Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from board
files to DT. Tony thinks this was the last major set of fixes, with
maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed PCIe
hardware, i.e. incorrect number of busses on some SoCs, etc. The line
delta adds up due to various ranges moving around when this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in my
test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91, a couple
of reverts for ux500, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PljB
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from
board files to DT. Tony thinks this was the last major set of
fixes, with maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed
PCIe hardware, i.e. incorrect number of busses on some SoCs, etc.
The line delta adds up due to various ranges moving around when
this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in
my test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91,
a couple of reverts for ux500, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk
arm: socfpga: Enable ARM_TWD for socfpga
ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
ARM: multi_v7_defconfig: enable network for BeagleBone Black
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
...
Pull timer fixes from Thomas Gleixner:
- timekeeping: Cure a subtle drift issue on GENERIC_TIME_VSYSCALL_OLD
- nohz: Make CONFIG_NO_HZ=n and nohz=off command line option behave the
same way. Fixes a long standing load accounting wreckage.
- clocksource/ARM: Kconfig update to avoid ARM=n wreckage
- clocksource/ARM: Fixlets for the AT91 and SH clocksource/clockevents
- Trivial documentation update and kzalloc conversion from akpms pile
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Fix another inconsistency between CONFIG_NO_HZ=n and nohz=off
time: Fix 1ns/tick drift w/ GENERIC_TIME_VSYSCALL_OLD
clocksource: arm_arch_timer: Hide eventstream Kconfig on non-ARM
clocksource: sh_tmu: Add clk_prepare/unprepare support
clocksource: sh_tmu: Release clock when sh_tmu_register() fails
clocksource: sh_mtu2: Add clk_prepare/unprepare support
clocksource: sh_mtu2: Release clock when sh_mtu2_register() fails
ARM: at91: rm9200: switch back to clockevents_config_and_register
tick: Document tick_do_timer_cpu
timer: Convert kmalloc_node(...GFP_ZERO...) to kzalloc_node(...)
NOHZ: Check for nohz active instead of nohz enabled
Some of the clocks that were designated gate-clk do not have a gate, so
change those clocks to be of periph-clk type.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable MMC/SD on the Broadcom mobile platforms, and increase the block
minors from the default 8 to 16 (since the Broadcom board by default
has root on the 8th partition).
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org # v3.12
This enables a few more options on the sunxi defconfigs such that I can
use nfsroot to boot them (there is no local storage support yet). It
also enables PRINTK_TIME and tmpfs since it's a common distro requirement.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few more legacy booting vs device tree booting fixes that people
have noticed while booting things with device tree for things like
omap4 WLAN, smsc911x, and beagle audio. Hopefully this will be it
for the legacy booting vs device tree fixes for this -rc cycle.
* tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
BeagleBone Black uses the TI CPSW ethernet controller, enable it in the
multi_v7_defconfig for testing coverage purposes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v3.12
From Nicolas Ferre:
AT91: second round of fixes for 3.13
- reduce IP frequency for I2C on sama5d3
- missing aliases directive for USART3 on 9x5 family
- a PM symbol is missing if !CONFIG_PM
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
From Jason Cooper, mvebu DT fixes for v3.13:
- mvebu
- PCIe fixes now that we have test devices with more ports.
- fix access to coherency registers
* tag 'mvebu-dt-fixes-3.13' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: re-enable PCIe on Armada 370 DB
ARM: mvebu: use the virtual CPU registers to access coherency registers
ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260
ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
drivers/net/ethernet/smsc/smsc911x.c is expecting supplies named
"vdd33a" and "vddvario". Currently the shared DTS file provides
"vmmc" and "vmmc_aux", and the supply lookup will fail:
smsc911x 2c000000.ethernet: Looking up vdd33a-supply from device tree
smsc911x 2c000000.ethernet: Looking up vdd33a-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
smsc911x 2c000000.ethernet: Looking up vddvario-supply from device tree
smsc911x 2c000000.ethernet: Looking up vddvario-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
Fix it!
Looks like commmit 6b2978ac40 (ARM: dts: Shared file for omap GPMC
connected smsc911x) made the problem more visible by moving the smc911x
configuration from the omap3-igep0020.dts file to the generic file.
But it seems we've had this problem since commit d72b441501
(ARM: dts: omap3-igep0020: Add SMSC911x LAN chip support).
