Use the new fail-safe channels switch mechanism to set new ethtool
settings:
- ring parameters
- coalesce parameters
- tx copy break parameters
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
A fail safe helper functions that allows switching to new channels on the
fly, In simple words:
make_new_config(new_params)
{
new_channels = open_channels(new_params);
if (!new_channels)
return "Failed, but current channels are still active :)"
switch_channels(new_channels);
return "SUCCESS";
}
Demonstrate mlx5e_switch_priv_channels usage in set channels ethtool
callback and make it fail-safe using the new switch channels mechanism.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
mlx5e_redirect_rqts_to_{channels,drop} and mlx5e_{add,del}_sqs_fwd_rules
and Set real num tx/rx queues belong to
mlx5e_{activate,deactivate}_priv_channels, for that we move those functions
and minimize mlx5e_open/close flows.
This will be needed in downstream patches to replace old channels with new
ones without the need to call mlx5e_close/open.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Remove mlx5e_priv pointer from CQ and RQ structs,
it was needed only to access mdev pointer from priv pointer.
Instead we now pass mdev where needed.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
In order to have a clean separation between channels resources creation
flows and current active mlx5e netdev parameters, make sure each
resource creation function do not access priv->params, and only works
with on a new fresh set of parameters.
For this we add "new" mlx5e_params field to mlx5e_channels structure
and use it down the road to mlx5e_open_{cq,rq,sq} and so on.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
As a foundation for safe config flow, a simple clear API such as
(Open then Activate) where the "Open" handles the heavy unsafe
creation operation and the "activate" will be fast and fail safe,
to enable the newly created channels.
For this we split the RQs/TXQ SQs and channels open/close flows to
open => activate, deactivate => close.
This will simplify the ability to have fail safe configuration changes
in downstream patches as follows:
make_new_config(new_params)
{
old_channels = current_active_channels;
new_channels = create_channels(new_params);
if (!new_channels)
return "Failed, but current channels still active :)"
deactivate_channels(old_channels); /* Can't fail */
activate_channels(new_channels); /* Can't fail */
close_channels(old_channels);
current_active_channels = new_channels;
return "SUCCESS";
}
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Rename mlx5e_refresh_tirs_self_loopback to mlx5e_refresh_tirs,
as it will be used in downstream (Safe config flow) patches, and make it
fail safe on mlx5e_open.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
RQ Tables are always created once (on netdev creation) pointing to drop RQ
and at that stage, RQ tables (indirection tables) are always directed to
drop RQ.
We don't need to use mlx5e_fill_{direct,indir}_rqt_rqns to fill the drop
RQ in create RQT procedure.
Instead of having separate flows to redirect direct and indirect RQ Tables
to the current active channels Receive Queues (RQs), we unify the two
flows by introducing mlx5e_redirect_rqt function and redirect_rqt_param
struct. Combined, they provide one generic logic to fill the RQ table RQ
numbers regardless of the RQ table purpose (direct/indirect).
Demonstrated the usage with mlx5e_redirect_rqts_to_channels which will
be called on mlx5e_open and with mlx5e_redirect_rqts_to_drop which will
be called on mlx5e_close.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Have a dedicated "channels" handler that will serve as channels
(RQs/SQs/etc..) holder to help with separating channels/parameters
operations, for the downstream fail-safe configuration flow, where we will
create a new instance of mlx5e_channels with the new requested parameters
and switch to the new channels on the fly.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
To simplify mlx5e_open_locked flow we set netdev->rx_cpu_rmap on netdev
creation rather on netdev open, it is redundant to set it every time on
mlx5e_open_locked.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Instead of iterating over the channel SQs to set their max rate, do it
on SQ creation per TXQ SQ.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Currently the return allocated index and err value are multiplexed.
This patch changes the API to decouple the ret value from the allocated
index.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different SQ types (tx, xdp, ico) are growing apart, we separate them
and remove unwanted parts in each one of them, to simplify data path and
utilize data cache.
Remove DB union from SQ structures since it is not needed anymore as we
now have different SQ data type for each SQ.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patches we will introduce different SQ types,
and we would want to reuse those functions, in this patch we make them
agnostic to SQ type (txq, xdp, ico).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mlx5e_{create,destroy}_{sq,rq,cq} to
mlx5e_{alloc,free}_{sq,rq,cq}.
