for weak memory model architectures to ensure that the chip will DMA
valid BD data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback on 9K packet fails because the chip has a DMA limit of 4K. The
loopback test logic uses a single BD for simplicity. Fix it by reducing
the jumbo packet size to the DMA limit.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/tg3.c
Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_get_stats64() takes tp->lock when dealing with non-serdes bcm5700
and bcm5701 devices. However, functions that call tg3_halt() have
already acquired tp->lock. When tg3_get_stats64() is called in
tg3_halt(), deadlock will occur.
This patch fixes the problem by separating the stat gathering code into
a new tg3_get_nstats() function. tg3_get_stats64() is recoded to call
this function and take tp->lock. The code that takes tp->lock in
tg3_calc_crc_errors() has been removed. Function signatures have been
cleaned up too.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch seeks to clean up the timer related code. It begins by
moving one-time timer setup code from tg3_open() to tg3_init_one().
It then creates a function that encapsulates the code needed to start
the timer. A tg3_timer_stop() function was added for parity. Finally,
this patch moves all the timer functions to a more suitable location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error happens in the tx completion thread, tg3_reset_task will be
scheduled and TX_RECOVERY_PENDING will be set. The TX_RECOVERY_PENDING
flag causes tg3_poll[_msix] to return early before doing much of its
work. Tg3_reset_task() gets canceled when the configuration of the
device is changing, which always results in a chip reset. When this
happens, the TX_RECOVERY_PENDING flag may be left set, which would
unnecessarily hinder tg3_poll from doing work. This patch fixes the
problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_phy_copper_begin() has code that configures the link
advertisements through the use of the link_config.speed and
link_config.duplex members. The driver does not internally use these
members in this way, nor is it (currently) permitted via the ethtool
interface. This patch removes the dead code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver tried to detect link changes by comparing the tg3 local
active_speed member with SPEED_UNKNOWN (or formerly SPEED_INVALID).
This check is not correct, since phylib will never set its speed member
to either of these two values. The code only appeared to work because
tg3 initializes active_speed to SPEED_INVALID during tg3_init_one. This
patch introduces a new "old_link" tg3 member and then compares the
phy_device's link member against it to detect link state changes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is the last user of the IRQF_SAMPLE_RANDOM flag for net drivers, and since add_*_randomness
interfaces have now deprecated the flag as a source of external noise, we can remove it.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the copyright dates in the tg3 driver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces tg3's private SPEED_INVALID and DUPLEX_INVALID
definitions with SPEED_UNKNOWN and DUPLEX_UNKNOWN respectively.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unneeded link_config.orig_* members. When the
phy is in a low power state, the TG3_PHYFLG_IS_LOW_POWER flag solely
determines how the link is configured. When the phy is powered back up,
it can resume using the original settings.
For the phylib case, the link configuration still needs to be saved, but
since the phylib maintains its own configuration, we can repurpose the
(unused in this case) tg3 link configuration members.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tg3 devices are shutdown, the driver uses the
TG3_PHYFLG_IS_LOW_POWER flag to enable a static phy configuration.
Any attempt to use the link configuration variables is dead code. This
patch removes such code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detecting the ASIC revision of a device is getting to be an increasingly
complex process. This patch consolidates all the ASIC rev detection
code to a single routine for better maintainability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver needs to submit a few phy register values to the UMP
firmware each time the link state changes. Up until now, the driver
would wait for the previous event to complete, then proceed to gather
data through a series of phy accesses. Since phy accesses are
relatively slow, it is possible for another thread to attempt to submit
its own event while the UMP code is still construction its message.
This patch seeks to minimize the collision window as much as possible by
preloading the phy data.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On newer devices, the hardware expects the NVRAM address register
to be written only once per NVRAM page. To do otherwise causes NVRAM
corruption. This patch fixes the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking the autoneg advertisements, the driver failed to include
the master and master enable bits for the bcm5701. This patch fixes the
problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the tg3 interface is down, the driver will return ethtool stats
uninitialized. This patch zeroes out the destination stat buffer in
such a case.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bug was found in the new DMA engine for the 57766. This patch
disables it, which causes the device to fallback to the old DMA engine.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves a comment in the transmit path to a better location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch eliminates the unneeded tg3_halt_cpu() prototype and moves
the tg3_setup_phy() prototype closer to where it is needed.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch relocates tg3_find_peer to eliminate a prototype.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the tg3_nvram_write_block functions higher in the file
to eliminate a prototype.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves __tg3_set_rx_mode above its first use and moves
tg3_set_rx_mode down closer to where the netdev_ops functions should be.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves tg3_change_mtu to a better location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves tg3_reset_task further down in the file where it makes
more sense to be.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch relocates tg3_restart_hw() to a better location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_start_xmit() makes the wrong assumption for TSOV6 that skb->head
doesnt include any payload data.
