Core:
- Expose access to the eMMC RPMB ("Replay Protected Memory Block") area
by extending the existing mmc_block ioctl.
- Add SDIO powered-suspend DT properties to the core MMC DT binding.
- Add no-1-8-v DT flag for boards where the SD controller reports that it
supports 1.8V but the board itself has no way to switch to 1.8V.
- More work on switching to 1.8V UHS support using a vqmmc regulator.
- Fix up a case where the slot-gpio helper may fail to reset the host
controller properly if a card was removed during a transfer.
- Fix several cases where a broken device could cause an infinite loop
while we wait for a register to update.
Drivers:
- at91-mci: Remove obsolete driver, atmel-mci handles these devices now.
- sdhci-dove: Allow using GPIOs for card-detect notifications.
- sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
- sdhci-s3c: Add pinctrl support.
- wmt-sdmmc: New driver for WonderMedia SD/MMC controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=oSX3
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.8:
Core:
- Expose access to the eMMC RPMB ("Replay Protected Memory Block")
area by extending the existing mmc_block ioctl.
- Add SDIO powered-suspend DT properties to the core MMC DT binding.
- Add no-1-8-v DT flag for boards where the SD controller reports
that it supports 1.8V but the board itself has no way to switch to
1.8V.
- More work on switching to 1.8V UHS support using a vqmmc regulator.
- Fix up a case where the slot-gpio helper may fail to reset the host
controller properly if a card was removed during a transfer.
- Fix several cases where a broken device could cause an infinite
loop while we wait for a register to update.
Drivers:
- at91-mci: Remove obsolete driver, atmel-mci handles these devices
now.
- sdhci-dove: Allow using GPIOs for card-detect notifications.
- sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
- sdhci-s3c: Add pinctrl support.
- wmt-sdmmc: New driver for WonderMedia SD/MMC controllers."
* tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (65 commits)
mmc: sdhci: implement the .card_event() method
mmc: extend the slot-gpio card-detection to use host's .card_event() method
mmc: add a card-event host operation
mmc: sdhci-s3c: Fix compilation warning
mmc: sdhci-pci: Enable SDHCI_CAN_DO_HISPD for Ricoh SDHCI controller
mmc: sdhci-dove: allow GPIOs to be used for card detection on Dove
mmc: sdhci-dove: use two-stage initialization for sdhci-pltfm
mmc: sdhci-dove: use devm_clk_get()
mmc: eSDHC: Recover from ADMA errors
mmc: dw_mmc: remove duplicated buswidth code
mmc: dw_mmc: relocate where dw_mci_setup_bus() is called from
mmc: Limit MMC speed to 52MHz if not HS200
mmc: dw_mmc: use devres functions in dw_mmc
mmc: sh_mmcif: remove unneeded clock connection ID
mmc: sh_mobile_sdhi: remove unneeded clock connection ID
mmc: sh_mobile_sdhi: fix clock frequency printing
mmc: Remove redundant null check before kfree in bus.c
mmc: Remove redundant null check before kfree in sdio_bus.c
mmc: sdhci-imx-esdhc: use more devm_* functions
mmc: dt: add no-1-8-v device tree flag
...
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.
From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation):
The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.
