I have no evidence for this byte being used this way, and lots of
counterexamples. Restore the struct to its empirical definition and
patch up gmbus setup to match.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
If the panel is powered up, there's no need to delay for the 'off'
interval when turning the panel on.
Signed-off-by: Keith Packard <keithp@keithp.com>
This eliminates a fairly long delay when power sequencing newer
hardware
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no good reason to turn off the eDP force VDD bit synchronously
while probing devices; that just sticks a huge delay into all mode
setting paths. Instead, queue a delayed work proc to disable the VDD
force bit and then remember when that fires to ensure that the
appropriate delay is respected before trying to turn it back on.
Signed-off-by: Keith Packard <keithp@keithp.com>
We need to check eDP VDD force and panel on in several places, so
create some simple helper functions to avoid duplicating code.
Signed-off-by: Keith Packard <keithp@keithp.com>
The return value was unused, so just stop doing that.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This value doesn't come directly from the VBT, and so is rather
specific to the particular DP output.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Store the panel power sequencing delays in the dp private structure,
rather than the global device structure. Who knows, maybe we'll get
more than one eDP device in the future.
From the eDP spec, we need the following numbers:
T1 + T3 Power on to Aux Channel operation (panel_power_up_delay)
This marks how long it takes the panel to boot up and
get ready to receive aux channel communications.
T8 Video signal to backlight on (backlight_on_delay)
Once a valid video signal is being sent to the device,
it can take a while before the panel is actuall
showing useful data. This delay allows the panel
to get something reasonable up before the backlight
is turned on.
T9 Backlight off to video off (backlight_off_delay)
Turning the backlight off can take a moment, so
this delay makes sure there is still valid video
data on the screen.
T10 Video off to power off (panel_power_down_delay)
Presumably this delay allows the panel to perform
an orderly shutdown of the display.
T11 + T12 Power off to power on (panel_power_cycle_delay)
So, once you turn the panel off, you have to wait a
while before you can turn it back on. This delay is
usually the longest in the entire sequence.
Neither the VBIOS source code nor the hardware documentation has a
clear mapping between the delay values they provide and those required
by the eDP spec. The VBIOS code actually uses two different labels for
the delay values in the five words of the relevant VBT table.
**** MORE LATER ***
Look at both the current hardware register settings and the VBT
specified panel power sequencing timings. Use the maximum of the two
delays, to make sure things work reliably. If there is no VBT data,
then those values will be initialized to zero, so we'll just use the
values as programmed in the hardware. Note that the BIOS just fetches
delays from the VBT table to place in the hardware registers, so we
should get the same values from both places, except for rounding.
VBT doesn't provide any values for T1 or T2, so we'll always just use
the hardware value for that.
The panel power up delay is thus T1 + T2 + T3, which should be
sufficient in all cases.
The panel power down delay is T1 + T2 + T12, using T1+T2 as a proxy
for T11, which isn't available anywhere.
For the backlight delays, the eDP spec says T6 + T8 is the delay from the
end of link training to backlight on and T9 is the delay from
backlight off until video off. The hardware provides a 'backlight on'
delay, which I'm taking to be T6 + T8 while the VBT provides something
called 'T7', which I'm assuming is s
On the macbook air I'm testing with, this yields a power-up delay of
over 200ms and a power-down delay of over 600ms. It all works now, but
we're frobbing these power controls several times during mode setting,
making the whole process take an awfully long time.
Signed-off-by: Keith Packard <keithp@keithp.com>
Any call to intel_dp_sink_dpms must ensure that the panel has power so
that the DP_SET_POWER operation will be correctly received. The only
one missing this was in intel_dp_prepare.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DP i2c initialization code does a couple of i2c transactions,
which means that an eDP panel must be powered up.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Talking to the eDP DDC channel requires that the panel be powered
up. Wrap both the EDID and modes fetch code with calls to turn the vdd
power on and back off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On eDP, DDC requires panel power, but turning that on uses the panel
power sequencing timing values fetch from the DPCD data.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the panel is already off, we'll need to turn VDD on to execute the
(useless) DPMS off code. Yes, it would be better to just not do any of
this, but correctness, and *then* performance.
Signed-off-by: Keith Packard <keithp@keithp.com>
The VDD force bit is turned on before touching the panel, but if it
was enabled, there was no call to turn it back off. Add a call.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid any question about locked registers by just writing the unlock
pattern with every write to the register.
