On BE MIPS systems this needs to use the new IRQ_GC_BE_IO gc_flag. In
all other cases it will use the standard readl/writel accessors.
The initial irq_fwd_mask setup runs before "gc" is initialized, so it
is unchanged for now. This could potentially be a problem on an ARM
system that boots in LE mode but runs a BE kernel, but currently none
of the supported ARM platforms are ever expected to run BE.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/1415342669-30640-14-git-send-email-cernekee@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some chips, such as BCM6328, only require bcm7120-l2. Some BCM7xxx STB
configurations only require brcmstb-l2. Treat them as two separate
entities, and update the mach-bcm dependencies to reflect the change.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lkml.kernel.org/r/1415342669-30640-13-git-send-email-cernekee@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Most implementations of the bcm7120-l2 controller only have a single
32-bit enable word + 32-bit status word. But some instances have added
more enable/status pairs in order to support 64+ IRQs (which are all
ORed into one parent IRQ input). Make the following changes to allow
the driver to support this:
- Extend DT bindings so that multiple words can be specified for the
reg property, various masks, etc.
- Add loops to the probe/handle functions to deal with each word
separately
- Allocate 1 generic-chip for every 32 IRQs, so we can still use the
clr/set helper functions
- Update the documentation
This uses one domain per bcm7120-l2 DT node. If the DT node defines
multiple enable/status pairs (i.e. >=64 IRQs) then the driver will
create a single IRQ domain with 2+ generic chips. Multiple generic chips
are required because the generic-chip code can only handle one
enable/status register pair per instance.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/1415342669-30640-12-git-send-email-cernekee@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The cached value already incorporates irq_fwd_mask, and was saved the
last time an IRQ was enabled/disabled.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/1415342669-30640-11-git-send-email-cernekee@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This mask should have been 0xffff_ffff, not 0x0fff_ffff.
The change should not have an effect on current users (STB) because bits
31:27 are unused.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lkml.kernel.org/r/1415342669-30640-10-git-send-email-cernekee@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A couple of accesses to IRQEN (base+0x00) just used "base" directly, so
they would break if IRQEN ever became nonzero. Make sure that all
reads/writes specify the register offset constant.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/1415342669-30640-9-git-send-email-cernekee@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This check may be prone to race conditions, e.g.
1) Some external event (e.g. GPIO level) causes an IRQ to become pending
2) Peripheral asserts the L2 IRQ
3) CPU takes an interrupt
4) The event from #1 goes away
5) bcm7120_l2_intc_irq_handle() reads back a 0 status
Unlike the hardware supported by brcmstb-l2, the bcm7120-l2 controller
does not latch the IRQ status. Bits can change if the inputs to the
controller change. Also, do_bad_IRQ() is an ARM-specific macro.
So let's just nuke it.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/1415342669-30640-7-git-send-email-cernekee@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds support for the Level-2 interrupt controller
hardware found in Broadcom Set Top Box System-on-a-Chip devices. This
interrupt controller is implemented using a single enable register.
This interrupt controller is always present on the platforms supported
by the irq-brcmstb-l2 driver, hence the reason why both are compiled
using the same Kconfig symbol.
[jac] removed the following warning:
drivers/irqchip/irq-bcm7120-l2.c: In function 'bcm7120_l2_intc_irq_handle':
drivers/irqchip/irq-bcm7120-l2.c:49:27: warning: unused variable 'gc' [-Wunused-variable]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lkml.kernel.org/r/1410309862-27784-2-git-send-email-f.fainelli@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