There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
capabilities register and
- MMC/SD clock coming out of controller > 25MHz
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+UN
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
Remaining patches to allow omap2+ to build with multiplatform
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
* tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_2420_data.c
arch/arm/mach-omap2/omap_hwmod_2430_data.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/headers
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes fixed up in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JSAM
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/devel-prcm-signed' into omap-for-v3.8/cleanup-headers-prepare-multiplatform-v3
omap prcm changes via Paul Walmsley <paul@pwsan.com>:
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/cm33xx.c
arch/arm/mach-omap2/io.c
arch/arm/mach-omap2/prm_common.c
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XZ+L
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Timer clean-up to get us closer to moving timer code to drivers,
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
By Jon Hunter (32) and others
via Tony Lindgren
* tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (71 commits)
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: OMAP2+: Fix compiler warning for 32k timer
ARM: OMAP: Remove unnecessary inclusion of dmtimer.h
ARM: OMAP: Add platform data header for DMTIMERs
ARM: OMAP: Remove unnecessary omap_dm_timer structure declaration
ARM: OMAP2+: Remove unnecessary local variable in timer code
ARM: OMAP: Don't store timers physical address
ARM: OMAP: Define omap_dm_timer_prepare function as static
ARM: OMAP: Clean-up dmtimer reset code
ARM: OMAP: Remove __omap_dm_timer_set_source function
ARM: OMAP: Remove unnecessary call to clk_get()
ARM: OMAP: Add dmtimer interrupt disable function
ARM: OMAP: Fix spurious interrupts when using timer match feature
ARM: OMAP: Don't restore DMTIMER interrupt status register
ARM: OMAP: Don't restore of DMTIMER TISTAT register
ARM: OMAP: Fix dmtimer reset for timer1
ARM: OMAP2+: Don't use __omap_dm_timer_reset()
ARM: OMAP2/3: Define HWMOD software reset status for DMTIMERs
ARM: OMAP3: Correct HWMOD DMTIMER SYSC register declarations
...
Change/change conflict in arch/arm/mach-omap2/board-cm-t3517.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
CONFIG_OMAP_32K_TIMER is kind of standing on the single zImage way.
Make OMAP2+ timer code independant from the CONFIG_OMAP_32K_TIMER
setting.
To remove the dependancy, several conversions/additions had to be done:
1) Timer initialization functions are named by the platform
name and the clock source in use.
This also makes it possible to define and use the GPTIMER as the
clock source instead of the 32K timer on platforms that do not have
the 32K timer ip block or the 32K timer is not wired on the board.
Currently, the the timer is chosen in the machine_desc structure on
per board basis. Later, DT should be used to choose the timer.
2) Settings under the CONFIG_OMAP_32K_TIMER option are used as defaults
and those under !CONFIG_OMAP_32K_TIMER are removed.
This removes the CONFIG_OMAP_32K_TIMER on OMAP2+ timer code.
3) Since we have all the timers defined inside machine_desc structure
and we no longer need the fallback to gp_timer clock source in case
32k_timer clock source is unavailable (namely on AM33xx), we no
longer need the #ifdef around omap2_sync32k_clocksource_init()
function. Remove the #ifdef CONFIG_OMAP_32K_TIMER around the
omap2_sync32k_clocksource_init() function.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This file should not be in arch/arm. Move it to drivers/iommu
to allow making most of the header local to drivers/iommu.
This is needed as we are removing plat and mach includes
from drivers for ARM common zImage support.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the iommu framework does not have generic functions
exported for all the needs yet. The hardware specific functions
are defined in files like intel-iommu.h and amd-iommu.h. Follow
the same standard for omap-iommu.h.
This is needed because we are removing plat and mach includes
for ARM common zImage support. Further work should continue
in the iommu framework context as only pure platform data will
be communicated from arch/arm/*omap*/* code to the iommu
framework.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The iopgtable header file is only used by the iommu & iovmm drivers, so
move it to drivers/iommu/, as part of the single zImage effort.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
[tony@atomide.com: updated to be earlier in the series]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since iommu is not supported on OMAP1 and will not likely to ever be
supported, merge plat/iommu2.h into iommu.h so only one file would have
to move to platform_data/ as part of the single zImage effort.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove unnecessary declaration of structure omap_dm_timer from dmtimer.h and
move the actual declaration of structure omap_dm_timer towards top of dmtimer.h
to avoid any compilation errors.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The OMAP2+ system timer code stores the physical address of the timer
but never uses it. Remove this and clean-up the code by removing the
local variable "size" and changing the names of the local variables
mem_rsrc and irq_rsrc to mem and irq, respectively.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The omap_dm_timer_prepare function is a local function only used in the
dmtimer.c file. Therefore, make this a static function and remove its
declaration from the dmtimer.h file.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Only OMAP1 devices use the omap_dm_timer_reset() and so require the
omap_dm_timer_wait_for_reset() and __omap_dm_timer_reset() functions.
Therefore combine these into a single function called omap_dm_timer_reset()
and simplify the code.
