Rename clk_init_one() to clk_preinit() to distinguish its function
from clk_init() and the individual struct clk init functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On our system we see the following messages:
Disabling unused clock "gpt2_ick"
Disabling unused clock "gpt3_ick"
Disabling unused clock "gpt4_ick"
Disabling unused clock "gpt5_ick"
...
The messages have KERN_INFO level and if you have serial
console, they normally go there. I do not think it is good
idea to print that much stuff there. Moreover, messages
are not properly prefixed and for mortals it is not
immeadietly clear where they come from.
Let's give them debugging level instead.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: trimmed debugging output in patch description]
The CORE DPLL M2 frequency change code should use pr_debug(), not
pr_info(), for its debug messages. Same with
omap2_clksel_round_rate_div(). While here, convert a few printk(KERN_ERR ..
into pr_err().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 34xx TRM Rev. K section 11.2.4.4.11.1 "Purpose of the
DLL/CDL Module," the SDRC delay-locked-loop can be locked at any SDRC
clock frequency from 83MHz to 166MHz. CDP code unconditionally
unlocked the DLL whenever shifting to a lower SDRC speed, but this
seems unnecessary and error-prone, as the DLL is no longer able to
compensate for process, voltage, and temperature variations. Instead,
only unlock the DLL when the SDRC clock rate would be less than 83MHz.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Renumber registers in omap3_sram_configure_core_dpll() assembly code to
make space for additional parameters.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Initialize SDRC_POWER to a known-good setting when the kernel boots.
Necessary since some bootloaders don't initialize SDRC_POWER properly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Clear the SDRC_POWER.PWRENA bit before putting the SDRAM into self-refresh
mode. This prevents the SDRC from attempting to power off the SDRAM,
which can cause the system to hang.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add more barriers in the SRAM CORE DPLL M2 divider change code.
- Add a DSB SY after the function's entry point to flush all cached
and buffered writes and wait for the interconnect to claim that they
have completed[1]. The idea here is to force all delayed write
traffic going to the SDRAM to at least post to the L3 interconnect
before continuing. If these writes are allowed to occur after the
SDRC is idled, the writes will not be acknowledged and the ARM will
stall.
Note that in this case, it does not matter if the writes actually
complete to the SDRAM - it is only necessary for the writes to leave
the ARM itself. If the writes are posted by the interconnect when
the SDRC goes into idle, the writes will be delayed until the SDRC
returns from idle[2]. If the SDRC is in the middle of a write when
it is requested to enter idle, the SDRC will not acknowledge the
idle request until the writes complete to the SDRAM.[3]
The old-style DMB in sdram_in_selfrefresh is now superfluous, so,
remove it.
- Add an ISB before the function's exit point to prevent the ARM from
speculatively executing into SDRAM before the SDRAM is enabled[4].
...
1. ARMv7 ARM (DDI 0406A) A3-47, A3-48.
2. Private communication with Richard Woodruff <r-woodruff2@ti.com>.
3. Private communication with Richard Woodruff <r-woodruff2@ti.com>.
4. ARMv7 ARM (DDI 0406A) A3-48.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Mark the SRAM (aka OCM RAM) as Non-cacheable Normal memory[1]. This
is to prevent the ARM from evicting existing cache lines to SDRAM
while code is executing from the SRAM. Necessary since one of the
primary uses for the SRAM is to hold the code and data for the CORE
DPLL M2 divider reprogramming code, which must execute while the SDRC
is idled. If the ARM attempts to write cache lines back to the while
the SRAM code is running, the ARM will stall[2].
TI deals with this problem in the CDP kernel by marking the SRAM as
Strongly-ordered memory.
Tero Kristo <tero.kristo@nokia.com> caught a bug in an earlier version of
this patch - thanks Tero.
...
1. ARMv7 ARM (DDI 0406A) pp. A3-30, A3-31, B3-32.
2. Private communication with Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
With the clkdev, musb_core.c needs to register clock with name "ick".
