- Also refactor the conditional to use the existing tg3_pci_tbl array.
- Set flags in the driver_data field of the pci_device_id structure to
identify these devices.
- Add PCI_DEVICE_SUB() to pci.h to declare PCI 4-part IDs to match these
devices.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip ready check added by the commit 3ac3546e [Always wait for
the chip to be ready] does not work when the register read/write
is word swapped. This check has been added before the WORD_SWAP
register is programmed, so we need to check for swapped register
value as well.
Bit 16 is marked as RESERVED in SMSC datasheet, Steve Glendinning
<steve@shawell.net> checked with SMSC and wrote:
The chip architects have concluded we should be reading PMT_CTRL
until we see any of bits 0, 8, 16 or 24 set. Then we should read
BYTE_TEST to check the byte order is correct (as we already do).
The rationale behind this is that some of the chip variants have
word order swapping features too, so the READY bit could actually
be in any of the 4 possible locations. The architects have confirmed
that if any of these 4 positions is set the chip is ready. The other
3 locations will either never be set or can only go high after READY
does (so also indicate the device is ready).
This change will check for the READY bit at the 16th position. We do
not check the other two cases (bit 8 and 24) since the driver does not
support byte-swapped register read/write.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 175c0dff, drivers uses tasklet_kill to avoid put disabled tasklet
on the tasklet vec. But some of the drivers uses tasklet_init & tasklet_disable
in the driver init code, then tasklet_enable when it is opened. This makes
tasklet_enable on a killed tasklet and make ksoftirqd crazy then. Normally,
drivers should use tasklet_init/tasklet_kill on device open/remove, and use
tasklet_disable/tasklet_enable on device suspend/resume.
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first register set is used for matching but
we support getting the initial hw addr from any of
the registers.
To prevent stale entries and false matches clear unused
register sets. This most important for the at91_ether
driver where u-boot always uses the 2nd register set.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both these PHYs support interrupt generation on IC pin 32.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__IPTUNNEL_XMIT() is an ugly macro, convert it to a static
inline function, so make it more readable.
IPTUNNEL_XMIT() is unused, just remove it.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old ifdef CONFIG_BRCMFISCAN looks wrong to me and it makes more
sense when CONFIG_BRCMISCAN is used.
This patch was just compile tested by me, but not runtime tested.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the event of a VXLAN device being linked to a device that has a
hard_header_len greater than that of standard ethernet we could end up with
the hard_header_len not being large enough for outgoing frames. In order to
prevent this we should update the length when a lowerdev is provided.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eXtensible and not eXtensiable in the comment on top.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds static declaration to several functions in bnx2x. It eliminates
newly introduced sparse warnings reported by Fengguang Wu.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change fixes an issue I found where VXLAN frames were fragmented when
they were up to the VXLAN MTU size. I root caused the issue to the fact that
the headroom was 4 + 20 + 8 + 8. This math doesn't appear to be correct
because we are not inserting a VLAN header, but instead a 2nd Ethernet header.
As such the math for the overhead should be 20 + 8 + 8 + 14 to account for the
extra headers that are inserted for VXLAN.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of Huawei 3G and LTE modems implement a CDC NCM function,
including the necessary functional descriptors, but using a non
standard interface layout and class/subclass/protocol codes.
These devices can be handled by this driver with only a minor
change to the probing logic, allowing a single combined control
and data interface. This works because the devices
- include a CDC Union descriptor labelling the combined
interface as both master and slave, and
- have an alternate setting #1 for the bulk endpoints on the
combined interface.
The 3G/LTE network connection is managed by vendor specific AT
commands on a serial function in the same composite device.
Handling the managment function is out of the scope of this
driver. It will be handled by an appropriate USB serial
driver.
Reported-and-Tested-by: Olof Ermis <olof.ermis@gmail.com>
Reported-and-Tested-by: Tommy Cheng <tommy7765@yahoo.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device datasheet specifies the BUSY bit must be set when reading
or writing phy registers. This patch ensures we do that.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows users to enable and disable EEE using Ethtool.
It also allows users to get EEE settings, as supported by the device.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to both improve the performance and reduce the size of
igb_tx_map. To do this I have expanded the work done in the main loop by
pushing first into tx_buffer. This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor. The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to improve the efficiency of the Tx flags in igb by
aligning them with the values that will later be written into either the
cmd_type or olinfo. By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.
