFi chip's power state.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
parameter "infra_mode" of rtl92c_init_beacon_max_error() is not used.
so i remove this.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialization routine set REG_BCN_MAX_ERR to 0xFF.
also _rtl92cu_set_media_status set REG_BCN_MAX_ERR to same value.
so i remove this code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A pair of nested spin locks was introduced in commit 63502b8d0
"dp83640: Fix receive timestamp race condition".
Unfortunately the 'flags' parameter was reused for the inner lock,
clobbering the originally saved IRQ state. This patch fixes the issue
by changing the inner lock to plain spin_lock without irqsave.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of the ext_write function are supposed to hold a mutex that
protects the state of the dialed page, but one caller was missing the
lock from the very start, and over time the code has been changed
without following the rule. This patch cleans up the call sites in
violation of the rule.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the calibration function that corrects the initial offsets
among multiple devices only works the first time. If the function is
called more than once, the calibration fails and bogus offsets will be
programmed into the devices.
In a well hidden spot, the device documentation tells that trigger indexes
0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work.
This patch fixes the issue by using one of the special triggers during the
recalibration method.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function, cpsw_intr_disable, already calls cpdma_ctlr_int_ctrl. There
is no need to disable the dma interrupts twice. This patch removes the
extra calls.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function, cpsw_intr_enable, already calls cpdma_ctlr_int_ctrl. There
is no need to enable the dma interrupts twice. This patch removes the
extra call.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The funtions, cpsw_ale_flush and cpsw_ale_set_ageout, have never been used
since they were first introduced. This patch removes the dead code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the breaks too far to the left makes parsing the dense switch/case
block unnecessarily harder.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark parameters and local variables as const where possible.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused rocker_port parameter from rocker_port_kfree.
Also remove the rocker_port parameter from callers of rocker_port_kfree
where the parameter it is now unused.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two uses seem to have had carriage returns removed.
Make these entries like all the others in this file.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
is not a clean solution as it does not handle all corner cases correctly.
By changing the conversion to use msecs_to_jiffies(val) conversion is
correct in all cases.
in the current code:
mod_timer(&self->rx_defer_timer, jiffies + (10 * HZ / 1000));
for HZ < 100 (e.g. CONFIG_HZ == 64|32 in alpha) this effectively results
in no delay at all.
Patch was compile tested for x86_64_defconfig (implies CONFIG_USB_IRDA=m)
Patch is against 4.1-rc4 (localversion-next is -next-20150522)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac DebugFS entries are currently global to the driver. As a result,
having more than one stmmac device in the system creates the following
error:
* ERROR stmmaceth, debugfs create directory failed
* stmmac_hw_setup: failed debugFS registration
This also results in being able to access the debugfs information for
the first registered device only.
This patch changes the debugfs structure to have one sub-directory per
net-device. Files under "/sys/kernel/debug/stmmaceth" will now show-up
under /sys/kernel/debug/stmmaceth/ethN/.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix in send of emac regs dump to ethtool which
causing in wrong data interpretation on ethtool
layer for MII and EMAC.
Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable separate_tx_rx_irq is bool type so assigning true
instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix firmware name and other things to enable 3165
* fix bad APMG configuration for 8000 (no AMPG on these devices)
* fix MAC address assignment for 8000
* fix firmware debugging triggers (MLME)
* fix several bugs in low power states code (net-detect, d0i3)
ssb:
* fix reboot after device reset for WRT350N v1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVYwxHAAoJEG4XJFUm622bBTwH/RH0Yx5MBK+sD4d16i70d5nh
dbE0wSBy9ZOT6cMVkAqViZg9T+EQ61+Lre7hwNNM6l/NLkTyjyEXB0Not9ERfLc/
E1g4BBHUfg9LUrbufIgWcTZRLewMk7lOBDN22hIcaVYAM6m9QFNwK+qnkFSXNkCq
Pc0aRDWEYHrVvx8A/XYjInrb/oJqT6z7t83lWHbgtJGmCAVsEaqSvdn2badpecHi
xar7PrdvYkXzFyd7xxmXPcvwkiAzKdIDdF3WR+SuS/V7Tk+2Cw5yrBWrIKc3QqtA
+DfIY3Xa9zHHr1SLvoOQ0VooWTsY+RhSdmEbilG0KFOgNnJz3Zm5Abr2mzkvqvA=
=05aZ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* fix firmware name and other things to enable 3165
* fix bad APMG configuration for 8000 (no AMPG on these devices)
* fix MAC address assignment for 8000
* fix firmware debugging triggers (MLME)
* fix several bugs in low power states code (net-detect, d0i3)
ssb:
* fix reboot after device reset for WRT350N v1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for flashing 10GBaseT adapter with BCM 84834 PHY and
Aquantia AQ1202 PHY.