The omap_dm_timer_reset() function is now the only place that is using the
omap_dm_timer structure member "sys_stat". Therefore, remove this member and
just use the register offset definition to simplify and clean-up the code. The
TISTAT register is only present on revision 1 timers and so check for this in
the omap_dm_timer_reset() function.
Please note that for OMAP1 devices, the TIOCP_CFG register does not have the
clock-activity field and so when we reset the timer for an OMAP1 device we
only need to configure the idle-mode field in the TIOCP_CFG register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Conflicts:
drivers/video/omap2/dss/Kconfig
drivers/video/omap2/omapfb/omapfb-ioctl.c
drivers/video/omap2/omapfb/omapfb-main.c
Merge changes to make omapfb use common dma_alloc, and remove omap's
custom vram allocator.
Second set of OMAP PRCM cleanups for 3.8.
These patches remove the use of omap_prcm_get_reset_sources() from the
OMAP watchdog driver, and remove mach-omap2/prcm.c and
plat-omap/include/plat/prcm.h.
Basic test logs for this branch on top of Tony's cleanup-prcm branch
at commit 7fc54fd308 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_b_3.8/20121108151646/
However, cleanup-prcm at 7fc54fd3 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_prcm_cleanup_b_3.8/20121108151930/
which indicate that the series tests cleanly.
This second pull request updates one of the patches which broke
with rmk's allnoconfigs, and also updates the tag description to
indicate that 7fc54fd3 is building cleanly here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=tS2z
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-prcm-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren <tony@atomide.com>:
More PRCM cleanups via Paul Walmsley <paul@pwsan.com>:
Second set of OMAP PRCM cleanups for 3.8.
These patches remove the use of omap_prcm_get_reset_sources() from the
OMAP watchdog driver, and remove mach-omap2/prcm.c and
plat-omap/include/plat/prcm.h.
Basic test logs for this branch on top of Tony's cleanup-prcm branch
at commit 7fc54fd308 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_b_3.8/20121108151646/
However, cleanup-prcm at 7fc54fd3 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_prcm_cleanup_b_3.8/20121108151930/
which indicate that the series tests cleanly.
This second pull request updates one of the patches which broke
with rmk's allnoconfigs, and also updates the tag description to
indicate that 7fc54fd3 is building cleanly here.
* tag 'omap-for-v3.8/cleanup-prcm-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
ARM: OMAP2: Fix compillation error in cm_common
ARM: OMAP2+: PRCM: remove obsolete prcm.[ch]
ARM: OMAP2+: hwmod: call to _omap4_disable_module() should use the SoC-specific call
ARM: OMAP2+: PRCM: consolidate PRCM-related timeout macros
ARM: OMAP2+: PRCM: split and relocate the PRM/CM globals setup
ARM: OMAP2+: PRCM: remove omap2_cm_wait_idlest()
ARM: OMAP2+: CM/clock: convert _omap2_module_wait_ready() to use SoC-independent CM functions
ARM: OMAP2xxx: APLL/CM: convert to use omap2_cm_wait_module_ready()
ARM: OMAP2+: board files: use SoC-specific system restart functions
ARM: OMAP2+: PRCM: create SoC-specific chip restart functions
ARM: OMAP2xxx: clock: move virt_prcm_set code into clkt2xxx_virt_prcm_set.c
ARM: OMAP2xxx: clock: remove global 'dclk' variable
ARM: OMAP2/3: PRM: add SoC reset functions (using the CORE DPLL method)
ARM: OMAP2+: common: remove mach-omap2/common.c globals and map_common_io code
ARM: OMAP2+: PRCM: remove omap_prcm_get_reset_sources()
watchdog: OMAP: use standard GETBOOTSTATUS interface; use platform_data fn ptr
ARM: OMAP2+: WDT: move init; add read_reset_sources pdata function pointer
ARM: OMAP1: CGRM: fix omap1_get_reset_sources() return type
ARM: OMAP2+: PRM: create PRM reset source API for the watchdog timer driver
ARM: OMAP1: create read_reset_sources() function (for initial use by watchdog)
...