Signed-off-by: Keith Packard <keithp@keithp.com>
Verify that the eDP VDD is on, either with the panel being on or with
the VDD force-on bit being set.
This demonstrates that in many instances, VDD is not on when needed,
which leads to failed EDID communications.
Signed-off-by: Keith Packard <keithp@keithp.com>
We're going to assume that EDID is more reliable than the VBT tables
for eDP panels, which is notably true on MacBook machines where the
VBT contains completely bogus data.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This masks out all interrupts and ack's any pending ones at IRQ
uninstall time to make sure we don't receive any unexpected interrupts
later on.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were relying on the BIOS to set these bits, which doesn't always
happen.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The reference clock configuration must be done before any mode setting
can occur as all outputs must be disabled to change
anything. Initialize the clocks after turning everything off during
the initialization process.
Also, re-initialize the refclk at resume time.
Signed-off-by: Keith Packard <keithp@keithp.com>
I can't find any reference clocks which run at 96MHz as seems to be
indicated from the comments in this code.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
When trying to use SSC on Ibex Peak without CK505, any non-SSC outputs
(like VGA or TV) get broken. So, do not use SSC on Ibex Peak unless
there is a CK505 available (as specified by the VBT).
On Cougar Point, all clocking is internal, so SSC can always be used,
and there will never be a CK505 available.
This eliminates VGA shimmer on some Ironlake machines which have a
CK505 clock source.
References: https://bugzilla.kernel.org/show_bug.cgi?id=21742
References: https://bugs.freedesktop.org/show_bug.cgi?id=38750
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The PCH refclk settings are global, so we need to look at all of the
encoders, not just the current encoder when deciding how to configure
it. Also, handle systems with more than one panel (any combination of
PCH/non-PCH eDP and LVDS).
Disable SSC clocks when no panels are connected.
Signed-off-by: Keith Packard <keithp@keithp.com>
Allow SSC to be enabled even when the BIOS disables it for testing SSC paths.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
This includes whether an eDP panel is present, and whether that should
use SSC (and at what frequency)
Signed-off-by: Keith Packard <keithp@keithp.com>
This tells the driver whether a CK505 clock source is available on
pre-PCH hardware. If so, it should be used as the non-SSC source,
leaving the internal clock for use as the SSC source.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wison <chris@chris-wilson.co.uk>
These are all KMS related anyways, so don't hide them under other
debug levels.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Make the default FBC behaviour chipset specific, allowing us to turn
it on by default for Ironlake and older where it has been seen to
cause trouble with screen updates.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Francis Moreau <francis.moro@gmail.com>
I was seeing a nasty 5 frame glitch every 10 seconds, caused by the
poll for connection on DVI attached by SDVO.
As my SDVO DVI supports hotplug detect interrupts, the fix is to
enable them, and hook them in to the various bits of driver
infrastructure so that they work reliably.
Note that this is only tested on single-function DVI-D SDVOs, on two
platforms (965GME and 945GSE), and has not been checked against a
specification document.
With lots of help from Adam Jackson <ajax@redhat.com> on IRC.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
While I think the previous code is correct, it was hard to follow and
hard to debug. Since we already have a ring abstraction, might as well
use it to handle the semaphore updates and compares.
I don't expect this code to make semaphores better or worse, but you
never know...
v2:
Remove magic per Keith's suggestions.
Ran Daniel's gem_ring_sync_loop test on this.
v3:
Ignored one of Keith's suggestions.
v4:
Removed some bloat per Daniel's recommendation.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add ELD support for Intel Eaglelake, IbexPeak/Ironlake,
SandyBridge/CougarPoint and IvyBridge/PantherPoint chips.
ELD (EDID-Like Data) describes to the HDMI/DP audio driver the audio
capabilities of the plugged monitor. It's built and passed to audio
driver in 2 steps:
(1) at get_modes time, parse EDID and save ELD to drm_connector.eld[]
(2) at mode_set time, write drm_connector.eld[] to the Transcoder's hw
ELD buffer and set the ELD_valid bit to inform HDMI/DP audio driver
This patch is tested OK on G45/HDMI, IbexPeak/HDMI and IvyBridge/HDMI+DP.
Test scheme: plug in the HDMI/DP monitor, and run
cat /proc/asound/card0/eld*
to check if the monitor name, HDMI/DP type, etc. show up correctly.