Once all the platforms using the musb driver have been converted
to use clockdev, the clock name does not need to be passed
from the low-level init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
SPI driver will do unhandled fault on OMAP2420 if trying to probe
non-existing SPI busses. Register those additional busses runtime only
for cpus having them.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "tusb6010 init error 5, -19" and compilation warning from function
tusb6010_platform_retime "warning: 'sysclk_ps' is used uninitialized in this
function".
I suppose commit c094ba34b8f780885d029ce3c2715a194b780e5d was meant to test
for zero fclk_ps instead of sysclk_ps.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO de-bounce clocks don't have any impact on the module idle state, so
the clock code should not wait for the module to enable after the de-bounce
clocks are enabled.
Problem found by Kevin Hilman <khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Print reserved memory only if it was actually reserved.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
bonding: fix panic if initialization fails
IXP4xx: complete Ethernet netdev setup before calling register_netdev().
IXP4xx: use "ENODEV" instead of "ENOSYS" in module initialization.
ipvs: Fix IPv4 FWMARK virtual services
ipv4: Make INET_LRO a bool instead of tristate.
net: remove stale reference to fastroute from Kconfig help text
net: update skb_recycle_check() for hardware timestamping changes
bnx2: Fix panic in bnx2_poll_work().
net-sched: fix bfifo default limit
igb: resolve panic on shutdown when SR-IOV is enabled
wimax: oops: wimax_dev_add() is the only one that can initialize the state
wimax: fix oops if netlink fails to add attribute
Bluetooth: Move dev_set_name() to a context that can sleep
netfilter: ctnetlink: fix wrong message type in user updates
netfilter: xt_cluster: fix use of cluster match with 32 nodes
netfilter: ip6t_ipv6header: fix match on packets ending with NEXTHDR_NONE
netfilter: add missing linux/types.h include to xt_LED.h
mac80211: pid, fix memory corruption
mac80211: minstrel, fix memory corruption
cfg80211: fix comment on regulatory hint processing
...
From: Bruce Ashfield <bruce.ashfield@windriver.com>
To fully support the armv7-a instruction set/optimizations, support
for the R_ARM_MOVW_ABS_NC and R_ARM_MOVT_ABS relocation types is
required.
The MOVW and MOVT are both load-immediate instructions, MOVW loads 16
bits into the bottom half of a register, and MOVT loads 16 bits into the
top half of a register.
The relocation information for these instructions has a full 32 bit
value, plus an addend which is stored in the 16 immediate bits in the
instruction itself. The immediate bits in the instruction are not
contiguous (the register # splits it into a 4 bit and 12 bit value),
so the addend has to be extracted accordingly and added to the value.
The value is then split and put into the instruction; a MOVW uses the
bottom 16 bits of the value, and a MOVT uses the top 16 bits.
Signed-off-by: David Borman <david.borman@windriver.com>
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the camera device based on Guennadi's soc_camera architecture
for the mx31.
The proposed init by Guennadi was removed and must be implemented in the
board init file as it contains a lot of board specific info (memory
size, clock speed).
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is used on all board of our system, so again this is done in the
mx31moboard.c file.
changes since v2: call to gpio_request added in platform code, and
moved device initialization in baseboard files.
changes since v1: pins are claimed in another patch
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to use the gpiolib, we now have to call gpio_request in
the plaform code since it is not done in iomux code anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since iomux code is not directly related to gpio on mx31, the calls
to gpio_request are removed from iomux.c file.
These calls have to be done in platform initialization files. The
name of the singe pin call for iomux is also changed to
mxc_iomux_alloc_pin.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add OTG device definition and resources to i.MX31 and a pure USB device mode
support to the pcm037 board.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add Sharp-QVGA panel support for MX27ADS board
Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the SMSC platform device to the Litekit board.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several comments in board config files stated "mandatory for
CONFIG_LL_DEBUG" but the correct name is CONFIG_DEBUG_LL.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This support both sdhc1 and sdhc2 with WP and CD for the marxbot and
devboard mx31moboard baseboards.
sdhc2 is present on both, but is not directly included in the
mx31moboard file because a third baseboard (not supported yet) without
sdhc2 is planned.