Conflicts:
arch/arm/mach-omap2/cm33xx.c
arch/arm/mach-omap2/io.c
arch/arm/mach-omap2/prm_common.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
OMAP specific vram allocator is no longer used, and we can remove init
call to the vram allocator.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use DMA_BIT_MASK() for fb's coherent_dma_mask for clarity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The __omap_dm_timer_set_source() function is only used by the system timer
(clock-events and clock-source) code for OMAP2+ devices. Therefore, we can
remove this code from the dmtimer driver and move it to the system timer
code for OMAP2+ devices.
The current __omap_dm_timer_set_source() function calls clk_disable() before
calling clk_set_parent() and clk_enable() afterwards. We can avoid these calls
to clk_disable/enable by moving the calls to omap_hwmod_setup_one() and
omap_hwmod_enable() to after the call to clk_set_parent() in
omap_dm_timer_init_one().
The function omap_hwmod_setup_one() will enable the timers functional clock
and therefore increment the use-count of the functional clock to 1.
clk_set_parent() will fail if the use-count is not 0 when called. Hence, if
omap_hwmod_setup_one() is called before clk_set_parent(), we will need to call
clk_disable() before calling clk_set_parent() to decrement the use-count.
Hence, avoid these extra calls to disable and enable the functional clock by
moving the calls to omap_hwmod_setup_one() and omap_hwmod_enable() to after
clk_set_parent().
We can also remove the delay from the __omap_dm_timer_set_source() function
because enabling the clock will now be handled via the HWMOD framework by
calling omap_hwmod_setup_one(). Therefore, by moving the calls to
omap_hwmod_setup_one() and omap_hwmod_enable() to after the call to
clk_set_parent(), we can simply replace __omap_dm_timer_set_source() with
clk_set_parent().
It should be safe to move these hwmod calls to later in the
omap_dm_timer_init_one() because other calls to the hwmod layer that occur
before are just requesting resource information.
Testing includes boot testing on OMAP2420 H4, OMAP3430 SDP and OMAP4430 Blaze
with the following configurations:
1. CONFIG_OMAP_32K_TIMER=y
2. CONFIG_OMAP_32K_TIMER=y and boot parameter "clocksource=gp_timer"
3. CONFIG_OMAP_32K_TIMER not set
4. CONFIG_OMAP_32K_TIMER not set and boot parameter "clocksource=gp_timer"
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Whenever we call the function omap_dm_timer_set_source() to set the clock
source of a dmtimer we look-up the dmtimer functional clock source by
calling clk_get(). This is not necessary because on requesting a dmtimer
we look-up the functional clock source and store it in the omap_dm_timer
structure. So instead of looking up the clock again used the clock handle
that stored in the omap_dm_timer structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The OMAP dmtimer driver does not currently have a function to disable the
timer interrupts. For some timer instances the timer interrupt enable
function can be used to disable the interrupts because the same interrupt
enable register is used to disable interrupts. However, some timer instances
have separate interrupt enable/disable registers and so this will not work.
Therefore, add a dedicated function to disable interrupts.
This change is required for OMAP4+ devices. For OMAP4, all timers apart from 1,
2 and 10 need this function and for OMAP5 all timers need this function.
Please note that the interrupt disable function has been written so that it
can be used by all OMAP devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The OMAP DMTIMERs can generate an interrupt when the timer counter value
matches the value stored in the timer's match register. When using this
feature spurious interrupts were seen, because the compare logic is being
enabled before the match value is loaded and according to the documentation
the match value must be loaded before the compare logic is enable.
The reset value for the timer counter and match registers is 0 and hence,
by enabling the compare logic before the actual match value is loaded a
spurious interrupt can be generated as the reset values match.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Restoring the timer interrupt status is not possible because writing a 1 to any
bit in the register clears that bit if set and writing a 0 has no affect.
