Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-08-15
This series contains fixes to i40e only.
Anjali provides two fixes for i40e, first adds a check for non-active
VF before sending admin queue messages to the VFS. This resolves a
potential kernel panic which would happen whenever we got a Tx hang and
there were VFS that were not up or enabled. The second fix adds
additional checks so that we do try to access a VF that is not up or
enabled which would dereference a null pointer.
Jesse fixes a i40e PTP bug where the hang detection routine was never
being run when PTP was enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7xxx internal Gigabit PHY on 28nm process do not need anything
special to be done during suspend, remove the suspend callback since it
might be harmful rather than useful. While at it, update the comment
above bcm7xxx_suspend() to reflect that it applies only to 40nm and 65nm
process PHY devices.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
The BCM7xxx internal Gigabit PHYs on 28nm process platforms come out
reset without any half-duplex or "hub" compatible advertised modes,
which was causing auto-negotiation issues coming out of S3
suspend/resume, we just could not establish a link with a half-duplex
only link partner.
Make sure that the resume function properly re-configures the PHY device
to advertise all supported modes.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
The receive hang detection routine was never being run when
PTP was enabled.
Change-ID: I200f35b0f3190d31b595df89d678f4c8a2131ba0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some functions we might be doing potential dereference
without a check. This patch puts the check in place for all these
functions. Also fix the "for loops" so that we increment VF at the
right place so that we always do it even if we are short-circuiting
the loop through continue.
Change-ID: Id4276cfb1e841031bb7b6d6790c414242f364a9f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whenever we get a Tx hang we issue a PFR, which means we send AQ
messages to VFS about the reset coming. Unfortunately with the recent
fix to be able to send messages to all VFS which earlier was not
happening at all we now are sending messages to not just the VFS that
are up but also to VFS that are not up. AQ complains about this and
sends us an error in ARQ called LAN overflow event for a queue. We
check if the queue belongs to a VF and if it does we try to send a
vc_notify_vf_reset message to that VF. Well if the VF is not up/enabled
we will be entering this function with a non-active VF id. In this
function we were assuming VF struct is populated but it won't be if
the VF is not active.
Change-ID: Ic6733cda4582d3609fe6d83b2872bb2dcdc73f4a
Signed-off-by: Ashish N Shah <ashish.n.shah@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- Fix for an ACPI-based device hotplug regression introduced in 3.14
that causes a kernel panic to trigger when memory hot-remove is
attempted with CONFIG_ACPI_HOTPLUG_MEMORY unset from Tang Chen.
- Fix for a cpufreq regression introduced in 3.16 that triggers a
"sleeping function called from invalid context" bug in
dev_pm_opp_init_cpufreq_table() from Stephen Boyd.
- ACPI battery driver fix for a warning message added in 3.16 that
prints silly stuff sometimes from Mariusz Ceier.
- Hibernation fix for safer handling of mismatches in the 820 memory
map between the configurations during image creation and during
the subsequent restore from Chun-Yi Lee.
- ACPI processor driver fix to handle CPU hotplug notifications
correctly during system suspend/resume from Lan Tianyu.
- Series of four cpuidle menu governor cleanups that also should
speed it up a bit from Mel Gorman.
- Fixes for the speedstep-smi, integrator, cpu0 and arm_big_little
cpufreq drivers from Hans Wennborg, Himangi Saraogi, Markus Pargmann
and Uwe Kleine-König.
- Version 3.0 of the analyze_suspend.py suspend profiling tool
from Todd E Brandt.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=kpiw
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are a couple of regression fixes, cpuidle menu governor
optimizations, fixes for ACPI proccessor and battery drivers,
hibernation fix to avoid problems related to the e820 memory map,
fixes for a few cpufreq drivers and a new version of the suspend
profiling tool analyze_suspend.py.