Changes since v1: removed pin initialization from init/exit function and
taken different comments into account
Changes since v2: pin initialiation now is done in another patch for all
current mx31moboard pins
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Changes since v1: all the pins needed for the drivers are claimed in
another patch
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As suggested by Sascha, here we setup all the pins that we are using in
the current (and currently reviewed) drivers for mx31moboard system.
changes since v1: changed I2C1 pin names
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As suggested by Sascha, I regroup them in a single patch so that the
other patches become more orthogonal.
changes since v1: changed I2C1 pin names
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This hw-random driver add support to RNGA hardware found
on some i.MX processors.
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Various improvements (includes in alphabetical order, platform devices
declaration order change, ...)
The pins now are claimed in a single function call from a main table for
every board for a better clarity and to adopt the current agreement for
mx31 devices.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adds a defconfig file for the i.MX21 SoC, targeting
the Freescale i.MX21ADS (M9328MX21ADSE) Application
Development System.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* Kconfig enables now HAVE_PWM (this enables in turn the selection of
CONFIG_BACKLIGHT_PWM)
* changes CONFIG_ARCH_MXyy to CONFIG_MACH_MXyy
* fix some register names to match those of the reference manual
* write a stub code so that the PWM can be used to program the
LCD backlight
* convert from #ifdef CONFIG_ARCH_MXxx to cpu_is_mxXX()
* remove unneeded defines and fix 80-column "violations" of checkpatch.pl
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[PATCH v6] MXC: mx21ads base support
Base machine support for the Freescale i.MX21ADS
(M9328MX21ADSE) Application Development System.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MXC GPIO controller does not support generation of interrupts on both
edges. Emulate this mode in software by reconfiguring the irq trigger
polarity on each interrupt. This follows an example of
drivers/mfd/asic3.c.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch-imx is superseeded by the MXC architecture support.
This patch removes arch/arm/mach-imx from the kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch-imx is superseeded by the MXC architecture support.
This patch removes arch-imx from the build system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently we depend on hardcoded base addresses for the interrupt
controller. This prevents us from compiling in more than one i.MX
architecture at a time. This patch changes the base address to a
runtime calculated one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently we depend on hardcoded base addresses for the timer.
This prevents us from compiling in more than one i.MX architecture
at a time. This patch changes the base address to a runtime
calculated one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows us to have more mapping functions for more than one
i.MX architecture in the kernel. As this is the earliest board
specific hook we have, also use it to set the cpu type.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It is no longer present in newer cores. Unfortunately Freescale decided
to put the bit which decides between automotive clock path and consumer
clock path in the automotive clock path direction. With current code we
cannot detect the core revision, so just remove automotive path completely.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This iomux is called iomux-v3 in the tree because it is the third known
incarnation of MXC iomuxers. It is not only found on the MX35 but also
on the MX51 and probably others.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As per commit 284901a90a, use
DMA_BIT_MASK(n)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The structure 'arch_mmu' accommodates the difference between omap1 and
omap2/3.