Furthermore, if an interrupt is pending when someone attempts to disable a
timer, the timer will fail to transition to the idle state and hence it's
context will not be lost. Users should take care to service all interrupts
before disabling the timer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The timer TISTAT register is a read-only register and therefore restoring the
context is not needed. Furthermore, the context of TISTAT is never saved
anywhere in the current code. The TISTAT register is read-only for all OMAP
devices from OMAP1 to OMAP4. OMAP5 timers no longer have this register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
In commit e32f7ec2 (ARM: OMAP: Fix 32 kHz timer and modify GP timer to use GPT1)
a fix was added to prevent timer1 being reset in the function
omap_dm_timer_reset() because timer1 was being used as the system timer for
OMAP2 devices. Although timer1 is still used by most OMAP2+ devices as a system
timer, the function omap_dm_timer_reset() is now only being called for OMAP1
devices and OMAP1 does not use timer1 as a system timer. Therefore, remove the
check in omap_dm_timer_reset() so that timer1 is reset for OMAP1 devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Currently the dmtimer posted mode is being enabled when the function
omap_dm_timer_enable_posted() is called. This function is only being called
for OMAP1 timers and OMAP2+ timers that are being used as system timers. Hence,
for OMAP2+ timers that are NOT being used as a system timer, posted mode is
not enabled but the "timer->posted" variable is still set (incorrectly) in
the omap_dm_timer_prepare() function.
This is a regression introduced by commit 3392cdd3 (ARM: OMAP: dmtimer:
switch-over to platform device driver) which was before the
omap_dm_timer_enable_posted() function was introduced. Although this is a
regression from the original code it only impacts performance and so is not
needed for stable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Errata Titles:
i103: Delay needed to read some GP timer, WD timer and sync timer
registers after wakeup (OMAP3/4)
i767: Delay needed to read some GP timer registers after wakeup (OMAP5)
Description (i103/i767):
If a General Purpose Timer (GPTimer) is in posted mode
(TSICR [2].POSTED=1), due to internal resynchronizations, values read in
TCRR, TCAR1 and TCAR2 registers right after the timer interface clock
(L4) goes from stopped to active may not return the expected values. The
most common event leading to this situation occurs upon wake up from
idle.
GPTimer non-posted synchronization mode is not impacted by this
limitation.
Workarounds:
1). Disable posted mode
2). Use static dependency between timer clock domain and MPUSS clock
domain
3). Use no-idle mode when the timer is active
Workarounds #2 and #3 are not pratical from a power standpoint and so
workaround #1 has been implemented. Disabling posted mode adds some CPU
overhead for configuring and reading the timers as the CPU has to wait
for accesses to be re-synchronised within the timer. However, disabling
posted mode guarantees correct operation.
Please note that it is safe to use posted mode for timers if the counter
(TCRR) and capture (TCARx) registers will never be read. An example of
this is the clock-event system timer. This is used by the kernel to
schedule events however, the timers counter is never read and capture
registers are not used. Given that the kernel configures this timer
often yet never reads the counter register it is safe to enable posted
mode in this case. Hence, for the timer used for kernel clock-events,
posted mode is enabled by overriding the errata for devices that are
impacted by this defect.
For drivers using the timers that do not read the counter or capture
registers and wish to use posted mode, can override the errata and
enable posted mode by making the following function calls.
__omap_dm_timer_override_errata(timer, OMAP_TIMER_ERRATA_I103_I767);
__omap_dm_timer_enable_posted(timer);
Both dmtimers and watchdogs are impacted by this defect this patch only
implements the workaround for the dmtimer. Currently the watchdog driver
does not read the counter register and so no workaround is necessary.
Posted mode will be disabled for all OMAP2+ devices (including AM33xx)
using a GP timer as a clock-source timer to guarantee correct operation.
This is not necessary for OMAP24xx devices but the default clock-source
timer for OMAP24xx devices is the 32k-sync timer and not the GP timer
and so should not have any impact. This should be re-visited for future
devices if this errata is fixed.
Confirmed with Vaibhav Hiremath that this bug also impacts AM33xx
devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP2+ devices, when using DMTIMERs for system timers (clock-events and
clock-source) the posted mode configuration of the timers is used. To allow
the compiler to optimise the functions for configuring and reading the system
timers, the posted flag variable is hard-coded with the value 1. To make it
clear that posted mode is being used add some definitions so that it is more
readable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5hx
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91 into next/headers
From Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
arm: at91: mach header cleanup
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
* tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91:
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The debug-leds driver should not rely on hard coded macro for
the iomem size but use the resource size instead.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/mach-omap2/prcm.c and arch/arm/plat-omap/include/plat/prcm.h
are now completely unused and can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Split omap2_set_globals_prcm() into PRM, CM, and PRCM_MPU variants, since
these are all separate IP blocks. This should make it easier to move the
PRM, CM, PRCM_MPU code into drivers/ in future patchsets.