Updating of the PHY firmware must happen before the INITIALIZE_CMD.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding support for 7425 PHY in the 7xxx PHY driver, the ID that
was used was actually coming from an external PHY: a BCM5461x. Fix this
by using the proper ID for the internal 7425 PHY and set the
PHY_IS_INTERNAL flag, otherwise consumers of this PHY driver would not
be able to properly identify it as such.
Fixes: d068b02cfd ("net: phy: add BCM7425 and BCM7429 PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change more netdev_dbg statements over to netif_dbg and add some new
netif_dbg statements to the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.
Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device private data structure contains all the defined hardware
features for the device. However one of the features is not set. Even
though the feature is not currently used, set it to avoid future
issues of the feature being checked thinking it has been properly set.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVXbP3AAoJEG4XJFUm622b5KoH/1qlTHsKcyvdxlhQOgYNGCXA
HNMwcxtwFyRYHFeVTGOQp2BVknEoqWTwGv1m4FQ1pBSSwuUvAyw4BHNSRat/zaNc
wLnZgUYKH5VHeoE/cpe/Asowau+u8hru1adPsVSjudTXMinKrNaDUfjSs2U+UR0+
BaC3PtsANk7wH82+bZq3qXYjcaZITObDe3WBmMNMG0nTimS6pScgnTUnfHch+CEA
0sTOlZF+QTGiH/c5tw2SAoRft4OG+oTnWYQ+vEEQsVev7Yegasa/kg4NdDVdjBNk
9VH9aDlQfGgxodCoeJuQCDzUZL8ixnvYTLeUTxqypzx9Cw0TsLDwoMQA+Ux3G8w=
=JSya
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
ath10k:
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the limitation that disallows configuring single ported VFs
in the presence of IB ports, after addressing the issues that
prevented that to work.
SMI (QP0) requests/responses are still not supported for single
ported IB VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's legal for drivers to provide the QP port through the
QPC schedule-queue field on the reset-to-init QP state change.
Add adjusting of the schedule queue port in the SRIOV wrapper
for that operation too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some VF drivers flow set the schedule queue in the QP context but
without setting none of OPTPAR_SCHED_QUEUE or OPTPAR_PRIMARY_ADDR_PATH.
To allow for such non-modified drivers to function as single ported
IB VFs, we must adjust the schedule queue port whenever being set,
e.g as currently done for single ported Eth VFs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of enabling single ported VFs over IB ports we need to handle
some of the flows for generting EQ events for VFs which don't come
into play under Eth ports.
This mainly includes port management events derived from changes of the
phyiscal port (lid change, client re-register, down/up, etc), VF pkey table
changes and VF guid changes initiated by the IB driver.
(1) make sure that events are generated only for VFs sitting on
the relevant physical port (under the ALL_SLAVES flow).
(2) before generating the event, convert from physical (one or two)
to VF port (always equals one).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Single port VFs always provide port = 1 (even if the actual physical
port used is port 2). As such, we need to convert the port provided
by the VF to the physical port before calling into the firmware.
It turns out that the Linux mlx4 VF RoCE driver maintains a copy of
the GID table and hence this change became critical only for single
ported IB VFs, but it could be needed for other RoCE VF drivers too.
Fixes: 449fc48866 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e21 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware revisions pad 4th hw address in
Native Wifi Rx decap. This is the case with 10.x
and it was assumed that this is true for all
firmware images.