This patch provides omap2/3 specific functions
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
The i.MX31 ARM11 core is not a v6K core. Disable this option as it
is incompatible with non v6K cores.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Before this patch I got the following line in my dmesg:
[ 0.000000] BUG: mapping for 0xd4000000 at 0xeb000000 overlaps vmalloc space
VMALLOC_END is 0xf4000000 and there are the following other mappings
defined for mx27ads:
(0xa0500000,+0x00001000) maps to 0xffff0000
(0x10000000,+0x00100000) maps to 0xf4000000
(0x80000000,+0x00100000) maps to 0xf4100000
(0xd8000000,+0x00100000) maps to 0xf4200000
So map PBC to 0xf4300000.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On i.MX31 I sometimes get spurious interrupts. There is no need
to crash the whole system when this happens. Instead, silently
ignore it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We want to have a mx31_defconfig file that builds a kernel that is able
to boot on all support mx31 systems and thus also can be better tested
by automatic build scripts. For these reasons, this config file is not
needed anymore.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All i.MX platforms support <linux/clk.h> calls and should select HAVE_CLK.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On MX2 platforms imx_dma_request() calls request_irq() which may sleep
with interrupts disabled.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The sequence
imx_dma_request()
imx_dma_enable()
imx_dma_free()
left the dma channel in_use mode and did not release the timer.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
[ARM] 5489/1: ARM errata: Data written to the L2 cache can be overwritten with stale data
[ARM] 5490/1: ARM errata: Processor deadlock when a false hazard is created
[ARM] 5487/1: ARM errata: Stale prediction on replaced interworking branch
[ARM] 5488/1: ARM errata: Invalidation of the Instruction Cache operation can fail
davinci: DM644x: NAND: update partitioning
davinci: update DM644x support in preparation for more SoCs
davinci: DM644x: rename board file
davinci: update pin-multiplexing support
davinci: serial: generalize for more SoCs
davinci: DM355 IRQ Definitions
davinci: DM646x: add interrupt number and priorities
davinci: PSC: Clear bits in MDCTL reg before setting new bits
davinci: gpio bugfixes
davinci: add EDMA driver
davinci: timers: use clk_get_rate()
[ARM] pxa/littleton: add missing da9034 touchscreen support
[ARM] pxa/zylonite: configure GPIO18/19 correctly, used by 2 GPIO expanders
[ARM] pxa/zylonite: fix the issue of unused SDATA_IN_1 pin get AC97 not working
[ARM] pxa: make ads7846 on corgi and spitz to sync on HSYNC
[ARM] pxa: remove unused CPU_FREQ_PXA Kconfig symbol
...
The alterations to the suspend code missed adding a
call to the cache flushing routines during the suspend
path of the S3C2412.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch is a workaround for the 460075 Cortex-A8 (r2p0) erratum. It
configures the L2 cache auxiliary control register so that the Write
Allocate mode for the L2 cache is disabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a workaround for the 458693 Cortex-A8 (r2p0)
erratum. It sets the corresponding bits in the auxiliary control
register so that the PLD instruction becomes a NOP.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the workaround for the 430973 Cortex-A8 (r1p0..r1p2)
erratum. The BTAC/BTB is now flushed at every context switch.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements the recommended workaround for erratum 411920
(ARM1136, ARM1156, ARM1176).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In clock.c file the clock management is grouped by cpu with cpu_is_xxx()
function. This lead to some kind of difficulties to read this file and
maintainability issues as the number of AT91 cpus & PLLs/clocks is growing.
In this patch, I try to group clock functionality together and match cpus with
this functionality set.
An update to at91_pmc.h is needed to cover some new PMC possibilities (and
some update in comments).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arm is placing some code in the .text.init section, but it does not
reference that section in its linker scripts.
This change moves this code from the .text.init section to the
.init.text section, which is presumably where it belongs.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update NAND partitioning for the dm6446 evm, unmasking the hidden
data at the beginning and letting the kernel be updated from Linux.
- This is boot-compatible with TI's software (U-Boot 1.20 and both
the 2.6.10 and 2.6.18 kernels), in terms of startup and loading
kernels from flash.
- In the same way, it's also boot-compatible with mainline U-Boot,
which stores U-Boot params in block 0 not block 16.
- It's not quite compatible with systems that previously used NAND
partitions to hold (filesystem) data. The compatibilities are a
bit different based on which kernel was used previously
+ Users of TI/MV kernels no longer see mtd2 "params"
(mainline u-boot env is in a different place)
* Filesystem is now mtd2 ... vs mtd3
+ Users of GIT kernels now see mtd0 and mtd1 partitions
* Filesystem partition starts 640 KBytes earlier
* Filesystem is now mtd2 ... vs mtd0
* Linux now *uses* the flash-resident BBT
* Removes annoying slowdown/hiccup during boot
* Potentially ~64KB less space available with TI/MV kernels
If you *used* NAND partitions from Linux, there is no solution that's
fully compatible with all previous kernels in those respects ... ergo
this "best compromise". It'd be good to back back up the filesystem
data; or, carry your own backwards-compatibility patch for awhile.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rework DM644x code into SoC specific and board specific parts.