At this point arch/arm/plat-omap/include/plat/prcm.h is empty; a
subsequent patch will remove it, and remove the #include from all the
files that #include it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Now that all users of mach-omap2/omap2_cm_wait_idlest() have been removed,
delete the function and its supporting macros and prototypes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Get rid of the mach-omap2/common.c globals by moving the global
initialization for IP block addresses that must occur early into
mach-omap2/io.c. In the process, remove the *_map_common_io*() and
SoC-specific *set_globals* functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
omap_prcm_get_reset_sources() is now unused; so, remove it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
The only thing omap_init_consistent_dma_size() does is increase the
consistent DMA size if CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE is defined.
Increasing the consistent DMA size should no longer be needed with CMA
in place.
This patch removes omap_init_consistent_dma_size() and also
arch/arm/mach-omap2/io.c:omap_common_init_early() which becomes an empty
function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: updated for moved dma.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
struct uart_omap_port and struct uart_omap_dma, and associated
definitions are private to the driver, so there's no point them sitting
in an include file under arch/arm. Move them into the driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now mach/hardware.h is empty for omap2+ and can be
removed except for plat-omap/dmtimer.c for omap1.
Also the include of mach/irqs.h can now be removed
for shared plat-omap/i2c.c as it's no longer needed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to add device-tree support to the timer driver the following changes
were made ...
1. Allocate system timers (used for clock-events and clock-source) based upon
timer properties rather than using an hard-coded timer instance ID. To allow
this a new helper function called omap_dmtimer_find_by_property() has been
added for finding a timer with the particular properties in the device-tree
blob. Please note that this is an internal helper function for system timers
only to find a timer in the device-tree blob. This cannot be used by device
drivers, another API has been added for that (see below). Timers that are
allocated for system timers are dynamically disabled at boot time by adding
a status property with the value "disabled" to the timer's device-tree node.
Please note that when allocating system timers we now pass a timer ID and
timer property. The timer ID is only be used for allocating a timer when
booting without device-tree. Once device-tree migration is complete, all
the timer ID references will be removed.
2. System timer resources (memory and interrupts) are directly obtained from
the device-tree timer node when booting with device-tree, so that system
timers are no longer reliant upon the OMAP HWMOD framework to provide these
resources.
3. If DT blob is present, then let device-tree create the timer devices
dynamically.
4. When device-tree is present the "id" field in the platform_device structure
(pdev->id) is initialised to -1 and hence cannot be used to identify a timer
instance. Due to this the following changes were made ...
a). The API omap_dm_timer_request_specific() is not supported when using
device-tree, because it uses the device ID to request a specific timer.
This function will return an error if called when device-tree is present.
Users of this API should use omap_dm_timer_request_by_cap() instead.
b). When removing the DMTIMER driver, the timer "id" was used to identify the
timer instance. The remove function has been modified to use the device
name instead of the "id".
5. When device-tree is present the platform_data structure will be NULL and so
check for this.
6. The OMAP timer device tree binding has the following optional parameters ...
a). ti,timer-alwon --> Timer is in an always-on power domain
b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP
c). ti,timer-pwm --> Timer can generate a PWM output
d). ti,timer-secure --> Timer is reserved on a secure OMAP device
Search for the above parameters and set the appropriate timer attribute
flags.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Currently OMAP timers can be requested by requesting any available or by a
numerical device ID. If a specific timer is required because it has a particular
capability, such as can interrupt the on-chip DSP in addition to the ARM CPU,
then the user needs to know the device ID of the timer with this feature.
Therefore, add a new API called omap_dm_timer_request_by_cap() that allows
drivers to request a timer by capability.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* code:
http://www.spinics.net/lists/linux-omap/msg80520.html
Fix includes for fpga.h by making fpga.h local
to mach-omap1. The common code in plat-omap just
needs to know the struct h2p2_dbg_fpga, which can
be local to debug-leds.c.