Specifics:
- Fix for an ACPI-based device hotplug regression introduced in 3.14
that causes a kernel panic to trigger when memory hot-remove is
attempted with CONFIG_ACPI_HOTPLUG_MEMORY unset from Tang Chen
- Fix for a cpufreq regression introduced in 3.16 that triggers a
"sleeping function called from invalid context" bug in
dev_pm_opp_init_cpufreq_table() from Stephen Boyd
- ACPI battery driver fix for a warning message added in 3.16 that
prints silly stuff sometimes from Mariusz Ceier
- Hibernation fix for safer handling of mismatches in the 820 memory
map between the configurations during image creation and during the
subsequent restore from Chun-Yi Lee
- ACPI processor driver fix to handle CPU hotplug notifications
correctly during system suspend/resume from Lan Tianyu
- Series of four cpuidle menu governor cleanups that also should
speed it up a bit from Mel Gorman
- Fixes for the speedstep-smi, integrator, cpu0 and arm_big_little
cpufreq drivers from Hans Wennborg, Himangi Saraogi, Markus
Pargmann and Uwe Kleine-König
- Version 3.0 of the analyze_suspend.py suspend profiling tool from
Todd E Brandt"
* tag 'pm+acpi-3.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / battery: Fix warning message in acpi_battery_get_state()
PM / tools: analyze_suspend.py: update to v3.0
cpufreq: arm_big_little: fix module license spec
cpufreq: speedstep-smi: fix decimal printf specifiers
ACPI / hotplug: Check scan handlers in acpi_scan_hot_remove()
cpufreq: OPP: Avoid sleeping while atomic
cpufreq: cpu0: Do not print error message when deferring
cpufreq: integrator: Use set_cpus_allowed_ptr
PM / hibernate: avoid unsafe pages in e820 reserved regions
ACPI / processor: Make acpi_cpu_soft_notify() process CPU FROZEN events
cpuidle: menu: Lookup CPU runqueues less
cpuidle: menu: Call nr_iowait_cpu less times
cpuidle: menu: Use ktime_to_us instead of reinventing the wheel
cpuidle: menu: Use shifts when calculating averages where possible
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
Pull networking fixes from David Miller:
"I'm sending this out, in particular, to get the iwlwifi fix
propagated:
1) Fix build due to missing include in i40e driver, from Lucas
Tanure.
2) Memory leak in openvswitch port allocation, from Chirstoph Jaeger.
3) Check DMA mapping errors in myri10ge, from Stanislaw Gruszka.
4) Fix various deadlock scenerios in sunvnet driver, from Sowmini
Varadhan.
5) Fix cxgb4i build failures with incompatible Kconfig settings of
the driver vs ipv6, from Anish Bhatt.
6) Fix generation of ACK packet timestamps in the presence of TSO
which will be split up, from Willem de Bruijn.
7) Don't enable sched scan in iwlwifi driver, it causes firmware
crashes in some revisions. From Emmanuel Grumbach.
8) Revert a macvlan simplification that causes crashes.
9) Handle RTT calculations properly in the presence of repair'd SKBs,
from Andrey Vagin.
10) SIT tunnel lookup uses wrong device index in compares, from
Shmulik Ladkani.
11) Handle MTU reductions in TCP properly for ipv4 mapped ipv6
sockets, from Neal Cardwell.
12) Add missing annotations in rhashtable code, from Thomas Graf.
13) Fix false interpretation of two RTOs as being from the same TCP
loss event in the FRTO code, from Neal Cardwell"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
netlink: Annotate RCU locking for seq_file walker
rhashtable: fix annotations for rht_for_each_entry_rcu()
rhashtable: unexport and make rht_obj() static
rhashtable: RCU annotations for next pointers
tcp: fix ssthresh and undo for consecutive short FRTO episodes
tcp: don't allow syn packets without timestamps to pass tcp_tw_recycle logic
tcp: fix tcp_release_cb() to dispatch via address family for mtu_reduced()
sit: Fix ipip6_tunnel_lookup device matching criteria
net: ethernet: ibm: ehea: Remove duplicate object from Makefile
net: xgene: Check negative return value of xgene_enet_get_ring_size()
tcp: don't use timestamp from repaired skb-s to calculate RTT (v2)
net: xilinx: Remove .owner field for driver
Revert "macvlan: simplify the structure port"
iwlwifi: mvm: disable scheduled scan to prevent firmware crash
xen-netback: remove loop waiting function
xen-netback: don't stop dealloc kthread too early
xen-netback: move NAPI add/remove calls
xen-netback: fix debugfs entry creation
xen-netback: fix debugfs write length check
net-timestamp: fix missing tcp fragmentation cases
...
John W. Linville says:
====================
pull request: wireless 2014-08-14
Please pull this batch of fixes intended for the 3.17 stream...
Arend van Spriel brings two brcmfmac fixes, one which fixes a memory
leak and one which corrects some merge damage.
Emmanuel Grumbach fixes Linus's iwlwifi firmware-related log spam.