This is also to generalize the structure a bit so it's easier to add
support for new SoCs in the DaVinci family.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename DM6446 EVM board file, no functional changes. Code is updated
and reworked in following patch.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adding IRQ defintions for DaVinci DM355 and default interrupt
priorities for DM355
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Clear any set bits in the 'NEXT' field of the MDCTL register in the
Power and Sleep Controller (PSC) before setting any new bits.
This also allows some minor cleanup by removing some no longer
needed lines of code.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Update the DaVinci GPIO code to work better on non-dm6446 parts,
notably the dm355:
- Only handle the number of GPIOs the chip actually has. So
for example on dm6467, GPIO-42 is the last GPIO, and trying
to use GPIO-43 now fails cleanly; or GPIO-72 on dm6446.
- Enable GPIO interrupts on each 16-bit GPIO-irq bank ...
previously, only the first five were enabled, so GPIO-80
and above (on dm355) wouldn't trigger IRQs.
- Use the right IRQ for each GPIO bank. The wrong values were
used for dm355 chips, so GPIO IRQs got routed incorrectly.
- Handle up to four pairs of 16-bit GPIO banks ... previously
only three were handled, so accessing GPIO-96 and up (e.g. on
dm355) would oops.
- Update several comments that were dm6446-specific.
Verified by receiving GPIO-1 (dm9000) and GPIO-5 (msp430) IRQs
on the DM355 EVM.
One thing this doesn't do is handle the way some of the GPIO
numbers on dm6467 are reserved but aren't valid as GPIOs. Some
bitmap logic could fix that if needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Original code for 2.6.10 and 2.6.28 series done by Texas Instruments
and MontaVista, but major updates and rework done by Troy Kisky and
David Brownell.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use clock framework instead of hard-coded CLOCK_TICK_RATE for
determining timer tick frequencies.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
GPIO17_SDATA_IN_1 and GPIO36_SDATA_IN_1 are originally designed for the 2nd
codec but unused on the board, yet they are initialized incorrectly by the
bootloader as the SDATA_IN_1 alternate function, thus causing AC97 fail to
work. Fix this issue by configuring these pins as normal GPIO to avoid the
noise from these pins being treated as signals from the 2nd codec.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
cpufreq drivers for pxa2xx/3xx are now built-in automatically as soon as
CPU_FREQ is enabled.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
ARCH_PXA selects HAVE_CLK and COMMON_CLKDEV twice in arch/arm/Kconfig.
Remove the second entry.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
pxa_gpio_irq_type() and pxa_unmask_muxed_gpio() will touch non-muxed GPIOs
(0 and 1 on PXA2xx/PXA3xx) bits in GRERx and GFERx, which is incorrect.
Actually, only those bits should get updated if the corresponding bits are
set in c->irq_mask as well. Fix this by updating only those relevant bits.
Reported-and-tested-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Update the rtc-ep93xx driver to use ioremap'ed addresses.
This removes the dependency on <mach/hardware.h> and properly
reports the memory addresses used by the driver in /proc/iomem.
In addition, ep93xx_rtc_init() is updated to use
platform_driver_probe() instead of platform_driver_register().
Also, the device_create_file() calls are now properly checked for
error conditions. The created sysfs files are also now removed
when the driver is removed.
The version number for the driver has been bumped at the request
of Alessandro Zummo.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the long run, we may want to place page tables in highmem. However,
pmd_page() has traditionally been coded to convert the physical address
to a virtual one, which won't work with highmem pages. Instead,
translate the physical address to a PFN, and then convert the PFN to a
struct page instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a function omap2_gp_clockevent_set_gptimer() for board-*.c files
to use in .init_irq functions to configure the system tick GPTIMER.
Practical choices at this point are GPTIMER1 or GPTIMER12. Both of
these timers are in the WKUP powerdomain, and so are unaffected by
chip power management. GPTIMER1 can use sys_clk as a source, for
applications where a high-resolution timer is more important than
power management. GPTIMER12 has the special property that it has the
secure 32kHz oscillator as its source clock, which may be less prone
to glitches than the off-chip 32kHz oscillator. But on HS devices, it
may not be available for Linux use.