In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to reduce the overhead for workloads that are not
using either TSO or checksum offloads. Most of the time the compiler
should jump ahead after failing this check to the VLAN check since in the
igb_tx_csum call we start with that check as well.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides ability to enable or disable UDP RSS hashing. It gives
users option of generating RSS hash based on the UDP source and destination
ports numbers. Currently, UDP flow hash is always disabled in igb-driver.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Customers are requesting that the hw prevents PHY from establishing link
until the driver loads. This patch clears the Go Link Disconnect bit which
provides the requested behavior on parts 82580 and later.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to support up to 15k buffers since the HW is limited to
9.5k in SR-IOV mode. Instead, allocate buffers that fit and align inside
of a 32K memory buffer.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_gro_receive shouldn't be called from netpoll context. Doing
so was causing kernel panics when jumbo frames larger than 2K were set.
Add a flag to check if the Rx ring processing is occurring from interrupt
context or from netpoll context and call netif_rx() if in the polling
context.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves the following warning:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c: In function ‘ixgbevf_probe’:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1742:290: warning: ‘err’ may be used uninitialized in this function [-Wuninitialized]
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1717:6: note: ‘err’ was declared here
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver cannot work without MSI-X interrupts
so there is no mechanism to fall back to.
Signed-off-by: Jakub Kicinski <jakub.kicinski@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way the code was previously written it was causing DCA to prefetch the
entire packet into the cache when it was enabled. That is excessive as we
only really need the headers.
We are now prefetching the headers via software so doing this from DCA would
be redundant anyway. So clear the bit that was causing us to prefetch the
packet data and instead only use DCA for the descriptor rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since eab6d18d (vlan: Don't check for vlan group before
vlan_tx_tag_present.) we don't check tp->vlgrp and thus
tp is not needed in this function.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a gianfar ethernet device is down prior to hibernating a
system, it will no longer be present upon system restore.
For example:
~# ifconfig eth0 down
~# echo disk > /sys/power/state
<trigger a restore from hibernation>
~# ifconfig eth0 up
SIOCSIFFLAGS: No such device
This happens because the restore function bails out early upon
finding devices that were not up at hibernation. In doing so,
it never gets to the netif_device_attach call at the end of
the restore function. Adding the netif_device_attach as done
here also makes the gfar_restore code consistent with what is
done in the gfar_resume code.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should gfar_init_bds() return with -ENOMEM inside gfar_alloc_skb_resources(),
free_skb_resources() will be called twice in a row on the "cleanup" path,
leading to duplicate kfree() calls for rx_|tx_queue->rx_|tx_skbuff resulting
in segmentation fault.
This patch prevents the segmentation fault to happen in the future
(rx_|tx_sbkbuff set to NULL), and corrects the error path handling
for gfar_init_bds().
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These can be converted to net_*_ratelimited().
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when something goes wrong, a flood of these messages can be
generated by usbnet (thousands per second). This doesn't
generally *help* the condition so this patch ratelimits the
rate of their generation.
There's an underlying problem in usbnet's kevent deferral
mechanism which needs fixing, specifically that events *can*
get dropped and not handled. This patch doesn't address this,
but just mitigates fallout caused by the current implemention.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a phy_id sysfs attribute to MDIO devices, containing the
32-bit PHY identifier reported by the device. This attribute can
be useful when debugging problems related to phy drivers. Other
enumerable buses already have similar attributes.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the wanxl firmware array const so that it goes in the read-only section.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the wanxl firmware to include missing constants such as PARITY_NONE. It
should be #including the linux/hdlc/ioctl.h header.
To make this work, we also have to guard parts of ioctl.h with !__ASSEMBLY__.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wanxl firmware needs access to some bits of UAPI stuff, so the -I flag in
the Makefile needs adjusting to point at the UAPI headers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some people wants to log only oops messages via netconsole,
(this is also why netoops was invented)
so add a module option for netconsole. This can be tuned
via /sys/module/netconsole/parameters/oops_only at run time
as well.
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shmobile SH7377 already was removed from source tree.
This remove SH7377 support for sh-irda.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shmobile SH7367 already was removed from source tree.
This remove SH7367 support for sh-irda.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cdc_eem frames might need to contain 802.1Q VLAN Ethernet frames.
