The attached patch rate limits "WEP decrypt failed (ICV)" to avoid
flooding the logfiles.
Signed-off-by: Adel Gadllah <adel.gadllah@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression I (most likely) introduced, namely that
unencrypted frames are right now accepted even if we have a key for that
specific sender. That has very bad security implications.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes:
- Incorrect calls to ieee80211_hw_config when the radiotap flag is set.
- Failure to actually unset the radiotap flag when all monitors are down.
- Failure to call ieee80211_hw_config after successful interface start.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm not sure if this is best choice, someone might have better
solutions. But this patch fixed the connection problem when switching
from a WPA enabled AP (using wpa_supplicant) to an open AP (using
iwconfig). The root cause is when we connect to a WPA enabled AP,
wpa_supplicant sets the ifsta->extra_ie thru SIOCSIWGENIE. But if we
stop wpa_supplicant and connect to an open AP with iwconfig, there is
no way to clear the extra_ie so that mac80211 keeps connecting with that.
Someone could argue wpa_supplicant should clear the extra_ie during
its shutdown. But mac80211 should also handle the unexpected shutdown
case (ie. killall -9 wpa_supplicant).
On Wed, 2007-11-21 at 16:19 +0100, Johannes Berg wrote:
> Yeah. Can you amend the patch to also clear the
> IEEE80211_STA_PRIVACY_INVOKED flag?
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface with promisc/allmulti bit is taken down,
the mac80211 state can become confused. This fixes it by
making mac80211 keep track of all *active* interfaces that
have the promisc/allmulti bit set in the sdata, we sync
the interface bit into sdata at set_multicast_list() time
so this works.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I recently experienced unexplainable behaviour with the b43
driver when I had broken firmware uploaded. The cause may have
been that promisc mode was not correctly enabled or disabled
and this bug may have been the cause.
Note how the values are compared later in the function so
just doing the & will result in the wrong thing being
compared and the test being false almost always.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes scanning for specific ssid's which is broken due to the
scan being queued up without respecting the ssid to scan for.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I meant for this to be selectable only with EMBEDDED, not enabled only
with EMBEDDED. This does it that way. Sorry.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make "decrypt failed" and "have no key" debugging messages compile
conditionally upon CONFIG_MAC80211_DEBUG. They have been useful for
finding certain problems in the past, but in many cases they just
clutter a user's logs.
A typical example is an enviornment where multiple SSIDs are using a
single BSSID but with different protection schemes or different keys
for each SSID. In such an environment these messages are just noise.
Let's just leave them for those interested enough to turn-on debugging.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the long bug-hunt for why dynamic WEP networks didn't work it
turned out that mac80211 incorrectly uses IW_AUTH_KEY_MGMT while
it should use IW_AUTH_PRIVACY_INVOKED to determine whether to
associate to protected networks or not.
This patch changes the behaviour to be that way and clarifies the
existing code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver operations set_ieee8021x(), set_port_auth() and
set_privacy_invoked() are not used by any drivers, except
set_privacy_invoked() they aren't even used by mac80211.
Remove them at least until we need to support drivers with
mac80211 that require getting this information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Robert pointed out that I missed this file when removing the management
interface. Do it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows a driver to ask for a specific rate control algorithm.
The rate control algorithm asked for must be registered and be
available as a module or built-in.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, mac80211 would allow registering the same rate control
algorithm twice. This is a programming error in the registration
and should not happen; additionally the second version could never
be selected. Disallow this and warn about it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Too frequently people do not have module autoloading enabled
or fail to install the rate control module correctly, hence
their hardware probing fails due to no rate control algorithm
being available. This makes the 'simple' algorithm built into
the mac80211 module unless EMBEDDED is enabled in which case
it can be disabled (eg. if the wanted driver requires another
rate control algorithm.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
My AID message patch introduced a warning on 64-bit machines because ~
extends to unsigned long:
| net/mac80211/ieee80211_sta.c: In function ‘ieee80211_rx_mgmt_assoc_resp’:
| net/mac80211/ieee80211_sta.c:1187: warning: format ‘%d’ expects type ‘int’, but argument 7 has type ‘long unsigned int’
This fixes it by explicitly casting the result to u16 (which 'aid' is).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of the SSID desired should also be compared in addition to
the memcmp of the SSIDs.
Thanks to Andrea Merello <andreamrl@tiscali.it> for finding this issue.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commits
58b053e4ce ("Update arch/ to use sg helpers")
45711f1af6 ("[SG] Update drivers to use sg helpers")
fa05f1286b ("Update net/ to use sg helpers")
converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included. This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.
On most of the others this probably broke.
Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: Fix possible dev_deactivate race condition
[INET]: Justification for local port range robustness.
[PACKET]: Kill unused pg_vec_endpage() function
[NET]: QoS/Sched as menuconfig
[NET]: Fix bug in sk_filter race cures.
[PATCH] mac80211: make ieee802_11_parse_elems return void
define global BIT macro
move all local BIT defines to the new globally define macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some APs send management frames with junk padding after the last IE.