if (skb_is_gso_v6(skb))
hdr_len = skb_headlen(skb) - ETH_HLEN;
This is not true anymore after commit f07d960df3 (tcp: avoid frag
allocation for small frames)
We should instead use : skb_transport_offset(skb) + tcp_hdrlen(skb)
Its also true for IPv4
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled. However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup. When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.
This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt. In such a configuration, the
device's multivector interrupt mode must be disabled.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ethtool callbacks necessary to change the rss
indirection table from userspace. Should the number of interrupts
change (e.g. across a close / open call, or through a reset) and
any one of the indirection table values fall out-of-range, the driver
will reset the indirection table to a default layout.
[Integrated many suggestions made by Ben Hutchings.]
Changes since v3
* Removed TG3_FLAG_SUPPORT_MSIX checks at the start of
tg3_get_rxfh_indir() and tg3_set_rxfh_indir().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a new device member to hold the RSS indirection table
and separates out the code that initializes the table from the code that
programs the table into device registers.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces tg3's internal tg3_advert_flowctrl_1000T function
with mii_advertise_flowctrl provided by the kernel headers.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 57766 ASIC revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57766 ASIC rev will impose a new TX BD DMA limit on the driver.
This patch prepares for 57766 support by making the tx BD DMA limit
tunable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some devices in the 57765 ASIC rev that are EEE capable.
Unfortunately the EEE setup code only gets executed if the device is
gigabit capable. This patch fixes the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.122.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to return the flow control configuration
rather than the flow control status through the ETHTOOL_GPAUSEPARAM
ioctl.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to track the autonegotiation advertisements of the
link partner and report them through ethtool.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch integrates tg3_adv_1000T_flowctrl_ok() into
tg3_copper_is_advertising_all() and renames the function
tg3_phy_copper_an_config_ok().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tg3 has a place to store stats, but doesn't really use it. This patch
modifies the driver so that stats are saved across chip resets and gets
cleared across close / open calls.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the ethtool stats member from the tg3 device
structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to tg3 to use byte queue limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tg3 normally gets a performance boost by increasing the PCI Maximum Read
Request Size (MRRS) to 4k. Unfortunately, this is causing some problems
on particular hardware platforms. This patch removes all code that
modifies the MRRS except for one case.
As part of a solution to fix an internal FIFO problem on the 5719, the
driver artificially capped the MRRS to 2k for the entire 5719, and later
5720, ASIC revs. This was overly aggressive and only really needed to
be done for the 5719 A0. In the spirit of the rest of this patch, the
driver will only reprogram the MRRS for this device if the value exceeds
the 2k cap.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the earliest TSO capable devices, TSO was accomplished through
firmware. The TSO cannot coexist with ASF management firmware though.
The tg3 driver determines whether or not ASF is enabled by calling
tg3_get_eeprom_hw_cfg(), which checks a particular bit of NIC memory.
Commit dabc5c670d, entitled "tg3: Move
TSO_CAPABLE assignment", accidentally moved the code that determines
TSO capabilities earlier than the call to tg3_get_eeprom_hw_cfg(). As a
consequence, the driver was attempting to determine TSO capabilities
before it had all the data it needed to make the decision.
This patch fixes the problem by revisiting and reevaluating the decision
after tg3_get_eeprom_hw_cfg() is called.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future devices may or may not be capable of supporting larger rx
producer rings. This patch changes the code so that this flag is set on
an ASIC rev to ASIC rev basis. Also, this patch changes a place where
the LRG_PROD_RING_CAP flag was not controlling how the rx standard
producer ring size was set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BD replenish thresholds for the 57765 and newer ASIC revs are a
little strict. They were tuned for a mode that is currently unused.
This patch relaxes the thresholds so that they are set to values more
inline with the resources available.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