Rickard Strandqvist does some proper NULL termination after a call
to strncpy.
Ronald Wahl corrects a carl9170 problem with sending URBs with the
wrong endpoint type (resulting in log spam).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Makefile, ehea_phyp.o is included twice in the list of
object files compile into ehea.o.
This change removes one instance.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
xgene_enet_get_ring_size() returns a negative value in case of an error,
but its only caller in xgene_enet_create_desc_ring() currently uses the
return value directly as u32. Instead, check for a negative value first and
error out in case. Also move the call to xgene_enet_get_ring_size() before
devm_kzalloc() so we don't need to free anything in the error path.
This fixes the following issue reported by the Coverity Scanner:
** CID 1231336: Improper use of negative value (NEGATIVE_RETURNS)
/drivers/net/ethernet/apm/xgene/xgene_enet_main.c: 596 in xgene_enet_create_desc_ring()
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wOm0
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
"Main set of InfiniBand/RDMA updates for 3.17 merge window:
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes..."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (52 commits)
IB/srp: Fix return value check in srp_init_module()
RDMA/ocrdma: report asic-id in query device
RDMA/ocrdma: Update sli data structure for endianness
RDMA/ocrdma: Obtain SL from device structure
RDMA/uapi: Include socket.h in rdma_user_cm.h
IB/srpt: Handle GID change events
IB/mlx5: Use ARRAY_SIZE instead of sizeof/sizeof[0]
IB/mlx4: Use ARRAY_SIZE instead of sizeof/sizeof[0]
RDMA/amso1100: Check for integer overflow in c2_alloc_cq_buf()
IPoIB: Remove unnecessary test for NULL before debugfs_remove()
IB/mad: Add user space RMPP support
IB/mad: add new ioctl to ABI to support new registration options
IB/mad: Add dev_notice messages for various umad/mad registration failures
IB/mad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid multicast join attempts with invalid P_key
IB/umad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid flushing the workqueue from worker context
IB/ipoib: Use P_Key change event instead of P_Key polling mechanism
IB/ipath: Add P_Key change event support
mlx4_core: Add support for secure-host and SMP firewall
...
Merge leftovers from Andrew Morton:
"A few leftovers.
I have a bunch of OCFS2 patches which are still out for review and
which I might sneak along after -rc1. Partly my fault - I should send
my review pokes out earlier"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: fix CROSS_MEMORY_ATTACH help text grammar
drivers/mfd/rtsx_usb.c: export device table
mm, hugetlb_cgroup: align hugetlb cgroup limit to hugepage size
The rtsx_usb driver contains the table for the devices it supports but
doesn't export it. As a result, no alias is generated and it doesn't
get loaded automatically.
Via https://bugzilla.novell.com/show_bug.cgi?id=890096
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: Marcel Witte <wittemar@googlemail.com>
Cc: Roger Tseng <rogerable@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are firmwares which don't support scheduled scan.
Disable it for now.
Linus's system encoutered this issue.
Thanks to David Spinadel for his help.
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of error, the function create_workqueue() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
window:
Group changes to the device tree. In preparation for adding device tree
overlay support, OF_DYNAMIC is reworked so that a set of device tree
changes can be prepared and applied to the tree all at once. OF_RECONFIG
notifiers see the most significant change here so that users always get
a consistent view of the tree. Notifiers generation is moved from before
a change to after it, and notifiers for a group of changes are emitted
after the entire block of changes have been applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART devices
get this support automatically when uart_add_one_port() is called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then unloaded