However QCA988X with 999.999.0.636 and QCA61X4
with WLAN.RM.2.0-00088 don't have the padding.
Hence add a feature flag indicating that the
padding isn't present so firmware images can
advertise it appropriately. This way driver will
behave as it was before with old firmware blobs
and doesn't cause any regressions from user
perspective.
Effectively this patch enables QCA988X with
999.999.0.636 and QCA61X4 with WLAN.RM.2.0-00088
to set up client bridging provided user has an
updated firmware blob.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By using SOC_WAKE register it is possible to bring
down power consumption of QCA61X4 from 36mA to
16mA when associated and idle.
Currently the sleep threshold/grace period is at a
very conservative value of 60ms.
Contrary to QCA61X4 the QCA988X firmware doesn't
have Rx/beacon filtering available for client mode
and SWBA events are used for beaconing in AP/IBSS
so the SoC needs to be woken up at least every
~100ms in most cases. This means that QCA988X
is at a disadvantage and the power consumption
won't drop as much as for QCA61X4.
Due to putting irq-safe spinlocks on every MMIO
read/write it is expected this can cause a little
performance regression on some systems. I haven't
done any thorough measurements but some of my
tests don't show any extreme degradation.
The patch removes some explicit pci_wake calls
that were added in 320e14b8db51aa ("ath10k: fix
some pci wake/sleep issues"). This is safe because
all MMIO accesses are now wrapped and the device
is woken up automatically if necessary.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 can update vif powersave state while
disconnected. Firmware doesn't behave nicely and
consumes more power than necessary if PS is
disabled on a non-started vdev. Hence
force-enable PS for non-running vdevs.
This reduces power drain on QCA61X4 from 88mA to
36mA when interface is up and not associated.
QCA988X wasn't measured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is actually safe to enable ASPM after the
device is booted up.
This reduces power drain of QCA61X4 when driver is
simply loaded (no interface is up) from 31mA to
14mA. QCA988X wasn't measured but doesn't seem to
regress in any other way.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix format specifier used for dma_addr_t, namely use %pad
Debug print virtual address for the same buffer as well.
Fixes: dc16427bbe ("wil6210: Add pmc debug mechanism memory management")
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* fix bad APMG configuration for 8000 (no AMPG on these devices)
* fix MAC address assignment for 8000
* fix firmware debugging triggers (MLME)
* fix several bugs in low power states code (net-detect,
d0i3)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bz0b
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2015-05-21' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* fix firmware name and other things to enable 3165
* fix bad APMG configuration for 8000 (no AMPG on these devices)
* fix MAC address assignment for 8000
* fix firmware debugging triggers (MLME)
* fix several bugs in low power states code (net-detect,
d0i3)
Since the caller already check the presence of a of_node there
is no need to repeat the check in stmmac_probe_config_dt.
There is also no point in checking the return value of the
of_match_device function since if there wasn't match in the
first place we would never be in this function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since stmmac_dvr_probe takes care of setting driver data and
assign resources to the priv structure there is no need to
access the priv structure from the other probe functions.
This mean that this function can be changed into just return
an int and thus simplifying the callers.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creat a struct that contain all the resources that needs to be
assigned to the priv struct in stmmac_dvr_probe. This makes it
possible to factor out more common code from the other probe
functions and also use this struct to hold the resources as
they are fetched.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting of driver data into stmmac_dvr_probe so the
other probe functions don't have to. This will help to
simplify the other probe functions later.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some T4/T5 registers that were included incorrectly.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a set_mac_address() NIC-type function for EF10 only, and
use this to set the MAC address on the vadaptor. For Siena and
earlier, the MAC address continues to be set by MC_CMD_SET_MAC;
this is still called on EF10, and including a MAC address in
this command has no effect.
The sriov_mac_address_changed() NIC-type function is no longer
needed on EF10, but it is needed for Siena where it is used to
update the peer address of the PF for VFDI. Change this to use
the new set_mac_address function pointer.
efx_ef10_sriov_mac_address_changed() is no longer called, as VFs
will try to change the MAC address on their vadaptor rather than
trying to change to the context of the PF to alter the vport.
