* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
Fixes the following:
1. POLL should not enable IRQ when work is not completed
2. No locking between TX descriptor cleaning and XMIT descriptor handling
3. No locking between RX POLL and XMIT modifying control register
4. Since TX cleaning (called from POLL) is running in parallel with XMIT
unnecessary locking is needed.
5. IRQ handler looks at RX frame status solely, this is wrong when IRQ is
temporarily disabled (in POLL), and when IRQ is shared.
6. IRQ handler clears IRQ status, which is unnecessary
7. TX queue was stopped in preventing cause when not MAX_SKB_FRAGS+1
descriptors were available after a SKB been scheduled by XMIT. Instead
the TX queue is stopped first when not enough descriptors are available
upon entering XMIT.
It was hard to split up this patch in smaller pieces since all are tied
together somehow.
Note the RX flag used in the interrupt handler does not signal that
interrupt was asserted, but that a frame was received. Same goes for TX.
Also, IRQ is not asserted when the RX flag is set before enabling IRQ
enable until a new frame is received. So extra care must be taken to
avoid enabling IRQ and all descriptors are already used, hence dead lock
will upon us. See new POLL implementation that enableds IRQ then look at
the RX flag to determine if one or more IRQs may have been missed. TX/RX
flags are cleared before handling previously enabled descriptors, this
ensures that the RX/TX flags are valid when determining if IRQ should be
turned on again.
By moving TX cleaning from POLL to XMIT in the standard case, removes some
locking trouble. Enabling TX cleaning from poll only when not enough TX
descriptors are available is safe because the TX queue is at the same time
stopped, thus XMIT will not be called. The TX queue is woken up again when
enough descriptrs are available.
TX Frames are always enabled with IRQ, however the TX IRQ Enable flag will
not be enabled until XMIT must wait for free descriptors.
Locking RX and XMIT parts of the driver from each other is needed because
the RX/TX enable bits share the same register.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frame error interrupts must also be handled since the RX flag only indicates
successful reception, it is unlikely but the old code may lead to dead lock
if 128 error frames are recieved in a row.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new SKB buffer should not be allocated when the old SKB is reused.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is safe to enable all fragments before enabling the first descriptor,
this way all descriptors don't have to be processed twice, added extra
memory barrier.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NAPI is disabled there is no point in having IRQs enabled, TX/RX
should be off before clearing the TX/RX descriptor rings.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, not all CONFIG_OF platforms provide
pci_device_to_OF_node().
Change the test to CONFIG_SPARC for now to deal with
the build regressions.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915/lvds: Add AOpen i915GMm-HFS to the list of false-positive LVDS
agp/intel: Fix device names of i845 and 845G
drm/i915: Disable GPU semaphores on SandyBridge mobile
drm/i915/execbuffer: Clear domains before beginning reloc processing
drm/i915/execbuffer: Reorder relocations to match new object order
drm/i915: Fix error handler to capture the first batch after the seqno
drm/i915: Add a module option to override the use of SSC
drm/i915/panel: The backlight is enabled if the current value is non-zero
drm/i915/debugfs: Correct format after changing type of err object 'size'
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
* git://git.infradead.org/battery-2.6: (21 commits)
power_supply: Add MAX17042 Fuel Gauge Driver
olpc_battery: Fix up XO-1.5 properties list
olpc_battery: Add support for CURRENT_NOW and VOLTAGE_NOW
olpc_battery: Add support for CHARGE_NOW
olpc_battery: Add support for CHARGE_FULL_DESIGN
olpc_battery: Ambient temperature is not available on XO-1.5
jz4740-battery: Should include linux/io.h
s3c_adc_battery: Add gpio_inverted field to pdata
power_supply: Don't use flush_scheduled_work()
power_supply: Fix use after free and memory leak
gpio-charger: Fix potential race between irq handler and probe/remove
gpio-charger: Provide default name for the power_supply
gpio-charger: Check result of kzalloc
jz4740-battery: Check if platform_data is supplied
isp1704_charger: Detect charger after probe
isp1704_charger: Set isp->dev before anything needs it
isp1704_charger: Detect HUB/Host chargers
isp1704_charger: Correct length for storing model
power_supply: Add gpio charger driver
jz4740-battery: Protect against concurrent battery readings
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
mfd: ab8500-core chip version cut 2.0 support
mfd: Flag WM831x /IRQ as a wake source
mfd: Convert WM831x away from legacy I2C PM operations
regulator: Support MAX8998/LP3974 DVS-GPIO
mfd: Support LP3974 RTC
i2c: Convert SCx200 driver from using raw PCI to platform device
x86: OLPC: convert olpc-xo1 driver from pci device to platform device
mfd: MAX8998/LP3974 hibernation support
mfd/ab8500: remove spi support
mfd: Remove ARCH_U8500 dependency from AB8500
misc: Make AB8500_PWM driver depend on U8500 due to PWM breakage
mfd: Add __devexit annotation for vx855_remove
mfd: twl6030 irq_data conversion.
gpio: Fix cs5535 printk warnings
misc: Fix cs5535 printk warnings
mfd: Convert Wolfson MFD drivers to use irq_data accessor function
mfd: Convert TWL4030 to new irq_ APIs
mfd: Convert tps6586x driver to new irq_ API
mfd: Convert tc6393xb driver to new irq_ APIs
mfd: Convert t7166xb driver to new irq_ API
...