This also fixes the braindead <../*.h> style includes
that got accidentally added with search and replace
during the cleanup.
Signed-off-by: Tony Lindgren <tony@atomide.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* code:
http://www.spinics.net/lists/linux-omap/msg80520.html
Note that eventually when the omap1 specific drivers
are fixed to not use cpu_is_omap macros and not depend
on mach/hardware.h, this patch can be reverted and these
headers can be local. But since just fixing the drivers for
omap2+ is already a big enough hassle, let's deal
with that properly first.
[tony@atomide.com: also drop unused include for ispvideo.c]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This code will be eventually in drivers, and for the
code in the drivers we don't want to have any cpu_is_omap
usage. Those macros should be private to arch/arm/mach-omap1
and arch/arm/mach-omap2.
To fix this, let's move the define for dma_omap2plus()
to dma-omap.h, and use the existing dma_attr passed in
the platform_data as the revision registers are what they
are.
Note that we can now also remove the relative includes
introduced by the recent clean-up patches.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
Let's add plat/debug-devices.h for debug_card_init()
to fix the relative includes.
Note that drivers must not use this header as it will
break build for omap2+ CONFIG_MULTIPLATFORM builds.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the prototypes in plat-omap/common.h are not
common to omap1 and omap2+, they are local to omap2+
and should not be in plat-omap/common.h.
The only shared function prototype in this file is
omap_init_clocksource_32k(), let's put that into
counter-32k.h.
Note that the new plat/counter-32k.h must not be
included from drivers, that will break omap2+ build
for CONFIG_MULTIPLATFORM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This code should be private to mach-omap2.
The only use for it in for omap1 has been in dmtimer.c
to check for context loss. However, omap1 does not
lose context during idle, so the code is not needed.
Further, omap1 timer has OMAP_TIMER_ALWON set, so omap1
was not hitting omap_pm_get_dev_context_loss_count()
test.
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
To fix this for the shared i2c.h, let's re-introduce
a minimal plat/i2c.h.
Note that drivers must not use this header as it will
break build for omap2+ CONFIG_MULTIPLATFORM builds.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The common code should not have any omap1 or omap2+
specific code, and should not need to call the cpu_is_omap
macros.
The only remaining user for cpu_is_omap macros is
omap_i2c_nr_ports(). Let's make those checks in
the omap specific implementation of omap_i2c_add_bus()
instead in order to remove cpu_is_omap usage from
the common code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's make the omap2+ specific parts private to mach-omap2.
This leaves just a minimal shared code into plat-omap like
it should be.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the defines are specific to omap1 and omap2+,
and should be in the local headers. Only minimal function
prototypes need to be shared.
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
So this patch re-adds a minimal plat/sram.h.
The new plat/sram.h must not be included from drivers,
that will break build for omap2+ CONFIG_MULTIPLATFORM.
Note that this patch temporarily adds two more
relative includes; Those will be removed in the
following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add HWMOD_EXT_OPT_MAIN_CLK flag to indicate that this IP block is
dependent on an off-chip functional clock that is not guaranteed to be
present during initialization. IP blocks marked with this flag are
left in the INITIALIZED state during kernel init.
This is a workaround for a hardware problem. It should be possible to
guarantee that at least one clock source will be present and active
for any IP block's main functional clock. This ensures that the hwmod
code can enable and reset the IP block. Resetting the IP block during
kernel init prevents any bogus bootloader, ROM code, or previous OS
configuration from affecting the kernel. Hopefully a clock
multiplexer can be added on future SoCs.
N.B., at some point in the future, it should be possible to query the
clock framework for this type of information. Then this flag should
no longer be needed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we
had a few of these patches cause regressions themselves and had to
work out how to deal with those in the meantime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IDdm
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we had a
few of these patches cause regressions themselves and had to work out
how to deal with those in the meantime."
* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
Revert "ARM i.MX25: Fix PWM per clock lookups"
ARM: versatile: fix versatile_defconfig
ARM: mvebu: update defconfig with 3.7 changes
ARM: at91: fix at91x40 build
ARM: socfpga: Fix socfpga compilation with early_printk() enabled
ARM: SPEAr: Remove unused empty files
MAINTAINERS: Add arm-soc tree entry
ARM: dts: mxs: add the "clock-names" for gpmi-nand
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
...