When a VF is running in direct passthrough mode with MAC spoofing
enabled, it will be able to change the MAC address on its vadaptor.
In this case, there is a link to the PF, so find the correct VF in
its ef10_vf array and update the MAC address.
ndo_set_mac_address() can be called during driver unload while
bonding, and in this case the device has already been stopped, so
don't call efx_net_open() to restart it after reconfiguration.
efx->port_enabled is set to false in efx_stop_port(), so it is
indicator of whether the device needs to be restarted.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exercised with
"ip link set <PF intf> vf <vf_i> state {auto|enable|disable}"
Sets the reporting policy for VF link state to either
- mirror physical link state
- always up
- always down
get VF link state mode in efx_ef10_sriov_get_vf_config
Exercised by
"ip link show <PF intf>";
output will include a line like
vf 0 MAC 12:34:56:78:9a:bc, link-state auto
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max vlan tags that can be offloaded is 2, including any upstream VLAN
aggregator. Currently there is no way for the net driver to know whether
the upstream vswitch (if any) is using vlan tags, so there is no way to
know how many tags we can request.
Along with the implementation for the ndo_set_vf_vlan callback, this patch
also adds 2 VLAN tags for the driver created VEB switch if possible, that
way it is possible to offload as many tags as are allowed.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we do an entity reset when we detect an MC reboot.
This messes up SRIOV because it leaves VFs orphaned. The extra
reset is rather redundant anyway, since the MC reboot will have
basically reset everything.
This change replaces the entity reset after MC reboot with a
simpler datapath reset that reallocates resources but doesn't
perform the entity reset.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnetlink calls ndo_get_vf_config when compiling information
about a network interface, so that the VFs associated with a PF
can be listed (eg: ip link show).
Implement a response to this entry point and return PF-set MAC
address for VF in ndo_get_vf_config
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a response to this entrypoint.
The ndo_set_vf_mac() entrypoint is only exposed in the driver if
CONFIG_SFC_SRIOV is defined.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid MC bugs the flags field needs to be set to 0.
Instead of explicitly clearing out the flags individually, a
better way to do this is to memset the MCDI_BUF to 0.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A VF's MAC address is set by its parent PF and added to its vport.
To get this MAC address, the VF must use MC_CMD_ VPORT_GET_MAC_ADDRESSES.
In the current scheme, a VF's vport should only have one MAC address,
so warn if this is not the case.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If MCDI timeouts are encountered during efx_ef10_filter_table_remove(),
an FLR will be queued, but efx->filter_state will still be kfree()d.
The queued FLR will then call efx_ef10_filter_table_restore(), which
will try to use efx->filter_state. This previously caused a panic.
This patch adds an rwsem to protect the existence of efx->filter_state,
separately from the spinlock protecting its contents. Users which can
race against efx_ef10_filter_table_remove() should down_read this rwsem.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialised in efx_probe_vf and removal is dealt with in
efx_ef10_remove.
vf->efx is needed in future patches to change the MAC address
of the VF via the parent PF, while the driver is bound to the
VF.
Example: ip link set dev vf NUM mac LLADDR
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the PF and VF can disagree on the VF's MAC address and
this leads to strange behaviour, up to and including kernel panics.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added function efx_ef10_get_vf_index to store the vf_index
in nic_data during probe
vf_index is needed in future patches to access a particular
VF in the VF data structure.
Moved efx_ef10_probe_pf and efx_ef10_probe_vf in order to
used efx_ef10_remove
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC_CMD_SET_MAC is privileged and can only by called by the link
control function.
This patch adds efx_ef10_mac_reconfigure_vf which avoids the call
to MC_CMD_SET_MAC by the Virtual function
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is one primary function per adaptor, one link control function
per port and the rest as categorised as general.
This patch adds privileges to the MCDI commands based on which
functions are allowed to call them.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also matches with the sibling call netdev_alloc_skb_ip_align() made in
rx fast path.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
30 usecs (or really, 1 jiffy) can go by pretty fast.