It appears that most boards are fine with GPTIMER1, but BeagleBoard
should use GPTIMER12 when using a 32KiHz timer source, due to hardware bugs
in revisions B4 and below. Modify board-omap3beagle.c to use GPTIMER12.
This patch originally used a Kbuild config option to select the GPTIMER,
but was changed to allow this to be specified in board-*.c files, per
Tony's request.
Kalle Vallo <kalle.valo@nokia.com> found a bug in an earlier version of
this patch - thanks Kalle.
Tested on Beagle rev B4 ES2.1, with and without CONFIG_OMAP_32K_TIMER, and
3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
All GP timers on OMAP2/3 can generate wakeup events. The wakeup status is
cleared in the PRCM interrupt handler.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Typo error when requesting for clock for dsp in omap1
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch avoids waiting for the camera module to become ready,
since it doesn't have IDLEST bit.
Based on a earlier hack done by Paul Walmsley on Sep 9 2008 on
linux-omap tree.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 8ad8ff6548 breaks the OMAP2xxx
cpu_mask code, which causes OMAP2xxx to panic on boot. Fix by
removing the cpu_mask auto variable and by changing CK_242X
and CK_243X to use RATE_IN_242X/RATE_IN_243X.
Resolves
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<1>pgd = c0004000
<1>[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1]
Modules linked in:
CPU: 0 Not tainted (2.6.29-omap1 #32)
PC is at omap2_clk_set_parent+0x104/0x120
LR is at omap2_clk_set_parent+0x28/0x120
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed. This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.
Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.
This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SPURIOUSIRQ is contained in bits 31:7 of INTC_SIR, so
INTC_SIR must be right shifted by 7, not 6.
No change in logic, only changes for better readability.
Refer to register definition of INTCPS_SIR_IRQ in OMAP3 Manual.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Flush posted write to IRQSTATUS register in GPIO IRQ handler.
This eliminates the below error for all peripherals that use GPIO interrupts.
<4>Spurious irq 95: 0xffffffdf, please flush posted write for irq 31
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO IRQ enable/disable path attempts to also enable IRQ wake
support for the parent GPIO bank IRQ as well. However, since there is
no 'set_wake' hook for the bank IRQs, these calls will always fail.
Also, since the enable will fail on the suspend path, the disable on
the resume path will trigger unbalanced enable/disable warnings.
This was discovered in the suspend/resume path on OMAP3/Beagle using
the gpio-keys driver which disables/re-enables GPIO IRQ wakeups in the
suspend/resume path.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In linus' git tree the functions can be found at:
vi arch/arm/mach-omap2/usb-tusb6010.c +200 - tusb6010_platform_retime()
vi arch/arm/mach-omap2/gpmc.c +94 - gpmc_get_fclk_period()
vi arch/arm/mach-omap2/usb-tusb6010.c +53 - tusb_set_async_mode()
vi arch/arm/mach-omap2/usb-tusb6010.c +111 - tusb_set_sync_mode()
is -ENODEV appropriate when sysclk_ps == 0?
This was found by code analysis, please review.
------------------------------>8-------------8<---------------------------------
gpmc_get_fclk_period() may return 0 when gpmc_l3_clk is not enabled. This is
not checked in tusb6010_platform_retime() nor in tusb_set_async_mode() it
seems. In tusb_set_sync_mode() this may result in a division by zero.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no anymore legacy driver for OMAP24XX Enhanced Audio Controller
in linux-omap and it was newer in mainline so cleanup these unneeded
defines and initialization code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This should be done with GPIO calls. Patches against the
mainline tree welcome to add the necessary working functionality
back.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the possible race condition in omap_free_dma(). Function omap_free_dma()
sets the dev_id = -1 and then accesses the channel afterwards to clear it.
But setting the dev_id=-1 makes the channel available for allocation again.
So it is possible someone else can grab it and results are unpredictable.
To avod this DMA channle is cleared first and then the dev_id = -1 is set.
Thanks to McNeil, Sean <sean.mcneil@ti.com> for ointing out this issue.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add arch-specific ioremap() which uses any existing static mappings in
place of doing a new mapping. From now on, drivers should always use
ioremap() instead of IO_ADDRESS().