again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8IFz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
- Enable support for bus reset on device release
- Fixes for EEH support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT64V6AAoJECObm247sIsimLkQAKL8sdGu2xwjujB/JFQrTXq0
9jN42aNhv50fVE9p2FKoqet/6VlQmRxLUvA9By94iMIKsUb3w0Rziti1FI3iyKtb
7lPzhCY9GWFnMD7Ero0nx+ljYrDiMlDdjeJ1ke25f1WZKMv524FJvA3cbiCvnAm0
3CRV0buq69deiiy5j1dbJdwYfPTJU7Jepqg8/OkjgJYokKRwqng9QfUgRbNwfL5d
FuVWaiGKvkxj4Sil0M3m4Ogf2yqqweX0am/rC3pGoO9woc9XFV560ABoEvXe3PI/
TPq3X63eqiBtu+t0qnYdi9jAfV62NMQEOwgb1z3IrIRoR9pwCOR2UFVQSr9X+rMp
EGrGUNkgU9cTzGeiSPmTII/ccYgsFpivy2UV+lNeDs4kraU++Q3QoJ2jwbzx8unF
nzyEfW8BizUenBZHsLvBDrlDddn5uEgao9ivdc9yBhjtOQshA8xMUKFG1PHzqtYg
Vis9/K2TKrZBcQTBD7nwCWWPLUg11N7stD6Ui0DEAEqJtGWxCNSqcKGTen1NvsOp
hpFdlySYORNvPQDMMBmjMc+YkngBwcwDaITE5FFMbyDJYymKA28MtkYaDVLZp5kZ
yYua3afxxDDaAzh7ikzUMpBlsSxbRpanAeTtEMQ0s2+ZfkzdvKztmTe9S26swQXG
p9hb4pIJNflk014lnNt1
=ADuE
-----END PGP SIGNATURE-----
Merge tag 'vfio-v3.17-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- enable support for bus reset on device release
- fixes for EEH support
* tag 'vfio-v3.17-rc1' of git://github.com/awilliam/linux-vfio:
drivers/vfio: Enable VFIO if EEH is not supported
drivers/vfio: Allow EEH to be built as module
drivers/vfio: Fix EEH build error
vfio-pci: Attempt bus/slot reset on release
vfio-pci: Use mutex around open, release, and remove
vfio-pci: Release devices with BusMaster disabled
allow thin snapshots to be larger than the external origin.
. Add support for quickly loading a repetitive pattern into the
dm-switch target.
. Use per-bio data in the dm-crypt target instead of always using a
mempool for each allocation. Required switching to kmalloc alignment
for the bio slab.
. Fix DM core to properly stack the QUEUE_FLAG_NO_SG_MERGE flag
. Fix the dm-cache and dm-thin targets' export of the minimum_io_size to
match the data block size -- this fixes an issue where mkfs.xfs would
improperly infer raid striping was in place on the underlying storage.
. Small cleanups in dm-io, dm-mpath and dm-cache
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT64yEAAoJEMUj8QotnQNatjQH/2mqm8EtPuZas70zHVDzjMlE
ZyV8xgHpU0MBmiBi+JhUBv9iKX4sVa+C25559WkKtxRVMnZmI1WDry4TagiqrhnK
9o/uvdWigJMR+uwahwe4UErEtKscOQJD30a8taN/suJ6Z2C7XJJRUZPsyL4a3Vov
w+UIi7aYDEGp/2VQ8mvTTxjdF5x5km4wKsjBTs03uTrrkEJ+bIUndl2I1X+X4bsw
kiWYOQwmcnD8GwYkSrthJYLsS3Hjur/J/My7KZwXc00ANLOexqHdKfRDwH8b36+m
olKXv3swCd8vi+jJYEYzuW9213ACsSEGP7h8NFVZ/+2FeDsSzB/C7zjW9okIUIw=
=y/3r
-----END PGP SIGNATURE-----
Merge tag 'dm-3.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper changes from Mike Snitzer:
- Allow the thin target to paired with any size external origin; also
allow thin snapshots to be larger than the external origin.
- Add support for quickly loading a repetitive pattern into the
dm-switch target.
- Use per-bio data in the dm-crypt target instead of always using a
mempool for each allocation. Required switching to kmalloc alignment
for the bio slab.
- Fix DM core to properly stack the QUEUE_FLAG_NO_SG_MERGE flag
- Fix the dm-cache and dm-thin targets' export of the minimum_io_size
to match the data block size -- this fixes an issue where mkfs.xfs
would improperly infer raid striping was in place on the underlying
storage.
- Small cleanups in dm-io, dm-mpath and dm-cache
* tag 'dm-3.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm table: propagate QUEUE_FLAG_NO_SG_MERGE
dm switch: efficiently support repetitive patterns
dm switch: factor out switch_region_table_read
dm cache: set minimum_io_size to cache's data block size
dm thin: set minimum_io_size to pool's data block size
dm crypt: use per-bio data
block: use kmalloc alignment for bio slab
dm table: make dm_table_supports_discards static
dm cache metadata: use dm-space-map-metadata.h defined size limits
dm cache: fail migrations in the do_worker error path
dm cache: simplify deferred set reference count increments
dm thin: relax external origin size constraints
dm thin: switch to an atomic_t for tracking pending new block preparations
dm mpath: eliminate pg_ready() wrapper
dm io: simplify dec_count and sync_io
- Forward compatibility for eMMC.