URB/skb sizing from usbnet will default to the hard_mtu,
so account for the VLAN header by expanding that via hard_header_len
Signed-off-by: Ian Coolidge <iancoolidge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
INGPADBOUNDARY_MASK is already shifted. No need to shift it again. On reloading
a driver it was resulting in a bad SGE FL MTU sizes [1536, 9088] error. This
only causes an issue on systems that have L1 cache size of 32B, 128B, 512B,
2048B or 4096B.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the BCM_CNIC define with a flag which can change at run-time
and which does not use the CONFIG_CNIC kconfig option.
For the PF/hypervisor driver cnic is always supported, however allocation of
cnic resources and configuration of the HW for offload mode is done only when
the cnic module registers bnx2x.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the driver-FW HSI to support changes to the 'update' ramrod
(FW supports this change since 7.8.2). This ramrod is sent when the cnic module
registers bnx2x, to enable changing the nic_mode configuration in HW at
run-time.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move below calculate out of spin lock section
diff = fep->cc.mult;
diff *= ppb;
diff = div_u64(diff, 1000000000ULL);
diff is local variable and not neccesary in spin lock
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PPS.
Limit FEC_PTP option for i.MX chip only.
FEC_PTP default is on at mx6 platform.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all printk's to netdev_ counterparts and fix up some
printed texts.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer used after gpio phy interrupt support was
removed from at91_ether.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is used on one AT91RM9200 board where a bootloader stores
the Ethernet address in the wrong order.
Support this on macb so address setting functions can be shared
with the at91_ether driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver in u-boot uses the first register set while
the at91_ether driver in u-boot uses the second register set.
By checking all register set, like at91_ether does, this code
can be shared between the drivers.
This only changes behavior on macb if no vaild address
is found in the first register set.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
roce interface is suppored only on Skyhawk-R.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SEMAPHORE register was being accessed from the csr BAR space. This BAR
may not be available in some Skyhawk-R configurations. Instead, access this
register via the PCI config space (it's available there too).
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) separate NIC and roce bar mapping code
2) parse sli_intf::if_type inside be_map_pci_bars() as if_type must be
used only to identify bars.
3) Use pci_iomap/unmap() routines
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SKYHAWK_FAMILY will not identify all revisions of the chip.
Use device-id check (skyhawk_chip() macro) instead.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->generation was being incorrectly set as BE_GEN3 for Skyhawk-R.
Replace generation usage with XXX_chip() macros to identify the chip.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not assume reserve fields to be don't cares as fields may change.
Clearing data structures before using.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 currently uses a too high tx coalescing setting, deferring
TX completion interrupts by up to 128 us.
With the recent skb_orphan() removal in commit 8112ec3b87,
performance of a single TCP flow is capped to ~4 Gbps, unless
we increase tcp_limit_output_bytes.
I suggest using 16 us instead of 128 us, allowing a finer control.
Performance of a single TCP flow is restored to previous levels,
while keeping TCP small queues fully enabled with default sysctl.
This patch is also a BQL prereq.
Reported-by: Vimalkumar <j.vimal@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets the runtime PM reference count before calling
usbnet_{read|write}_cmd, and puts it after completion of the
usbnet_{read|write}_cmd, so that the usb control message can always
be sent to one active device in the non-PM context.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch applies the introduced usbnet_read_cmd_nopm() and
usbnet_write_cmd_nopm() in the callback of resume and suspend
to avoid deadlock if USB runtime PM is considered into
usbnet_read_cmd() and usbnet_write_cmd().
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes memory leak in smsc95xx_suspend.
Also, it isn't necessary to bother mm to allocate 8bytes/16byte,
and we can use stack variable safely.
Acked-By: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch applies the introduced usbnet_read_cmd_nopm() and
usbnet_write_cmd_nopm() in the callback of resume and suspend
to avoid deadlock if USB runtime PM is considered into
usbnet_read_cmd() and usbnet_write_cmd().
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the below two helpers to prepare for solving
the usbnet runtime PM problem, which may cause some network utilities
(ifconfig, ethtool,...) touch a suspended device.
usbnet_read_cmd_nopm()
usbnet_write_cmd_nopm()
The above two helpers should be called by usbnet resume/suspend
callback to avoid deadlock.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On gcc 4.7, we will get alignment traps in the ip stack if we don't align
the ip headers on receive. The h/w can support this, so use ip aligned
allocations.