Move the set of the timeout immediately before the loop.
Remove the unnecessary max(1ul, usecs_to_jiffies(30)) as
usecs_to_jiffies with a non-zero constant is guaranteed
to be non-zero.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The motivation for this is that rocker_port_internal_vlan_id_{get,put} appear
to only partially implement the transaction model: memory allocation
and freeing is transactional, but hash and bitmap manipulation is not.
The latter could be fixed, however, as it is not currently exercised
due to trans always being SWITCHDEV_TRANS_NONE it seems cleaner
to make rocker_port_internal_vlan_id_get non-transactional.
This problem was introduced by c4f20321d9 ("rocker: support
prepare-commit transaction model").
Found by inspection.
I do not believe that this change should have any run-time effect.
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rocker_port_ipv4_nh() and in turn rocker_port_ipv4_neigh() may be
be called with trans == SWITCHDEV_TRANS_PREPARE and then
trans == SWITCHDEV_TRANS_COMMIT from switchdev_port_obj_set() via
fib_table_insert().
The first time that rocker_port_ipv4_nh() is called, with
trans == SWITCHDEV_TRANS_PREPARE, _rocker_neigh_add() adds a new entry to
the neigh table.
And the second time rocker_port_ipv4_nh() is called, with
trans == SWITCHDEV_TRANS_COMMIT, that entry is found. This causes
rocker_port_ipv4_nh() to believe it is not adding an entry and thus it
frees "entry", which is still present in rocker driver's neigh table.
This problem does not appear to affect deletion as my analysis is that
deletion is always performed with trans == SWITCHDEV_TRANS_NONE.
For completeness _rocker_neigh_{add,del,prepare} are updated not to
manipulate fib table entries if trans == SWITCHDEV_TRANS_PREPARE.
Fixes: c4f20321d9 ("rocker: support prepare-commit transaction model")
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic mechanism to declare a bitmap instead of unsigned long.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qos_seq points (to a struct) inside the command response data.
Make sure to free the response only after qos_seq is not
needed anymore.
Reported-by: Heng Luo <heng.luo@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are buses that can't handle ASYNC command without
copying them. Duplicate the host command instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take the MAC address from the OTP even if one is present in
the NVM, if that MAC address happens to be a reserved one.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
fw_status is the only pointer pointing to a block of memory
allocated above and should be freed after use.
Note: this come from Klockwork static analyzer.
Cc: stable@vger.kernel.org [3.19+]
Fixes: 2021a89d7b ("iwlwifi: mvm: treat netdetect wake up separately")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since firmware version 0.2 we use AACK handling directly in the firmware.
Inform the stack that the hardware supports and uses it.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Together with mainlining the driver we released a first public binary version
of the device firmware. This is version 0.2. With this change we warn users
who run outdated versions of the firmware. While we have not seen problems
with it yet (thus no error, but a warning only) it would be better to run the
released and tested firmware. You can find released versions here:
http://downloads.qi-hardware.com/people/werner/wpan/web/
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is an alternative way of fixing:
commit db9683fb41 ("net: phy: Make sure PHY_RESUMING state change
is always processed")
When the PHY state transitions from PHY_HALTED to PHY_RESUMING, there are
two things we need to do:
1). Re-enable interrupts (and power up the physical link, if powered down)
2). Update the PHY state and net-device based on the link status.
There's no strict reason why #1 has to be done from within the main
phy_state_machine() function. There is a risk that other changes to the
PHY (e.g. setting speed/duplex, which calls phy_start_aneg()) could cause
a subsequent state transition before phy_state_machine() has processed
the PHY_RESUMING state change. This would leave the PHY with interrupts
disabled and/or still in the BMCR_PDOWN/low-power mode.
Moving enabling the interrupts and phy_resume() into phy_start() will
guarantee this work always gets done. As the PHY is already in the HALTED
state and interrupts are disabled, it shouldn't conflict with any work
being done in phy_state_machine(). The downside of this change is that if
the PHY_RESUMING state is ever entered from anywhere else, it'll also have
to repeat this work.
Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