- Fix some blacklisted cards with broken secure discard.
MMC host:
- mmci: Add support for Qualcomm variant.
- mmci: Fix regression for arm_variant.
- sdhci: Various fixes and cleanups.
- sdhci: Improve external VDD regulator support.
- sdhci: Support for DDR50 1.8V mode for BayTrail.
- sdhci-st: Add driver for ST SDHCI controller.
- sh-mmcif: DMA fixes.
- omap_hsmmc: Add support for SDIO interrupts.
- sdhci-pci: Add support for Intel Quark X1000.
- dw_mmc: Update the reset sequence.
- s3cmci: port DMA code to dmaengine API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kGSY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"Me and Chris Ball decided to try out using my MMC tree as the primary
one, to simplify handling of patches.
This pull does thus contains all the MMC patches for 3.17 rc1, no pull
from Chris this time.
Details:
MMC core:
- forward compatibility for eMMC
- fix some blacklisted cards with broken secure discard
MMC host:
- mmci: Add support for Qualcomm variant
- mmci: Fix regression for arm_variant
- sdhci: Various fixes and cleanups
- sdhci: Improve external VDD regulator support
- sdhci: Support for DDR50 1.8V mode for BayTrail
- sdhci-st: Add driver for ST SDHCI controller
- sh-mmcif: DMA fixes
- omap_hsmmc: Add support for SDIO interrupts
- sdhci-pci: Add support for Intel Quark X1000
- dw_mmc: Update the reset sequence
- s3cmci: port DMA code to dmaengine API"
* tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
mmc: dw_mmc: modify the dt-binding for removing slot-node and supports-highspeed
mmc: dw_mmc: Slot quirk "disable-wp" is deprecated.
mmc: mmci: Reverse IRQ handling for the arm_variant
mmc: mmci: Move all CMD irq handling to mmci_cmd_irq()
mmc: mmci: Remove redundant check of status for DATA irq
mmc: dw_mmc: change to use recommended reset procedure
mmc: sdhci-pxav3: Use devm_* managed helpers
mmc: tmio: Configure DMA slave bus width
mmc: sh_mmcif: Configure DMA slave bus width
mmc: sh_mmcif: Fix DMA slave address configuration
mmc: sh_mmcif: Document DT bindings
mmc: sdhci-pci: remove PCI PM functions in suspend/resume callback
mmc: Do not advertise secure discard if it is blacklisted
mmc: sdhci-msm: Get COMPILE_TEST support
mmc: sdhci-msm: Remove unnecessary header file inclusion
mmc: sdhci-msm: Fix the binding example
mmc: sdhci: add DDR50 1.8V mode support for BayTrail eMMC Controller
mmc: sdhci: Preset value not supported in Baytrail eMMC
mmc: MMC_USDHI6ROL0 should depend on HAS_DMA
mmc: MMC_SH_MMCIF should depend on HAS_DMA
...
Pull block driver changes from Jens Axboe:
"Nothing out of the ordinary here, this pull request contains:
- A big round of fixes for bcache from Kent Overstreet, Slava Pestov,
and Surbhi Palande. No new features, just a lot of fixes.
- The usual round of drbd updates from Andreas Gruenbacher, Lars
Ellenberg, and Philipp Reisner.
- virtio_blk was converted to blk-mq back in 3.13, but now Ming Lei
has taken it one step further and added support for actually using
more than one queue.
- Addition of an explicit SG_FLAG_Q_AT_HEAD for block/bsg, to
compliment the the default behavior of adding to the tail of the
queue. From Douglas Gilbert"
* 'for-3.17/drivers' of git://git.kernel.dk/linux-block: (86 commits)
bcache: Drop unneeded blk_sync_queue() calls
bcache: add mutex lock for bch_is_open
bcache: Correct printing of btree_gc_max_duration_ms
bcache: try to set b->parent properly
bcache: fix memory corruption in init error path
bcache: fix crash with incomplete cache set
bcache: Fix more early shutdown bugs
bcache: fix use-after-free in btree_gc_coalesce()
bcache: Fix an infinite loop in journal replay
bcache: fix crash in bcache_btree_node_alloc_fail tracepoint
bcache: bcache_write tracepoint was crashing
bcache: fix typo in bch_bkey_equal_header
bcache: Allocate bounce buffers with GFP_NOWAIT
bcache: Make sure to pass GFP_WAIT to mempool_alloc()
bcache: fix uninterruptible sleep in writeback thread
bcache: wait for buckets when allocating new btree root
bcache: fix crash on shutdown in passthrough mode
bcache: fix lockdep warnings on shutdown
bcache allocator: send discards with correct size
bcache: Fix to remove the rcu_sched stalls.