Tested on OMAP3 Overo platform.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[tony@atomide.com: updated comments for the commits causing the problem]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 'cd8abed' "ARM: OMAP2+: Powerdomain: Remove the need to
always have a voltdm associated to a pwrdm" leads to the following
Smatch complaint:
arch/arm/mach-omap2/powerdomain.c:131 _pwrdm_register()
error: we previously assumed 'arch_pwrdm' could be null (see line 105)
So, fix the unchecked dereference of arch_pwrdm.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds typical McBSP2-TWL4030 audio description to the legacy
Beagle Board.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux mode for wlan/sdmmc5 should be MODE0 in pinmux_wl12xx_pins and
Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes WLAN on omap4-sdp that got broken in v3.10 when we
moved omap4 to boot using device tree only as I did not have
the WL12XX card in my omap4 SDP to test with. The commit that
attempted to make WL12XX working on omap4 SDP was 775d2418f3
(ARM: dts: Fix muxing and regulator for wl12xx on the SDIO
bus for blaze).
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: updated comments for the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.
Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x
SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:
https://bugzilla.kernel.org/show_bug.cgi?id=63821
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSnJuAAAoJEFjIrFwIi8fJj7sIAJQgSEMWJcEOBJ3lujfbhhKr
9GYfyNILfBjaOcH3LkA354U0JB3y4vON/xz6ONzMO4X7Jj6oUzACeEluq2iexlji
VDxqtnDJGS/82TcIN5xOVKRZbIqZ0xdRjK2f4h7AU9lIoIk+SJEJIycG1RGqqrmr
0nv39lUMjQhXNDhUjyt7e6JQj5GHrP0hzp5ngEQGcquPKbHXUInlwkB/kCH3zwju
2kEYQyKSWFoZCVtIBDeHplcZw9r/zWyOHBxjWOVoI/KZk8k+6d2breC3hv0lrhvU
qkJwzJcKZGlFdiCVHLbo3sTHf0NvvfF+qBCv7JbsymYaQc5SkrATmQ/DAUOssg0=
=emSu
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"Fixes to patches that went in this merge window along with a latent
bug:
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM"
* tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gnttab: leave lazy MMU mode in the case of a m2p override failure
xen/arm: p2m_init and p2m_lock should be static
arm/xen: Export phys_to_mach to fix Xen module link errors
swiotlb-xen: add missing xen_dma_map_page call
If CONFIG_PM is not defined, then arch/arm/mach-at91/pm.c is not
compiled in. This patch creates an inline function that does nothing
if CONFIG_PM is not defined.
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alias was missing for SoC of the at91sam9x5 familly that embed USART3.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[b.brezillon@overkiz.com: advised to place changes in at91sam9x5_usart3.dtsi]
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
With some devices, transfer hangs during I2C frame transmission. This issue
disappears when reducing the internal frequency of the TWI IP. Even if it is
indicated that internal clock max frequency is 66MHz, it seems we have
oversampling on I2C signals making TWI believe that a transfer in progress
is done.
This fix has no impact on the I2C bus frequency.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull ARM fixes from Russell King:
"Some ARM fixes, the biggest of which is the fix for the signal return
codes; this came up due to an interaction between the V7M nommu
changes and the BE8 changes. Dave Martin spotted that the kexec
trampoline wasn't being correctly copied (in a way which allows
Thumb-2 to work).
I've also fixed a number of breakages on footbridge platforms as I've
upgraded one of my machines to v3.12... one which had a 1200 day
uptime"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7907/1: lib: delay-loop: Add align directive to fix BogoMIPS calculation
ARM: 7897/1: kexec: Use the right ISA for relocate_new_kernel
ARM: 7895/1: signal: fix armv7-m build issue in sigreturn_codes.S
ARM: footbridge: fix EBSA285 LEDs
ARM: footbridge: fix VGA initialisation
ARM: fix booting low-vectors machines
ARM: dma-mapping: check DMA mask against available memory
Copying a function with memcpy() and then trying to execute the
result isn't trivially portable to Thumb.
This patch modifies the kexec soft restart code to copy its
assembler trampoline relocate_new_kernel() using fncpy() instead,
so that relocate_new_kernel can be in the same ISA as the rest of
the kernel without problems.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Tested-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After "ARM: signal: sigreturn_codes should be endian neutral to
work in BE8" commit, thumb only platforms, like armv7m, fails to
compile sigreturn_codes.S. The reason is that for such arch
values '.arm' directive and arm opcodes are not allowed.
