Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Zeus console port is wired to a 8250-compatible device (pxa UARTs are
reserved to other uses). This patch allows such a configuration in the
uncompress sequence.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The original patch came from Marc Zyngier where support of 8250-compatible
UART is required to show the uncompress information. Modified a little bit
here, including changes below:
1. #include <mach/regs-uart.h> is actually not necessary
2. introduced uart_{read,write}() for different base and shift
3. introduced uart_is_enabled() and assumed enabled always for
non-PXA uarts
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
The irq_chip is not yet registered, so no default irq_chip.mask_ack(),
which we have to handle it correctly manually here.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since PMIC INT pin is a special pin of CPU, the status of PMIC INT pin needs
to be cleared after PMIC IRQ occured. Now append the clear operation in
irq chip handler.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Marvell MMP2 (aka ARMADA610) is a SoC based on PJ4 core. It's
ARMv6 compatible. Support basic interrupt handler and timer,
and basic support for MMP2 based FLINT platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Also remove a trailing whitespace while being there.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add some safety check for CONFIG_PM around zeus_power_off(). Without
it linking can fail like this:
arch/arm/mach-pxa/built-in.o: In function `zeus_power_off':
e800.c:(.text+0x2bc8): undefined reference to `pxa27x_cpu_suspend'
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This function gets only called from scoop_suspend() and scoop_resume() which are
only built in if we have CONFIG_PM set. Make it the same for check_scoop_reg().
This fixes the following warning:
arch/arm/common/scoop.c:143: warning: ‘check_scoop_reg’ defined but not used
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well
as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*.
IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as
IRQ_LOCOMO_KEY.
IRQ_LOCOMO_GPIO and the demultiplex handler should really be living
somewhere else.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Missing AC97 pin configurations are added where pxa_set_ac97_info() are
called for all pxa25x/pxa27x platforms. Where no exact configuration is
provided, use the default as in sound/arm/pxa2xx-ac97-lib.c
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is really pxa27x specific and should be kept in pxa27x.c. With this
newly introduced function, the original set_resetgpio_mode() is deprecated.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* Modification of Kconfig to add the Option
* 1 new file : buffalo-wxl-setup.c
This file is inspired from the db-78xx0-setup.c already present.
The following is done:
- Configure MPP Lines for the plateform (see my patch for MPP)
This is taken from the stock kernel provided by buffalotech (the vendor)
- GigaBit Ethernet
- Sata
- Uart are initiallized in a different way than on the dev board as we
have one core only.
- USB
The kernel has been running for some days now on my plateform.
Signed-off-by: Sebastien Requiem <sebastien@kolios.dk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch is composed of two new files :
- mpp.c which is mainly inspired by the same file as in mach-kirkwood
- mpp.h that is written from the documentation provided by Marvell
http://www.marvell.com/products/processors/embedded/discovery_innovation/HW_MV78100_OpenSource.pdf
Moreover, due to some implementation problem, I have
defined some MPPX_UNUSED that offer developers the possibility
to SET MPP to some unused value (such as for Buffalo WXL).
Note: This patch doesn't support MV78200 yet (only 78100 MPP lines have
been written)
Signed-off-by: Sebastien Requiem <sebastien@kolios.dk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Enable the kirkwood SATA SoC interface on the eSATA SheevaPlug.
Signed-off-by: John Holland <john.holland@cellent-fs.de>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
--
Allow basic eSATA SheevaPlug board configuration and build.
Signed-off-by: John Holland <john.holland@cellent-fs.de>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
--
This patch fix the below build error for arm1026ej-s processor (IntegratorCP/arm1026ej-s board).
CC init/main.o
In file included from include/linux/highmem.h:8,
from include/linux/pagemap.h:10,
from include/linux/mempolicy.h:62,
from init/main.c:52:
arch/arm/include/asm/cacheflush.h:134:2: error: #error Unknown cache maintainence model
make[1]: *** [init/main.o] Erreur 1
make: *** [init] Erreur 2
Signed-off-by: Abdoulaye Walsimou Gaye <walsimou@walsimou.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It appears the wrong GPIO registers were used
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
The 'outer_cache' variable is needed by the outer_inv_range(),
outer_clean_range() and outer_flush_range() functions, which are
declared as inline in asm/cacheflush.h. Otherwise drivers built
as a loadable module, which access these functions, will have
an undefined symbol.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: fix "acpi=ht" boot option
ACPI, i915: blacklist Clevo M5x0N bad_lid state
ACPI: fix High cpu temperature with 2.6.32
ACPI: dock: properly initialize local struct dock_station in dock_add()
ACPI: remove Asus P2B-DS from acpi=ht blacklist
thinkpad-acpi: wrong thermal attribute_group removed in thermal_exit()
ACPI: acpi_bus_{scan,bus,add}: return -ENODEV if no device was found
ACPI: Add NULL pointer check in acpi_bus_start
ACPI: processor: only evaluate _PDC once per processor
ACPI: processor: add kernel command line support for early _PDC eval
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/85xx: Fix SMP when "cpu-release-addr" is in lowmem
powerpc/85xx: Fix oops during MSI driver probe on MPC85xxMDS boards
We broke "acpi=ht" in 2.6.32 by disabling MADT parsing
for acpi=disabled. e5b8fc6ac1
This also broke systems which invoked acpi=ht via DMI blacklist.
acpi=ht is a really ugly hack,
but restore it for those that still use it.
http://bugzilla.kernel.org/show_bug.cgi?id=14886
Signed-off-by: Len Brown <len.brown@intel.com>