...
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-08-12
This series contains updates to i40e and e1000e.
Lucas provides a fix for i40e to resolve a compile issue where a header
was missing in the #includes.
Wei Yongjun provides a fix for i40e to resolve a sparse warning, where
a non-static function should be static.
Julia Lawall provides a fix for i40e which was found using Coccinelle,
where there was a typo in the name of the type given to sizeof().
Rickard Strandqvist provides a fix for i40e to replace the use of
strncpy() with strlcpy() to avoid strings that lack null termination.
Jean Sacren provides two e1000e fixes, first is a comment fix and second
removes an excessive space character in a debug message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The original implementation relies on a loop to check if all inflight
packets are freed. Now we have proper reference counting, there's no
need to use loop anymore.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reference count the number of packets in host stack, so that we don't
stop the deallocation thread too early. If not, we can end up with
xenvif_free permanently waiting for deallocation thread to unmap grefs.
Reported-by: Thomas Leonard <talex5@gmail.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally netif_napi_add was in xenvif_init_queue and netif_napi_del
was in xenvif_deinit_queue, while kthreads were handled in
xenvif_connect and xenvif_disconnect. Move netif_napi_add and
netif_napi_del to xenvif_connect and xenvif_disconnect so that they
reside together with kthread operations.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code is bogus. The function gets called in a loop which
leaks entries created in previous rounds.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enlarge buffer size and check input length properly, so that we don't
misuse -ENOSPC.
Note that command like "kickXXXX" is still allowed, that's one patch for
another day if we really want to be very strict on this.
Reported-by: SeeChen Ng <seechen81@gmail.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous guard of IS_ENABLED(CONFIG_IPV6) is not sufficient when cxgbi drivers
are built into kernel but ipv6 is not.
v2: Use Kconfig to disable compiling cxgbi built into kernel when ipv6 is
compiled as a module
Fixes: e81fbf6cd6 ("libcxgbi:cxgb4i Guard ipv6 code with a config check")
Fixes: fc8d0590d9 ("libcxgbi: Add ipv6 api to driver")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tp->hw_stats is 0, tg3_get_stats64 should display previously
recorded stats. So it returns &tp->net_stats_prev. But the caller,
dev_get_stats, ignores the return value.
Fix this by assigning tp->net_stats_prev to stats and returning stats.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the tail of vnet_event(), if we hit the maybe_tx_wakeup()
condition, we try to take the netif_tx_lock() in the
recv-interrupt-context and can deadlock with dev_watchdog().
vnet_event() should schedule maybe_tx_wakeup() as a tasklet
to avoid this deadlock
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ldc_rx -> vnet_rx -> .. -> vnet_walk_rx->vnet_send_ack should not
spin into an infinite loop waiting EAGAIN to lift.
The sender could have sent us a burst, and gone to lunch without
doing any more ldc_read()'s. That should not cause the receiver to
loop infinitely till soft-lockup kicks in.
Similarly __vnet_tx_trigger should only loop on EAGAIN a finite
number of times. The caller (vnet_start_xmit()) already has code
to reset the dring state and bail on errors from __vnet_tx_trigger
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Raghuram Kothakota <raghuram.kothakota@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to ask for an ack with every vnet_start_xmit()- the single
ACK with DRING_STOPPED is sufficient for the protocol, and we free
the sk_buff in vnet_start_xmit itself, so we dont need an ACK back.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Raghuram Kothakota <raghuram.kothakota@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On IOMMU systems DMA mapping can fail, we need to check for
that possibility.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Several networking final fixes and tidies for the merge window:
1) Changes during the merge window unintentionally took away the
ability to build bluetooth modular, fix from Geert Uytterhoeven.
2) Several phy_node reference count bug fixes from Uwe Kleine-König.
3) Fix ucc_geth build failures, also from Uwe Kleine-König.
4) Fix klog false positivies when netlink messages go to network
taps, by properly resetting the network header. Fix from Daniel
Borkmann.
5) Sizing estimate of VF netlink messages is too small, from Jiri
Benc.