In order to make single zImage work for ARM architecture,
we need to make sure we don't depend on private headers.
Move USB platform_data to <linux/platform_data/omap-usb.h>
and add a minimal drivers/mfd/usb-omap.h.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for local mfd/usb-omap.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's move what we can from plat/usb.h to the local usb.h
for ARM common zImage support.
This is needed so we can remove plat/usb.h for ARM common
zImage support.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For omap1, we'll keep mach/serial.h around for 8250.c hardware
workarounds. For omap2+, we no longer need mach/serial.h and
can make it local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to eventually move omap2+ to generic
debug code that's configured in Kconfig for the port.
Signed-off-by: Tony Lindgren <tony@atomide.com>
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HUTj
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-signed' into omap-for-v3.8/cleanup-headers-serial-take2
This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
This reverts commit 957ee7270d
(serial: omap: fix software flow control).
As Russell has pointed out, that commit isn't fixing
Software Flow Control at all, and it actually makes
it even more broken.
It was agreed to revert this commit and use Russell's
latest UART patches instead.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows us to get rid of the ifdefs in 8250.c.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8f31cefe (ARM: OMAP2+: select PINCTRL in Kconfig)
added select PINCTRL, but accdentally added it to a wrong
location.
We want to select if for ARCH_OMAP2PLUS, not for
ARCH_OMAP2PLUS_TYPICAL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.
Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.
This is needed for the ARM common zImage support.
[tony@atomide.com: updated to not print a warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
To facilitate the ARM single image work, split
arch/arm/plat-omap/include/plat/clkdev_omap.h into the
arch/arm/mach-omap1/clock.h and arch/arm/mach-omap2/clock.h files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove arch/arm/plat-omap/include/plat/clock.h by merging it into
arch/arm/mach-omap1/clock.h and arch/arm/mach-omap2/clock.h.
The goal here is to facilitate ARM single image kernels by removing
includes via the "plat/" symlink.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: fixed to remove duplicate clock.h includes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Duplicate arch/arm/plat-omap/clock.c into arch/arm/mach-omap1/clock.c
and arch/arm/mach-omap2/clock.c. This is to support people who are working
on the ARM single image kernel and the OMAP common clock framework
conversion.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Moving plat/omap-secure.h locally to mach-omap2/
as part of single zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_reserve() callback is defned only for mach-omap2.
So, moving definition of omap_reserve() to mach-omap2.
This helps is moving plat/omap_secure.h local to
mach-omap2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must move this for ARM common zImage support.
Note that neither drivers/media/rc/ir-rx51.c or
drivers/media/platform/omap3isp/ispvideo.c need
to include omap-pm.h, so this patch removes the
include for those files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: linux-media@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is private to cpu.h and no other places should
need to include it and we can drop the include
in mach-omap2/io.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to keep the device related things in the
common i2c.c as omap2+ is using hwmod. Split the code to
mach-omap1 and mach-omap2 parts and only leave common
code to plat-omap/i2c.c.
Note that as omap1 only has one i2c controller, we can
now remove the old device related macros.
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We cannot keep this in plat as it causes problems
with the ARM single zImage support.
Cc: Felipe Balbi <balbi@ti.com>
Cc: linux-pcmcia@lists.infradead.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to have this file in plat/fpga.h. We can
make it local to plat-omap replacing fpga_read/write
functions directly with readb/writeb as that's how
they are already defined in fpga.h.
Note that 2420 based H4 is also using the fpga, so let's
keep the led support around in plat-omap until we flip
over mach-omap2 to device tree.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove arch/arm/plat-omap/include/plat/sdrc.h by folding its contents
into arch/arm/mach-omap2/sdrc.h. The objective is to assist Tony in
cleaning out arch/arm/plat-omap/, as his upstreams request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[tony@atomide.com: updated to remove rotate macros]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that VRFB driver handles its registers independently, we can remove
the VRFB related code from OMAP's sdrc.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