In addition, remove the davinci_[read|write]* macros in favor of using
ioremap.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This is a significant rework of the low-level clock, PLL and Power
Sleep Controller (PSC) implementation for the DaVinci family. The
primary goal is to have better modeling if the hardware clocks and
features with the aim of DVFS functionality.
Highlights:
- model PLLs and all PLL-derived clocks
- model parent/child relationships of PLLs and clocks
- convert to new clkdev layer
- view clock frequency and refcount via /proc/davinci_clocks
Special thanks to significant contributions and testing by David
Brownell.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Commit 3f0a820c4c breaks OMAP2xxx boot
during initial propagate_rate() on osc_ck and sys_ck. Fix by
pre-initializing all struct clks before running any other clock init
code. Incorporates review comments from Russell King
<rmk+kernel@arm.linux.org.uk>.
Resolves
<1>Unable to handle kernel NULL pointer dereference at virtual address 00000000
<1>pgd = c0004000
<1>[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
Modules linked in:
CPU: 0 Not tainted (2.6.29-omap1 #37)
PC is at propagate_rate+0x10/0x60
LR is at omap2_clk_init+0x30/0x218
...
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a version incorporating Christoph's suggestion.
Separate out common *fstatat functionality into a single function
instead of duplicating it all over the code.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
From: David Brownell <dbrownell@users.sourceforge.net>
Fix GPIO-related build error on mach-imx platform:
CC drivers/spi/spi_gpio.o
In file included from /home/db/kernel/scratch/arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:7,
from drivers/spi/spi_gpio.c:23:
arch/arm/mach-imx/include/mach/gpio.h: In function 'imx_gpio_get_value':
arch/arm/mach-imx/include/mach/gpio.h:27: error: implicit declaration of function '__REG2'
arch/arm/mach-imx/include/mach/gpio.h:27: error: 'IMX_IO_BASE' undeclared (first use in this function)
arch/arm/mach-imx/include/mach/gpio.h:27: error: (Each undeclared identifier is reported only once
arch/arm/mach-imx/include/mach/gpio.h:27: error: for each function it appears in.)
arch/arm/mach-imx/include/mach/gpio.h: In function 'imx_gpio_set_value_inline':
arch/arm/mach-imx/include/mach/gpio.h:36: error: 'IMX_IO_BASE' undeclared (first use in this function)
arch/arm/mach-imx/include/mach/gpio.h:36: error: lvalue required as left operand of assignment
arch/arm/mach-imx/include/mach/gpio.h:38: error: lvalue required as left operand of assignment
...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel 2.6.30-rc1 added sys_preadv and sys_pwritev to most archs
but not ARM, resulting in
<stdin>:1421:2: warning: #warning syscall preadv not implemented
<stdin>:1425:2: warning: #warning syscall pwritev not implemented
This patch adds sys_preadv and sys_pwritev to ARM.
These syscalls simply take five long-sized parameters, so they
should have no calling-convention/ABI issues in the kernel.
Tested on armv5tel eabi using a preadv/pwritev test program posted
on linuxppc-dev earlier this month.
It would be nice to get this into the kernel before 2.6.30 final,
so that glibc's kernel version feature test for these syscalls
doesn't have to special-case ARM.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As a result of an off-by-1 error pcm990 leaves one unused GPIO number between
built-in GPIOs and the pca9536 extender. Fix it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Firstly, this patch makes the palm27x asoc driver a little more sane. Also,
since all affected devices use GPIO95 as AC97_nRESET, this patch sets that
properly. Affected are PalmT5, TX and LifeDrive.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Check pending queue and remove the adc client being released.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The symbol 's3c_adc_try' in arch/arm/plat-s3c24xx/adc.c
does not need to be exported and thus should be static.