6) New APM X-Gene SoC ethernet driver, from Iyappan Subramanian.
7) VLAN untagging is erroneously dependent upon whether the VLAN
module is loaded or not, but there are generic dependencies that
matter wrt what can be expected as the SKB enters the stack.
Make the basic untagging generic code, and do it unconditionally.
From Vlad Yasevich.
8) xen-netfront only has so many slots in it's transmit queue so
linearize packets that have too many frags. From Zoltan Kiss.
9) Fix suspend/resume PHY handling in bcmgenet driver, from Florian
Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (55 commits)
net: bcmgenet: correctly resume adapter from Wake-on-LAN
net: bcmgenet: update UMAC_CMD only when link is detected
net: bcmgenet: correctly suspend and resume PHY device
net: bcmgenet: request and enable main clock earlier
net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing null-terminate after strncpy call
xen-netfront: Fix handling packets on compound pages with skb_linearize
net: fec: Support phys probed from devicetree and fixed-link
smsc: replace WARN_ON() with WARN_ON_SMP()
xen-netback: Don't deschedule NAPI when carrier off
net: ethernet: qlogic: qlcnic: Remove duplicate object file from Makefile
wan: wanxl: Remove typedefs from struct names
m68k/atari: EtherNEC - ethernet support (ne)
net: ethernet: ti: cpmac.c: Cleaning up missing null-terminate after strncpy call
hdlc: Remove typedefs from struct names
airo_cs: Remove typedef local_info_t
atmel: Remove typedef atmel_priv_ioctl
com20020_cs: Remove typedef com20020_dev_t
ethernet: amd: Remove typedef local_info_t
net: Always untag vlan-tagged traffic on input.
drivers: net: Add APM X-Gene SoC ethernet driver support.
...
Pull x86/apic updates from Thomas Gleixner:
"This is a major overhaul to the x86 apic subsystem consisting of the
following parts:
- Remove obsolete APIC driver abstractions (David Rientjes)
- Use the irqdomain facilities to dynamically allocate IRQs for
IOAPICs. This is a prerequisite to enable IOAPIC hotplug support,
and it also frees up wasted vectors (Jiang Liu)
- Misc fixlets.
Despite the hickup in Ingos previous pull request - caused by the
missing fixup for the suspend/resume issue reported by Borislav - I
strongly recommend that this update finds its way into 3.17. Some
history for you:
This is preparatory work for physical IOAPIC hotplug. The first
attempt to support this was done by Yinghai and I shot it down because
it just added another layer of obscurity and complexity to the already
existing mess without tackling the underlying shortcomings of the
current implementation.
After quite some on- and offlist discussions, I requested that the
design of this functionality must use generic infrastructure, i.e.
irq domains, which provide all the mechanisms to dynamically map linux
interrupt numbers to physical interrupts.
Jiang picked up the idea and did a great job of consolidating the
existing interfaces to manage the x86 (IOAPIC) interrupt system by
utilizing irq domains.
The testing in tip, Linux-next and inside of Intel on various machines
did not unearth any oddities until Borislav exposed it to one of his
oddball machines. The issue was resolved quickly, but unfortunately
the fix fell through the cracks and did not hit the tip tree before
Ingo sent the pull request. Not entirely Ingos fault, I also assumed
that the fix was already merged when Ingo asked me whether he could
send it.
Nevertheless this work has a proper design, has undergone several
rounds of review and the final fallout after applying it to tip and
integrating it into Linux-next has been more than moderate. It's the
ground work not only for IOAPIC hotplug, it will also allow us to move
the lowlevel vector allocation into the irqdomain hierarchy, which
will benefit other architectures as well. Patches are posted already,
but they are on hold for two weeks, see below.
I really appreciate the competence and responsiveness Jiang has shown
in course of this endavour. So I'm sure that any fallout of this will
be addressed in a timely manner.