Minor imperfection: the GEN5_AUD_CNTL_ST/DIP_Port_Select field always
reads 0 (reserved). Without knowing the port number, I worked it around
by setting the ELD_valid bit for ALL the three ports. It's tested to not
be a problem, because the audio driver will find invalid ELD data and
hence rightfully abort, even when it sees the ELD_valid indicator.
Thanks to Zhenyu and Pierre-Louis for a lot of valuable help and testing.
CC: Zhao Yakui <yakui.zhao@intel.com>
CC: Wang Zhenyu <zhenyu.z.wang@intel.com>
CC: Jeremy Bush <contractfrombelow@gmail.com>
CC: Christopher White <c.white@pulseforce.com>
CC: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
CC: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We want to enable dithering on any pipe where the frame buffer has
more color resolution than the output device.
The previous code was incorrectly clamping the frame buffer bpc to the
display bpc, effectively disabling dithering all of the time as the
computed frame buffer bpc would never be larger than the display bpc.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
We want to enable dithering on any pipe where the frame buffer has
more color resolution than the output device.
The previous code was incorrectly clamping the frame buffer bpc to the
display bpc, effectively disabling dithering all of the time as the
computed frame buffer bpc would never be larger than the display bpc.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Otherwise it just contains random memory.
Issue detected by cppcheck.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The commit "Not all systems expose a firmware or platform mechanism for
changing the backlight intensity on i915, so add native driver support"
adds calls to intel_panel_setup_backlight() from intel_{lvds,dp}_init
so do not call it again from intel_setup_outputs().
BugLink: http://bugs.launchpad.net/bugs/831542
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
ACKed-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge
Prior to Ivybridge, the GFX_MODE would default to 0x800, meaning that
MI_FLUSH would flush the TLBs in addition to the rest of the caches
indicated in the MI_FLUSH command. However starting with Ivybridge, the
register defaults to 0x2800 out of reset, meaning that to invalidate the
TLB we need to use PIPE_CONTROL. Since we're not doing that yet, go
back to the old default so things work.
v2: don't forget to actually *clear* the new bit
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The clock gating functions are only assigned under KMS, so don't try
to call them under UMS.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Disable this feature when KMS is not running by setting the
driver->get_vblank_timestamp function pointer to NULL.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com>
Tested-by: Michel Alexandre Salim <salimma@fedoraproject.org>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
We ought to be calling this from our DPMS routines as well as global
state may change and we need to enable/disable clocks. So split out the
code in preparation for further changes.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
IVB uses the same interrupt reg layout as SNB, so add an IS_GEN7 to the
interrupt debugfs file.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Just an extra parameter which isn't actually needed.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CPT pipe select is different from previous generations (using two bits
instead of one). All of the paths from intel_disable_pch_ports were
not making this distinction.
Mode setting with pipe A turned off would then also force all outputs
on pipe B to get turned off as the disable code would mistakenly
decide that all of these outputs were on pipe A and turn them off.
This is an extension of the CPT DP disable fix (why didn't I fix this then?)
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There's no reason to relock them; it just makes operations more
complex. This fixes DPMS where the panel registers were locked making
the disable not work.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During mode setting, check to make sure the panel power sequencing has
completed before doing further operations on the device. This
uncovered errors with DPMS not turning the device off as it was left locked.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Expose the SNB+ cache sharing policy register in debugfs. The new file,
i915_cache_sharing, has 4 values, 0-3, with 0 being "max uncore
resources" and 3 being the minimum. Exposing this control should make
benchmarking easier and help us choose a good default.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This makes it easier to add support for other infoframes (e.g. SPD,
vendor specific).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes and I found a couple of issues where incorrect mode
setting would cause problems with RC6 enabled. We're hopeful that
fixing those will resolve the outstanding issues with a few machines
that had trouble before 3.0 with rc6.
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Francesco Allertsen <fallertsen@gmail.com>
Cc: Ted Phelps <phelps@gnusto.com>
Cc: Gu Rui <chaos.proton@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38567
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38332
Signed-off-by: Keith Packard <keithp@keithp.com>
This reverts commit 97cdd71010.
Clearing the dpcd data means that if the fetch fails, any previous
data will be lost. On eDP, this is no fun as we only fetch dpcd at
init time, so the memset will destroy that the next time through.