This fixes the following sparse warning:
adc.c:103:6: warning: symbol 's3c_adc_try' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The .init_machine entry in mach-osiris.c had the same entry
twice, so remove one definition to fix the following warning
from sparse:
mach-osiris.c:416:3: warning: Initializer entry defined twice
mach-osiris.c:418:3: also defined here
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make 'anubis_ide_platdata' statis as it is not used outside
the file it is in, fixing the following sparse warning:
mach-anubis.c:246:27: warning: symbol 'anubis_ide_platdata' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make 'jive_vgg2432a4_display' and 'jive_lcd_config' static as
they are not exported, and are generating the following sparse
warnings:
mach-jive.c:280:26: warning: symbol 'jive_vgg2432a4_display' was not declared. Should it be static?
mach-jive.c:313:28: warning: symbol 'jive_lcd_config' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warning due to s3c_device_hwmon being
missing from <plat/devs.h>
devs.c:380:24: warning: symbol 's3c_device_hwmon' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse error generated by including
<plat/gpio-core.h> instead of <mach/gpio-core.h>
gpiolib.c:78:22: warning: symbol 's3c24xx_gpios' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The VIC code will attempt to perform som
default set_irq_chip() and set_irq_chip_data()
on all IRQs supported by the VIC, while the new
IRQ handling code strictly checks for the global
NR_IRQS to be respected also for these IRQs.
This patch will respect the interrupt mask passed
to the VIC driver and will prevent it from
attempting to call these functions on any unused
interrupts.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes several i.MX board specific defconfig files in favour
for a mx1_defconfig, mx27_defconfig and mx3_defconfig. All config files
have all currently available boards, i.MX specific drivers and the network
device drivers for the boards enabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move ifdef under function brackets. This fixes compile crach when IRQ priorities
are disabled.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
AIPS[12] are no mapped from generic MX3 code so we don't need to
map them from machine-specific map_io function anymore.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Set the correct clkdev-name for the i2c clock.
It also get's rid of the ARCH_NR_GPIOS define on the rationale
that isn't an ARCH-wide setting anyway. If a device has two
pca953x devices, the reserved number will be wrong.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Add an export of the two GPIO configuration calls
s3c_gpio_cfgpin and s3c_gpio_setpull to allow modules
to use them (such as ASoC drivers)
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the filesystem options in the s3c2410_defconfig,
such as building ext4, enable the automounter as modules
and update the network filesysyem choices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It seems that declarations of kmalloc/kfree are missed, explicitly
include it.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add SD/MMC to the s3c2410_defconfig, building in the core
and adding the rest of the drivers as modules.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the machine configuration of s3c2410_defconfig to
add support for newer machines, and update the s3c24xx
specific options.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Update the list of modules being built for the network
core of the s3c2410_defconfig. This update adds such
items as TCP congestion, netfilter for IPv4 and IPv6.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Going forward gpio_request() will be a requirement for GPIO API users so
call it for the LCD power GPIOs. With present code the kernel functions
but generaets loud WARN_ON()s when using the unrequested GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix trivial build warning due to incompatible pointer type.
ep93xx_timer_interrupt() has the wrong return type causing a
warning during the build.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When unmapping N pages (e.g. shared memory) the amount of TLB flushes
done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it should be N at
maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8 pages, so there is a
noticeable performance penalty when unmapping a large VMA and the system
is spending its time in flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh Dickins,
and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger mappings
even more.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MioA701 board's GPIO95 is the AC97 line. The other GPIO113
is not connected to the sound chip, but to the GSM chip as a
wakeup line.
It happens that when the pxa2xx_ac97 driver reconfigures the
gpio as an "out gpio" for AC97 reset (bug workaround), it
hangs the GSM chip.
As AC97 platform data now enables to specify the AC97 reset
line, use it.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Currently there are two possible platform datas for the PXA AC97 driver:
one supported by the generic AC97 driver only which provides callbacks
to allow board-specific configuration at stream startup and teardown,
and another for pxa2xx-ac97-lib which allows configuration of the reset
GPIO for PXA2xx CPUs.
Obviously this won't actually work when using the generic AC97 driver
since the drivers will attempt to parse the platform data in both
formats. Fix this by merging the two structures.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
After commit a7bb3909b3 ("spi: pxa2xx_spi:
introduce chipselect GPIO to simplify the common cases") the .gpio_cs
field in pxa2xx_spi_chip has to be set explicitly.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