FYI, I'm vanishing for 2 weeks into my annual kids summer camp kitchen
duty^Wvacation, while you folks are drooling at KS/LinuxCon :) But HPA
will have a look at the hopefully zero fallout until I'm back"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
x86, irq, PCI: Keep IRQ assignment for PCI devices during suspend/hibernation
x86/apic/vsmp: Make is_vsmp_box() static
x86, apic: Remove enable_apic_mode callback
x86, apic: Remove setup_portio_remap callback
x86, apic: Remove multi_timer_check callback
x86, apic: Replace noop_check_apicid_used
x86, apic: Remove check_apicid_present callback
x86, apic: Remove mps_oem_check callback
x86, apic: Remove smp_callin_clear_local_apic callback
x86, apic: Replace trampoline physical addresses with defaults
x86, apic: Remove x86_32_numa_cpu_node callback
x86: intel-mid: Use the new io_apic interfaces
x86, vsmp: Remove is_vsmp_box() from apic_is_clustered_box()
x86, irq: Clean up irqdomain transition code
x86, irq, devicetree: Release IOAPIC pin when PCI device is disabled
x86, irq, SFI: Release IOAPIC pin when PCI device is disabled
x86, irq, mpparse: Release IOAPIC pin when PCI device is disabled
x86, irq, ACPI: Release IOAPIC pin when PCI device is disabled
x86, irq: Introduce helper functions to release IOAPIC pin
x86, irq: Simplify the way to handle ISA IRQ
...
Pull Ceph updates from Sage Weil:
"There is a lot of refactoring and hardening of the libceph and rbd
code here from Ilya that fix various smaller bugs, and a few more
important fixes with clone overlap. The main fix is a critical change
to the request_fn handling to not sleep that was exposed by the recent
mutex changes (which will also go to the 3.16 stable series).
Yan Zheng has several fixes in here for CephFS fixing ACL handling,
time stamps, and request resends when the MDS restarts.
Finally, there are a few cleanups from Himangi Saraogi based on
Coccinelle"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (39 commits)
libceph: set last_piece in ceph_msg_data_pages_cursor_init() correctly
rbd: remove extra newlines from rbd_warn() messages
rbd: allocate img_request with GFP_NOIO instead GFP_ATOMIC
rbd: rework rbd_request_fn()
ceph: fix kick_requests()
ceph: fix append mode write
ceph: fix sizeof(struct tYpO *) typo
ceph: remove redundant memset(0)
rbd: take snap_id into account when reading in parent info
rbd: do not read in parent info before snap context
rbd: update mapping size only on refresh
rbd: harden rbd_dev_refresh() and callers a bit
rbd: split rbd_dev_spec_update() into two functions
rbd: remove unnecessary asserts in rbd_dev_image_probe()
rbd: introduce rbd_dev_header_info()
rbd: show the entire chain of parent images
ceph: replace comma with a semicolon
rbd: use rbd_segment_name_free() instead of kfree()
ceph: check zero length in ceph_sync_read()
ceph: reset r_resend_mds after receiving -ESTALE
...
fixes are:
* UBI deleted list items while iterating the list with 'list_for_each_entry'
* The UBI block driver did not work properly with very large UBI volumes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zgqa
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.17-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS changes from Artem Bityutskiy:
"No significant changes, mostly small fixes here and there. The more
important fixes are:
- UBI deleted list items while iterating the list with
'list_for_each_entry'
- The UBI block driver did not work properly with very large UBI
volumes"
* tag 'upstream-3.17-rc1' of git://git.infradead.org/linux-ubifs: (21 commits)
UBIFS: Add log overlap assertions
Revert "UBIFS: add a log overlap assertion"
UBI: bugfix in ubi_wl_flush()
UBI: block: Avoid disk size integer overflow
UBI: block: Set disk_capacity out of the mutex
UBI: block: Make ubiblock_resize return something
UBIFS: add a log overlap assertion
UBIFS: remove unnecessary check
UBIFS: remove mst_mutex
UBIFS: kernel-doc warning fix
UBI: init_volumes: Ignore volumes with no LEBs
UBIFS: replace seq_printf by seq_puts
UBIFS: replace count*size kzalloc by kcalloc
UBIFS: kernel-doc warning fix
UBIFS: fix error path in create_default_filesystem()
UBIFS: fix spelling of "scanned"
UBIFS: fix some comments
UBIFS: remove useless @ecc in struct ubifs_scan_leb
UBIFS: remove useless statements
UBIFS: Add missing break statements in dbg_chk_pnode()
...
Ocrdma does not report hw_ver when query_device is issued. This patch
adds a meaningful value to this field.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Update the sli specific mailbox command request/response data
sturcures to fix endianness issues.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, driver obtains service level value from ah_attr->sl field.
However, this field is set to zero all the times from rdma-cm. This
patch allows create_ah to obtain service level from dev->sl.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
GID change events need a refresh just like LID change events and several
others. Handle this the same as the others.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