Make wakeup events be reported by the PCI subsystem before attempting to
resume devices or queuing up runtime resume requests for them, because
wakeup events should be reported as soon as they have been detected.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After recent changes related to wakeup events pm_wakeup_event()
automatically checks if the given device is configured to signal wakeup,
so pci_wakeup_event() may be a static inline function calling
pm_wakeup_event() directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI sysfs ROM interface requires an enabling write to access the ROM
image, but the default file mode is 0400. The original proposed patch
adding sysfs ROM support was a true read-only interface, with the
enabling bit coming in as a feature request. I suspect it was simply an
oversight that the file mode didn't get updated to match the API.
Acked-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the evaluation of acpi_pci_osc_control_set() (to request control of
PCI Express native features) into acpi_pci_root_add() to avoid calling
it many times for the same root complex with the same arguments.
Additionally, check if all of the requisite _OSC support bits are set
before calling acpi_pci_osc_control_set() for a given root complex.
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-by: Ozan Caglayan <ozan@pardus.org.tr>
Tested-by: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
They got mixed up when the switch was converted to a table in 2007.
Signed-off-by: Oswald Buddenhagen <ossi@kde.org>
[ickle: minor changes for 2.6.37+]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit a1f5f22adc ("gpio: timbgpio:
irq_data conversion") was slightly too enthusiastic in converting
timbgpio_irq() over to take an irq_data * argument instead of an
unsigned int irq argument, as it is a flow handler, which still take
IRQ numbers for now. (And on top of that, it was using the wrong
accessors.)
This fixes it up, and seems to build without warnings.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MAX17042 is a fuel gauge with an I2C interface for lithium-ion
betteries. Unlike its predecessor MAX17040, MAX17042 uses 16bit
registers. Besides, MAX17042 has much more features than MAX17040; e.g.,
a thermistor, current and current accumulation measurement, battery
internal resistance estimate, average values of measurement, and others.
This patch implements a driver for MAX17042.
In this initial release, we have implemented the most basic features of
a fuel gauge: measure the battery capacity and voltage.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch adds support for chip version 2.0 or cut 2.0.
One new interrupt latch register - latch 12 - is introduced.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x can generate wake events, some unconditionally, so flag
the primary IRQ as a wake source in order to help the CPU treat the
/IRQ signal appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the legacy bus PM operations are deprecated move the suspend
method over to dev_pm_ops.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The previous driver did not support BUCK1-DVS3, BUCK1-DVS4, and
BUCK2-DVS2 modes. This patch adds such modes and an option to block
setting buck1/2 voltages out of the preset values.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The first releases of LP3974 have a large delay in RTC registers,
which requires 2 seconds of delay after writing to a rtc register
(recommended by National Semiconductor's engineers)
before reading it.
If "rtc_delay" field of the platform data is true, the rtc driver
assumes that such delays are required. Although we have not seen
LP3974s without requiring such delays, we assume that such LP3974s
will be released soon (or they have done so already) and they are
supported by "lp3974" without setting "rtc_delay" at the platform
data.
This patch adds delays with msleep when writing values to RTC registers
if the platform data has rtc_delay set.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The SCx200 ACB driver supports ISA hardware as well as PCI. The PCI
hardware is CS5535/CS5536 based, and the device that it grabs is handled by
the cs5535-mfd driver. This converts the SCx200 driver to use a
platform_driver rather than the previous PCI hackery.
The driver used to manually track the iface list (via linked list); now it
only does this for ISA devices. PCI ifaces are handled through standard
driver model lists.
It's unclear what happens in case of errors in the old ISA code; rather than
pretending the code actually cares, I've dropped the (implicit) ignorance
of return values and marked it with a comment.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the driver to save and restore register values
for hibernation.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the Ab8500 v1.0, the SPI support is deprecated on the HW.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
While it is vanishingly unlikely that the device will be deployed on other
architectures removing the dependency facilitates build testing when doing
generic work on both the MFD core for the device and the subsystem drivers.
There appears to be no actual code dependency.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since we don't have a PWM API every PWM driver ends up exporting its
own version and we need to limit the platforms we try to build them on
in order to avoid multiple definitions. As the AB8500 is normally a
companion chip for the U8500 CPU depend on that architecture.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
drivers/gpio/cs5535-gpio.c: In function 'cs5535_gpio_probe':
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Use vsprintf extension %pR to format resource.
Original-patch-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
drivers/misc/cs5535-mfgpt.c: In function 'cs5535_mfgpt_probe':
drivers/misc/cs5535-mfgpt.c:320: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/misc/cs5535-mfgpt.c:320: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Use vsprintf extension %pR to format resource.
Original-patch-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Actually makes the code larger rathe rthan smaller but does provide some
isolation against core API changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data to irq_chip
operations. Update the TWL4030 driver to the new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to supply struct irq_data to irq_chip
operations rather than an irq number. Update the tps6586x driver to the
new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being update to pass struct irq_data to irq_chip rather
than an irq number to operations. Update tc6393 to the new API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data rather than an
irq number to irq_chip operations. Update the t7166xb driver to the new
APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to supply struct irq_data to irq_chip
operations rather than an irq number. Update the SMTPE driver to the new
APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data to interrupt
operations, update the MAX8998 driver to the new API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq infrastructure is being converted to pass struct irq_data rather
than an irq number to irq_chip operations, update max8925 to the new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert the jz4740-adc driver to use the recently introduced IRQ API
variants which are passed struct irq_data rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being converted to pass a struct irq_data to interrupt
operations rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being converted to pass a struct irq_data to interrupt
operations rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