Fix conditionally enables arm opcodes only if no CONFIG_CPU_THUMBONLY
defined and it uses .org instructions to keep sigreturn_codes
layout.
Suggested-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- The LEDs register is write-only: it can't be read-modify-written.
- The LEDs are write-1-for-off not 0.
- The check for the platform was inverted.
Fixes: cf6856d693 ("ARM: mach-footbridge: retire custom LED code")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org
It's no good setting vga_base after the VGA console has been
initialised, because if we do that we get this:
Unable to handle kernel paging request at virtual address 000b8000
pgd = c0004000
[000b8000] *pgd=07ffc831, *pte=00000000, *ppte=00000000
0Internal error: Oops: 5017 [#1] ARM
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.12.0+ #49
task: c03e2974 ti: c03d8000 task.ti: c03d8000
PC is at vgacon_startup+0x258/0x39c
LR is at request_resource+0x10/0x1c
pc : [<c01725d0>] lr : [<c0022b50>] psr: 60000053
sp : c03d9f68 ip : 000b8000 fp : c03d9f8c
r10: 000055aa r9 : 4401a103 r8 : ffffaa55
r7 : c03e357c r6 : c051b460 r5 : 000000ff r4 : 000c0000
r3 : 000b8000 r2 : c03e0514 r1 : 00000000 r0 : c0304971
Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel
which is an access to the 0xb8000 without the PCI offset required to
make it work.
Fixes: cc22b4c185 ("ARM: set vga memory base at run-time")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: <stable@vger.kernel.org>
Commit f6f91b0d9f (ARM: allow kuser helpers to be removed from the
vector page) required two pages for the vectors code. Although the
code setting up the initial page tables was updated, the code which
allocates page tables for new processes wasn't, neither was the code
which tears down the mappings. Fix this.
Fixes: f6f91b0d9f ("ARM: allow kuser helpers to be removed from the vector page")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: <stable@vger.kernel.org>
Some buses have negative offsets, which causes the DMA mask checks to
falsely fail. Fix this by using the actual amount of memory fitted in
the system.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Beagle (rev. C4) and Beagle-XM (all revs) need VAUX2 1.8V supply
for the USB PHY.
As the generic PHY driver can't handle more than one supply
at the moment, we configure this supply to be always on.
This will cause a very small power impact if the USB host subsystem
is not in use, about 76.86 micro-W + LDO power.
Older Beagle boards (prior to C4) don't have VAUX2 connected anywhere,
so there won't be any functional impact on those boards other than
some additional LDO power consumption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Device Tree boot the VDDS_DSI regulator is not linked to
the DPI device so omapfb driver probing fails with:
[ 3.186035] OMAPFB: omapfb_probe
[ 3.190704] omapdss DPI error: can't get VDDS_DSI regulator
[ 3.196594] omapfb omapfb: failed to connect default display
[ 3.202667] omapfb omapfb: failed to init overlay connections
[ 3.208892] OMAPFB: free_resources
[ 3.212493] OMAPFB: free all fbmem
[ 3.216735] omapfb omapfb: failed to setup omapfb
As a workaround name the VPLL2 regulator from twl4030 as vdds_dsi
so getting the VDDS_DSI regulator will succeed on dpi_init_regulator().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node to support the USB Host and the USB OTG on the IGEP AQUILA
Processor Board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP AQUILA EXPANSION has a 32KBit EEPROM for user data storage.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the user leds on the IGEP AQUILA EXPANSION. The has two leds,
one green and one red, that are controllable by software.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the hdmi output and the LCD Controller on IGEP AQUILA. Also
configure the correct pinmux for output of video data from the SoC
to the HDMI encoder.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEPv2 has a TFP410 DPI-to-DVI encoder attached to OMAP's
Display SubSystem (DSS).
Add mux setup for DSS pins and also for the GPIO 170 pin that
is used to ensure that the DVI-D is powered down on power up.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pin muxing support for IGEP boards i2c controllers.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the boards are using the TI AM/DM37x processor, there is only a small
quantity of IGEP Processor Boards based on TI OMAP3530. So it's better use the
omap36xx.dtsi include instead of omap34xx.dtsi include. We can add support
for the 34xx based variant later on as needed.
To avoid confusion we have added to the model the (TI AM/DM37x) comment.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated comments for the 34xx to 36xx include change]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In
both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using
the same MMC interface and uses the same GPIOs.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both, IGEPv2 and IGEP COM MODULE have a bus-width of 4 not 8, so fix this and
do not mux data pins from mmc1_data4 to mmc1_data7.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP's DVI connector's DDC pins are connected to OMAP's third i2c bus.