Rename mlx5e_{enable,disable}_{sq,rq,cq} to
mlx5e_{create,destroy}_{sq,rq,cq}.
mlx5e_{enable,disable}_{sq,rq,cq} used to actually create/destroy the SQ
in FW, so we rename them to align the functions names with FW semantics.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patches we will introduce different SQ types, for that we here
generalize some TX helper functions to work with more basic SQ parameters,
in order to re-use them for the different SQ types.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP SQ has a fixed size WQE (MLX5E_XDP_TX_WQEBBS = 1) and only posts
one kind of WQE (MLX5_OPCODE_SEND),
Also we initialize SQ descriptors static fields once on open_xdpsq,
rather than every time on critical path.
Optimize the code in light of those facts and add a prefetch of the TX
descriptor first thing in the xdp xmit function.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Before Now improvement
---------------------------------------------------------------
XDP TX (1 core) 13Mpps 13.7Mpps 5%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle XDP TX completions before handling RX packets, to make sure more
free space is available for XDP TX packets a moment before handling
RX packets.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Before Now improvement
---------------------------------------------------------------
XDP Drop (1 core) 16.9Mpps 16.9Mpps No change
XDP TX (1 core) 12Mpps 13Mpps 8%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To save many rq->channel->sq dereferences in fast-path.
And rename it to xdpsq.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move struct mlx5e_rq and friends to appear after mlx5e_sq declaration in
en.h.
We will need this for next patch to move the mlx5e_sq instance into
mlx5e_rq struct for XDP SQs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP code belongs to RX path, move mlx5e_poll_xdp_tx_cq and
mlx5e_free_xdp_tx_descs to en_rx.c.
Rename them to mlx5e_poll_xdpsq_cq and mlx5e_free_xdpsq_descs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One is sufficient since Blue Flame is not supported anymore.
This will also come in handy for switchdev mode to save resources, since
VF representors will use same single UAR as well for their own SQs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5e netdev Blue Flame (write combining) support demands a lot of
overhead for a little latency gain for some special cases, this overhead
is hurting the common case.
Here we remove xmit Blue Flame support by creating all bfregs with no
write combining for all SQs, and we remove a lot of BF logic and
conditions from xmit data path.
Simplify mlx5e_tx_notify_hw (doorbell function) by removing BF related
code and by removing one memory barrier needed for WC mapped SQ doorbell
buffers, which no longer exist.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Before Now improvement
---------------------------------------------------------------
TX packets (24 threads) 50Mpps 54Mpps 8%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_rmb in mlx5e_get_cqe rather than aggressive rmb (at least on
some architectures), this should help improve the performance on such
CPU archs where dma_rmb is optimized.
Performance improvement:
System: Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
Test case Baseline Now improvement
---------------------------------------------------------------
TX packets (24 threads) 45Mpps 50Mpps 11%
TC stack Drop (1 core) 3.45Mpps 3.6Mpps 5%
XDP Drop (1 core) 14Mpps 16.9Mpps 20%
XDP TX (1 core) 10.4Mpps 12Mpps 15%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in the previous patch, the cell size may change in future
devices, so query it from the firmware instead of hard coding it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sizes and thresholds of the priority group (PG) buffers are
configured in cells, which represent a specific amount of bytes.
The cell size can vary in different devices, so it's better to query it
from the firmware than hard coding it.
Refactor the code dealing with this value into different functions, so
that it will be easier to make the conversion in the next patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of hard coding the size of the shared buffer in the driver,
query it from the firmware, as it may change in future devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently hard code the maximum number of ports in the driver, but
this may change in future devices, so query it from the firmware
instead.
Fallback to a maximum of 64 ports in case this number can't be queried.
This should only happen in SwitchX-2 for which this number is correct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of hard coding the number of LPM trees in the driver, query it
from the firmware, as it may change in future devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use it during development and we can't extend it either, so
remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 435277
rx_lro_packets: 35847
rx_packets_phy: 1935066
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 61340
tx_tso_packets: 60954
tx_packets_phy: 2451115
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was added to allow the TC offloading code to identify offloading
encap/decap vxlan rules.