We already account for a similar problem with some Apple Airport
devices, but at least one device is known to send more than a single
extra byte. The device in question is the Draytek Vigor2900:
http://www.draytek.com.au/products/Vigor2900.php
The junk in question looks like an IE that runs off the end of the
frame. This cause us to return ParseFailed. Since the frame in
question is an association response, this causes us to fail to associate
with this AP.
The return code from ieee802_11_parse_elems is superfluous.
All callers still check for the presence of the specific IEs that
interest them anyway. So, remove the return code so the parse never
"fails".
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous IW_SCAN_THIS_ESSID patch left a hole allowing scan
requests on interfaces in inappropriate modes.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem of associating with wpa_secured hidden
AP. Please try out.
The original author of this patch is Bill Moss <bmoss@clemson.edu>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some AP equipment "in the wild" services multiple SSIDs using the
same BSSID. This patch changes the key of sta_bss_list to include
the SSID as well as the BSSID and the channel so as to prevent one
SSID from eclipsing another SSID with the same BSSID.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some AP equipment "in the wild" uses the same BSSID on multiple channels
(particularly "a" vs. "b/g"). This patch changes the key of sta_bss_list
to include both the BSSID and the channel so as to prevent a BSSID on
one channel from eclipsing the same BSSID on another channel.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no reason to warn about an invalid AID field when the
association was denied.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adam Baker reported that the prism2 ioctl removal changed behaviour
in that now the selection order was the other way around as before.
New API is planned but not done yet, so for now just use the first
matching channel in any mode as was previous behaviour with an unset
next_mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The decryption handlers will skip the frame if the RX_FLAG_DECRYPTED
flag is set, so the early flag setting introduced by Johannes breaks
decryption. To work around this, call the handlers first and then set
the flag.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Problem description by Daniel Drake <dsd@gentoo.org>:
"This sequence of events causes loss of connectivity:
<plug in>
<associate as normal in managed mode>
ifconfig eth7 down
iwconfig eth7 mode monitor
ifconfig eth7 up
ifconfig eth7 down
iwconfig eth7 mode managed
<associate as normal>
At this point you are associated but TX does not work. This is because
the eth7 hard_start_xmit is still ieee80211_monitor_start_xmit."
The problem is caused by ieee80211_if_set_type checking for a non-zero
hard_start_xmit pointer value in order to avoid changing that value for
master devices. The fix is to make that check more explicitly linked to
master devices rather than simply checking if the value has been
previously set.
CC: Daniel Drake <dsd@gentoo.org>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds sta_notify callback and removes sta_table_notification
which was not used by any driver.
sta_notify() is essential for drivers that keeps notion of station
internally and need to be notified about removal or addition of a station
to the (I)BSS or assocation to an AP.
This version adds interface id to the parameter list
as suggested by Johannes Berg
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the cfg80211 change_interface hook that changes the
type of an interface and cleans up the code a bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many devices have LEDs to indicate the link status.
Export this functionality to drivers.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves radiotap injection by removing the shortcut over TX handlers
that led to BUGS when injecting frames without setting a rate and also
resulted in various other quirks. Now, TX handlers are run but some
information that was present in the radiotap header is used instead of
automatic settings.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Andy Green <andy@warmcat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This "algorithm" is used only internally and is not useful.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes mac80211 set the RX_FLAG_DECRYPTED flag for frames
decrypted in software allowing us to handle some things more
uniformly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we have three RX handlers doing the decryption.
This patch changes it to have only one handler doing
everything, thereby getting rid of many duplicate checks.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
--
net/mac80211/rx.c | 46 ++++++++++++----------------------------------
1 files changed, 12 insertions(+), 34 deletions(-)
This moves the sta_process RX handler to after decryption
so that frames that cannot be decrypted don't influence
statistics, it is likely that they were injected or something
else is totally wrong.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes the management interface since it is only required
for hostapd/userspace MLME, will not be in the final tree
at least in this form and hostapd/userspace MLME currently
do not work against this tree anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since I cannot convince the lazy driver authors (hello Michael)
to stop (ab)using the MGMT interface type internally in their
drivers, this patch introduces a new _INVALID type especially
for their use and changes all affected drivers to use it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove the check for ops->config!=NULL, as it can never be NULL.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use bitwise NOT.
This also cleans up the code a little bit to make it more readable.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not useful since we do not support probe response
offload to hardware at this time and beacons are set in
another way.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes all prism2 ioctls.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we update the counters iff_promiscs and iff_allmultis
in struct ieee80211_local we have no common lock held to
protect them. The problem is that the update to each counter
may not be atomic, so we could end up with iff_promiscs == -1
in unfortunate conditions. To fix it, use atomic_t values.
It doesn't matter whether the two counters are updated
together atomically or not, if there are two invocations
of set_multicast_list we will end up with multiple
configure_filter() invocations of which the latter will always
be correct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>