When booting with Device Trees the requested bus number is set to -1
which means that the bus number should be dynamically assigned. So the
third i2c bus has 2 has a bus number.
Since now only DT booting is supported for IGEP boards after commit
06ff74fd ("ARM: OMAP2+: remove legacy support for IGEP boards"), the
i2c bus number has to be changed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling of Posted mode is seen to cause problems on dmtimer modules on AM33xx
(much like other OMAPs). Reference discussions on forums [1] [2]. Earlier
patch solving this on other OMAPs [3].
For OMAP SoCs with this errata, the fix has been to not enable Posted mode.
However, on some SoCs (atleast AM33xx) which carry this errata, Posted mode
is enabled on reset. So we not only need to ignore enabling of the POSTED bit
when the timer is requested, but also disable Posted mode if errata is present.
[1] http://e2e.ti.com/support/arm/sitara_arm/f/791/t/285744.aspx
[2] http://e2e.ti.com/support/arm/sitara_arm/f/791/t/270632.aspx
[3] http://www.spinics.net/lists/linux-omap/msg81770.html
Cc: stable@vgerk.kernel.org
Reported-by: Russ Dill <russ.dill@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Allow creation and mounting of devtmpfs, which is used
by OpenEmbedded root filesystems among others.
- Enable CPUidle for the ux500, it has been accidentally
disabled due to a Kconfig change.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=jJ0N
-----END PGP SIGNATURE-----
Merge tag 'ux500-defconfig-v3.13-rcs' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij, Ux500 defconfig patches for the v3.13 rc series:
- Allow creation and mounting of devtmpfs, which is used
by OpenEmbedded root filesystems among others.
- Enable CPUidle for the ux500, it has been accidentally
disabled due to a Kconfig change.
* tag 'ux500-defconfig-v3.13-rcs' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: u8500_defconfig: add missing cpuidle option
u8500_defconfig: allow creation and mounting of devtmpfs
- Restore platform data for the (e)MMC/SD controllers, so they can
pins and special flags properly like before.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=VO2C
-----END PGP SIGNATURE-----
Merge tag 'ux500-fixes-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij, Ux500 fixes for the v3.13 series:
- Restore platform data for the (e)MMC/SD controllers, so they can
pins and special flags properly like before.
* tag 'ux500-fixes-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
Revert "ARM: ux500: Stop passing MMC's platform data for Device Tree boots"
Revert "ARM: ux500: Remove AUXDATA relating to SDI (MMC) clock-name bindings"
This reverts commit 49c129519a.
The special settings for the SD/MMC card parameters that are not
yet fully agreed upon how to encode into the device tree went missing
with this commit. We need to first put it into the device tree,
and then remove the platform data.
Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit ce16feb851.
This commit stopped tying down the name of the MMC/SD devices, but these
names are used in the pin control table, so the MMC/SD cards stopped
working.
Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the commit d3f2950f2a, the option
ARM_U8500_CPUIDLE was added to the Kconfig but not reflected in the
default config file, hence the cpuidle driver is no longer enabled
since this commit.
Enable it again by adding the missing option in the default config file.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables CONFIG_DETTMPFS and CONFIG_DEVTMPFS_MOUNT
flags for u8500 based devices.
In this way it's possible to create a tmpfs/ramfs already in the
early stages of the boot, allowing programs like udev/mdev to
populate the /dev directory.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on OMAP,
finding new breakage of things that don't work quite right yet without
the traditional board files. I expect a bit more of this to come in this
release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec work and
to stop the MCPM core to produce a warning (the warning was new to 3.13-rc1).
- A handful of minor fixes for various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zdhe
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on
OMAP, finding new breakage of things that don't work quite right
yet without the traditional board files. I expect a bit more of
this to come in this release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec
work and to stop the MCPM core to produce a warning (the warning
was new to 3.13-rc1).
- A handful of minor fixes for various platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm2835: add missing #xxx-cells to I2C nodes
ARM: dts: Add max77686 RTC interrupt to cros5250-common
ARM: vexpress/TC2: Implement MCPM power_down_finish()
ARM: tegra: Provide dummy powergate implementation
ARM: omap: fix warning with LPAE build
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: imx6qdl: disable spdif "rxtx5" clock option
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