The VF reps are effectively related to the same mlx5 PCI device as the
PF. Since the kernel invokes the (say) delete ndo for each netdev, the
FW erred on multiple vxlan dst port deletes when the port was deleted
from the system.
We fix that by keeping the registration to be carried out only by the
PF. Since the PF serves as the uplink device, the VF reps will look
up a port there and realize if they are ok to offload that.
Tested:
<SETUP VFS>
<SETUP switchdev mode to have representors>
ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999
ip link set vxlan1 up
ip link del dev vxlan1
Fixes: 4a25730eb2 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use the non UAPI values and we miss erring on
the modify action which is not supported, fix that.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the eswitch inline mode can potentially cause already configured
flows not to match the policy. E.g. set policy L4, add some L4 rules,
set policy to L2 --> bad! Hence we disallow it.
Keep track of how many offloaded rules are now set and refuse
inline mode changes if this isn't zero.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch
offloading use case, and push the latter into the e-switch code. This provides
better separation and is to be used in down-stream patch for applying a fix.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23 ('net/mlx5: Rate limit tables support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arguments packets and bytes to call mlxsw_sp_acl_rule_get_stats are
in the wrong order. Fix this by swapping them.
Detected by CoverityScan, CID#1419705 ("Arguments in wrong order")
Fixes: 7c1b8eb175 ("mlxsw: spectrum: Add support for TC flower offload statistics")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the default case for matchall offload with what's there
for flower.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the struct representing router interface "mlxsw_sp_rif"
is reffered as "r" in various places in the driver. Furthermore it
contains a member which specify the index which is called "rif".
This patch change "r" to "rif" and "rif" to "rif_index".
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
For such Hypervisors, there is a race condition between the VF's
shutdown method and its internal-error detection/reset thread.
The internal-error detection/reset thread (which runs every 5 seconds) also
detects a disabled comm channel. If the internal-error detection/reset
flow wins the race, we still get delays (while that flow tries repeatedly
to detect comm-channel recovery).
The cited commit fixed the command timeout problem when the
internal-error detection/reset flow loses the race.
This commit avoids the unneeded delays when the internal-error
detection/reset flow wins.
Fixes: d585df1c5c ("net/mlx4_core: Avoid command timeouts during VF driver device shutdown")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: Simon Xiao <sixiao@microsoft.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that port netdevs can be enslaved to a VRF master we need to make
sure the device's routing tables won't be flushed upon the insertion of
a l3mdev rule.
Note that we assume the notified l3mdev rule is a simple rule as used by
the VRF master. We don't check for the presence of other selectors such
as 'iif' and 'oif'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to the previous patch, allow bridges and VLAN
devices on top of bridges to be enslaved to a VRF master device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow port netdevs, LAG and VLAN devices stacked on top of these to be
enslaved to a VRF master device.
Upon enslavement, create a router interface (RIF) for the enslaved
netdev and associate it with a virtual router (VR) based on the VRF's
table ID.
If a RIF already exists for the netdev (f.e., due to the existence of an
IP address), then it's deleted and a new one is created with the
appropriate VR binding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We usually destroy the netdev's router interface (RIF) when the last IP
address is removed from it.
However, we shouldn't do that if it's enslaved to an L3 master device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a router interface (RIF) is created due to a netdev being enslaved
to a VRF master, then it should be associated with the appropriate
virtual router (VR) and not the default one.
If netdev is a VRF slave, lookup the VR based on the VRF's table ID.
Otherwise default to the MAIN table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit c3852ef7f2 ("ipv4: fib: Replay events when registering FIB
notifier") we dumped the FIB tables and replayed the events to the
passed notification block.
However, we merely sent a RULE_ADD notification in case custom rules
were in use. As explained in previous patches, this approach won't work
anymore. Instead, we should notify the caller about all the FIB rules
and let it act accordingly.
Upon registration to the FIB notification chain, replay a RULE_ADD
notification for each programmed FIB rule, custom or not. The integrity
of the dump is ensured by the mechanism introduced in the above
mentioned commit.
Prevent regressions by making sure current listeners correctly sanitize
the notified rules.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