Before initiating a new read or write on the DP AUX channel, wait for
any outstanding activity to complete. This may happen during normal
retry behavior. If the wait fails (i.e. after 1ms the AUX channel is
still busy) dump a backtrace to make the caller easier to spot.
v2: use msleep instead, and timeout after 3ms (only ever saw 1 retry
with msleep in testing)
v3: fix backtrace check to trigger if the 3ms wait times out
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=38136.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The EDID parser will zero out the bpc value, and the driver needs to handle
that case. In our picker, we'll just ignore 0 values as far as bpp
picking goes.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=39323.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
At least on a Lenovo X220 the HPD bits of this are enabled at boot but
cleared after resume, which means plug interrupts stop working.
This also happens to fix DP displays re-lighting on resume. I'm quite
certain that's an accident: the first DP link train inevitably fails on
that machine, and it's only serendipity that we're getting multiple plug
interrupts and the second train works. But I shall take my victories
where I get them.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
These bits moved around on SNB and above.
v2: again with the git send-email fail
v3: add macros for getting per-pipe override & enable bits
v4: enable phase sync pointer on SNB and IVB configs as well
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Using the new quirk added to support disabling SSC on Lenovo U160
(#36656, commit 435793dfb8), also register
the Vaio as a special case and disable SSC for it.
This patch fixes#34437 on fdo bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=34437
Signed-off-by: Michel Alexandre Salim <salimma@fedoraproject.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
If a mode set fails we may get a message from drm_crtc_helper if we're lucky,
but it won't tell us anything about *why* we failed to set a mode. So
add a few DRM_ERRORs for the cases that shouldn't happen so we can debug
things more easily.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Mainly for use in debugging and benchmarking, this file allows the user
to control the max frequency used by the GPU. Frequency may still vary
based on workload (if the frequency is set to higher than the minimum)
but won't go over the newly set value.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The Dell OptiPlex FX170 claims to have LVDS, but doesn't.
Signed-off-by: Pieterjan Camerlynck <pieterjan.camerlynck@gmail.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Failing to pin a scanout buffer will most likely lead to a black
screen, so if the GPU is wedged, then just let the pin happen and hope
that things work out OK.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
On Ironlake and above, we have per-transcoder DIP registers, so use them
for sending DIPs like AVI infoframes on ILK and above.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
CB tuning is needed to handle potential process variations that might
cause clock jitter for certain PLL settings. However, we were setting
it incorrectly since we were using the wrong M value as a check (M1 when
we needed to use the whole M value). Fix it up, making my HDMI
attached display a little prettier (used to have occasional dots crawl
across the display).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Writes to the plane control register are buffered in the chip until a
write to the DSPADDR (pre-965) or DSPSURF (post-965) register occurs.
This patch adds flushes in:
intel_enable_plane
gen6_init_clock_gating
ivybridge_init_clock_gating
Signed-off-by: Keith Packard <keithp@keithp.com>
After writing to the plane control reg we need to write to the surface
reg to trigger the double buffered register latch. On previous
chipsets, writing to DSPADDR was enough, but on ILK+ DSPSURF is the reg
that triggers the double buffer latch.
v2: write DSPADDR too to cover pre-965 chipsets
v3: use flush_display_plane instead, that's what it's for
v4: send the right patch
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
On CougarPoint and PantherPoint PCH chips, the timing generator may fail
to start after DP training completes. This is due to a bug in the
FDI autotraining detect logic (which will stall the timing generator and
re-enable it once training completes), so disable it to avoid silent DP
mode setting failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This corrects the DPMS mode tracking so that the DPMS code will
actually turn the CRTC off the next time the screen saves.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 885a50147f.
We actually *do* need to track DPMS state so that on hotplug, we don't
retrain the link until DPMS is disabled.
However, that code had avery small bug -- it wouldn't set the
dpms_mode at mode set time, and so link retraining would not actually
occur on monitor hotplug until the monitor had gone through a DPMS
off/DPMS on cycle.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
Display port pipe selection on CPT is not done with a bit in the
output register, rather it is controlled by a couple of bits in the
separate transcoder register which indicate which display port output
is connected to the transcoder.
This patch replaces the simplistic macro DP_PIPE_ENABLED with the
rather more complicated function dp_pipe_enabled which checks the
output register to see if that is enabled, and then goes on to either
check the output register pipe selection bit (on non-CPT) or the
transcoder DP selection bits (on CPT).