Cut down the unnecessary padding on the allocation. The buffer can start on
any byte alignment, but the size including the begining offset must be 8
byte aligned. So the h/w buffer size must include the NET_IP_ALIGN offset.
Thanks to Eric Dumazet for the initial patch highlighting the padding issues.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only generate tx interrupts on every ring size / 4 descriptors. Move the
netif_stop_queue call to the end of the xmit function rather than
checking at the beginning.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupts have already been cleared, so we don't need to clear them
again. Also, we could miss interrupts if they are cleared, but we don't
process the packet.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard readl/writel accessors involve a spinlock and cache sync
operation on ARM platforms with an outer cache. Only DMA triggering
accesses need this, so use the raw variants instead in the critical paths.
The relaxed variants would be more appropriate, but don't exist on all
arches.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New received frames will trigger the rx DMA to poll the DMA descriptors,
so there is no need to tell the h/w to poll. We also want to enable
dropping frames from the fifo when there is no buffer.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the tx dma to start reading the next frame while sending the current
frame.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To let mac80211 clean up any TX information when
a frame is dropped, use ieee80211_free_txskb().
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
instead of making separate tg3_napi_disable() and netif_tx_disable() calls.
Update version to 3.126.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 5717C0 which is a 5720A0 with special bonds-out option.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed some coding style issues.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl throws error message for the current code. This patch fixes
this coding style issue.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Jitendra Kalsaria <Jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX replenish code doesn't handle DMA mapping failures,
which will cause issues if there actually is a failure. This
was reported by Shuah Khan who found a DMA mapping framework
warning ("device driver failed to check map error").
Cc: stable@vger.kernel.org
Reported-by: Shuah Khan <shuah.khan@hp.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The following chips need to enable internal settings to let ASPM
and clock request work.
RTL8111E-VL, RTL8111F, RTL8411, RTL8111G
RTL8105, RTL8402, RTL8106
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use WARN rather than printk followed by WARN_ON(1), for conciseness.
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression list es;
@@
-printk(
+WARN(1,
es);
-WARN_ON(1);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building atp.o triggers this GCC warning:
drivers/net/ethernet/realtek/atp.c: In function ‘set_rx_mode’:
drivers/net/ethernet/realtek/atp.c:871:26: warning: ‘mc_filter[0]’ may be used uninitialized in this function [-Wuninitialized]
GCC is correct. In promiscuous mode 'mc_filter' will be used
uninitialized in set_rx_mode_8012(), which is apparently inlined into
set_rx_mode().
But it turns out set_rx_mode_8012() will never be called, since
net_local.chip_type will always be RTL8002. So we can just remove
set_rx_mode_8012() and do some related cleanups.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW driver remaps two different IO regions, but fails to unmap them
both. This patch fixes the issue by calling iounmap in the appropriate
places.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When underlying phy driver restores its state very fast after being brought
down and up so that macb driver function macb_handle_link_change() was never
called with link state "down", driver's internal representation of phy speed
and duplex (bp->speed and bp->duplex) didn't change. So, macb driver sees no
reason to perform actual write to the NCFGR register, although the speed and
duplex settings in that register were reset when interface was brought down
and up. In that case actual phy speed and duplex differ from NCFGR settings.
The patch fixes that by keeping internal driver representation of speed and
duplex in sync with actual content of NCFGR.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings recently came up with a better way to handle the kconfig
dependencies for the PTP hardware clocks. This patch converts one new and
one older driver to the new scheme.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
f7b2927 introduced tx checksum offload support for smsc95xx,
and enabled it by default. This feature doesn't take
endianness into account, so causes most tx to fail on
those platforms.
This patch fixes the problem fully by adding the missing
conversion.
An alternate workaround is to disable TX checksum offload
on those platforms. The cpu impact of this feature is very low.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL_GIGA_MAC_VER_35 includes no multicast hardware filter.
Signed-off-by: Nathan Walp <faceprint@faceprint.com>
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ip link add ... type vxlan ... ttl X" allows a user to set the TTL
used by a VXLAN for encapsulation. The provided value was ignored by
vxlan module and the default value of 1 was used when encapsulating
multicast packets.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for wol wakeup on unicast, broadcast,
multicast and arp frames.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