Before this patch, any time the mode of pipe A was changed, any
display port outputs on pipe B would get disabled as
intel_disable_pch_ports would ensure that the mode setting operation
could occur on pipe A without interference from other outputs
connected to that pch port
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Eliminates an open-coded read and also gains the retry behaviour of
intel_dp_get_dpcd, which seems like a good idea.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
This describes the function better, allowing it to be used where the
DPCD value is relevant.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
This uses the common dpcd reading routine, i915_dp_detect_common,
instead of open-coding a call to intel_dp_aux_native_read. Besides
reducing duplicated code, this also gains the read retries which
may be necessary when a cable is first plugged back in and the link
needs to be retrained.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
drm_helper_hpd_irq_event queues another work proc to go and deliver
the user-space event, and that function also wants to hold the config
mutex, so we shouldn't hold the mutex across the
drm_helper_hpd_irq_event call.
Signed-off-by: Keith Packard <keithp@keithp.com>
The docs say the port has to come on in training pattern 1; at this
point, though, ->DP is in normal mode. The intent here is to wait
until the port is in fact sending data, but that doesn't happen since
we've broken the sequence the hardware expects, and the vblank wait will
time out and kvetch in the log.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The DP spec says training patterns 1 and 2 are to be sent non-scrambled,
and the GPU docs claim that happens (or at least, there's no explicit
scrambling control). But the sink may be confused if we don't
explicitly tell it what we're doing, so play it safe.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Consider a 1600x900 panel, upscaling a 1360x768 mode, full-aspect. The
old math would give you:
scaled_width = 1600 * 768; /* 1228800 */
scaled_height = 1360 * 900; /* 1224000 */
if (scaled_width > scaled_height) { /* pillarbox, and true */
width = 1224000 / 768; /* int(1593.75) = 1593 */
x = (1600 - 1593 + 1) / 2; /* 4 */
y = 0;
height = 768;
} /* ... */
This is broken. The total width of scanout would then be 1593 + 4 + 4,
or 1601, which is wider than the panel itself. The hardware very
dutifully implements this, and you end up with a black 45° diagonal from
the top-left corner to the bottom edge of the screen. It's a cool
effect and all, but not what you wanted. Similar things happen for the
letterbox case.
The problem is that you have an integer number of pixels, which means
it's usually impossible to upscale equally on both axes. 1360/768 is
1.7708, 1600/900 is 1.7777. Since we're constrained on the one axis,
the other one wants to come out as an even number of pixels (the panel
is almost certainly even on both axes, and the x/y offsets will be
applied on both sides). In the math above, if 'width' comes out even,
rounding down is correct; if it's odd, you'd rather round up. So just
increment width/height in those cases.
Tested on a Lenovo T500 (Ironlake).
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-By: Daniel Manrique <daniel.manrique@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38851
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Hotplug detection is a mode setting operation and must hold the
struct_mutex or risk colliding with other mode setting operations.
In particular, the display port hotplug function attempts to re-train
the link if the monitor is supposed to be running when plugged back
in. If that happens while mode setting is underway, the link will get
scrambled, leaving it in an inconsistent state.
This is a special case -- usually the driver mode setting entry points
are covered by the upper level DRM code, but in this case the function
is invoked as a work function not under the control of DRM.
Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It's not clear what a sink would do if you wrote zero to this register -
which I guess would mean "I don't support any channel encodings, good
luck" - but let's not find out.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
%hx alone prints 0 as "0", not "00".
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
For parity with radeon and nouveau, and also because I suspect we're
going to need it to get format-conversion dongles right.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
No reason not to see this on g4x, after all.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Physically-addressed hardware status pages are initialized early in
the driver load process by i915_init_phys_hws. For UMS environments,
the ring structure is not initialized until the X server starts. At
that point, the entire ring structure is re-initialized with all new
values. Any values set in the ring structure (including
ring->status_page.page_addr) will be lost when the ring is
re-initialized.
This patch moves the initialization of the status_page.page_addr value
to intel_render_ring_init_dri.
Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org
Failing to pin a scanout buffer will most likely lead to a black
screen, so if the GPU is wedged, then just let the pin happen and hope
that things work out OK.
v2: Just ignore any error from i915_gem_object_wait_rendering, as
suggested by Chris Wilson
Signed-off-by: Keith Packard <keithp@keithp.com>
