With the introduction of an AMBA PrimeCell per-cell block clock,
the pclk was left on after probe() unless explicitly disabled.
This clock is wired to the same clock on PL022 causing it to stay
always on since.
Fix this up properly by clocking the pclk whenever we want to
write into any PL022 registers and clocking the external clock
whenever we want to transmit messages on the bus.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by : Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When using PIO we have a timeout for the TX and RX FIFOs to ensure that
the data actually gets transferred. Warn if we hit that timeout - it
should never happen, but this makes sure we'll find out if it does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Try to handle unknown nmis with an enabled PMU
perf, x86: Fix handle_irq return values
perf, x86: Fix accidentally ack'ing a second event on intel perf counter
oprofile, x86: fix init_sysfs() function stub
lockup_detector: Sync touch_*_watchdog back to old semantics
tracing: Fix a race in function profile
oprofile, x86: fix init_sysfs error handling
perf_events: Fix time tracking for events with pid != -1 and cpu != -1
perf: Initialize callchains roots's childen hits
oprofile: fix crash when accessing freed task structs
Instead of, wrongly, reusing the 'val' variable, use a dedicated
one for reading the status register.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix compilation warning by typecasting the tx_buf pointer.
[I'm not thrilled with resorting to a cast; but I cannot see a better
way to go about this. I don't want to drop the const from struct
spi_transfer ~~glikely]
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 052dc7c45i "spi/dw_spi: conditional transfer mode change"
introduced cs_control code, which has a bug by using bit offset
for spi mode to set transfer mode in control register. Also it
forces devices who don't need cs_control to re-configure the
control registers for each spi transfer. This patch will fix them
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow interrupt sharing since exclusive interrupt line for
DW SPI controller is not provided on every platform.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For small transfers at high speeds the expected transfer time can easily
be well under 1ms, causing the delay in wait_for_xfer() to be only the
dead reckoning fudge factor of 5ms currently included. Experiments on
some of my systems shows that this is marginal for some transfers so
double it to 10ms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow the use of the S3C64xx SPI controller with things like PMICs by
moving the init up to subsys_initcall().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device is handled by hid-mosart driver, and therefore should
be present in hid_blacklist[], not hid_ignore_list[].
Cc: Stephane Chatty <chatty@lii-enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The following patch instructs usbhid/hid-mosart to handle a new multitouch
controller, built-in by some Asus EeePC T101MT models.
Signed-off-by: Roland Baum <rba@tr33.de>
Tested-by: Roland Baum <rba@tr33.de>
Acked-by: Stéphane Chatty <chatty@enac.fr>
CC: Stéphane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The missing break statement causes wrong capacity calculation for
batteries that report energy.
Reported-by: d binderman <dcb314@hotmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This reverts commit b9421ae8f3.
This warning was so prelevant, even for apparently working machines,
that it was just causing fear, anxiety and panic.
The root cause still remains, so we will add some better debugging when
we focus on fixing it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=17021
Reported-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 0f3ee801b3.
Enabling LVDS on pipe A was causing excessive wakeups on otherwise idle
systems due to i915 interrupts. So restrict the LVDS to pipe B once more,
whilst the issue is properly diagnosed.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16307
Reported-and-tested-by: Enrico Bandiello <enban@postal.uv.es>
Poked-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Adam Jackson <ajax@redhat.com>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
* 'for-linus' of git://neil.brown.name/md:
md: resolve confusion of MD_CHANGE_CLEAN
md: don't clear MD_CHANGE_CLEAN in md_update_sb() for external arrays
Move .gitignore from drivers/md to lib/raid6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
pkt_sched: Fix lockdep warning on est_tree_lock in gen_estimator
ipvs: avoid oops for passive FTP
Revert "sky2: don't do GRO on second port"
gro: fix different skb headrooms
bridge: Clear INET control block of SKBs passed into ip_fragment().
3c59x: Remove incorrect locking; correct documented lock hierarchy
sky2: don't do GRO on second port
ipv4: minor fix about RPF in help of Kconfig
xfrm_user: avoid a warning with some compiler
net/sched/sch_hfsc.c: initialize parent's cl_cfmin properly in init_vf()
pxa168_eth: fix a mdiobus leak
net sched: fix kernel leak in act_police
vhost: stop worker only if created
MAINTAINERS: Add ehea driver as Supported
ath9k_hw: fix parsing of HT40 5 GHz CTLs
ath9k_hw: Fix EEPROM uncompress block reading on AR9003
wireless: register wiphy rfkill w/o holding cfg80211_mutex
netlink: Make NETLINK_USERSOCK work again.
irda: Correctly clean up self->ias_obj on irda_bind() failure.
wireless extensions: fix kernel heap content leak
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: wlan-ng: Explicitly set some fields in cfg80211 interface
Staging: octeon: depends on NETDEVICES
Staging: spectra: depend on X86_MRST
Staging: zram: free device memory when init fails
Staging: rt2870sta: Add more device IDs from vendor drivers
staging: comedi das08_cs.c: Fix io_req_t conversion
staging: spectra needs <linux/slab.h>
staging: hv: Fixed lockup problem with bounce_buffer scatter list
staging: hv: Increased storvsc ringbuffer and max_io_requests
staging: hv: Fixed the value of the 64bit-hole inside ring buffer
staging: hv: Fixed bounce kmap problem by using correct index
staging: hv: Fix missing functions for net_device_ops
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ftdi_sio: Added custom PIDs for ChamSys products
USB: cdc-acm: Fixing crash when ACM probing interfaces with no endpoint descriptors.
USB: cdc-acm: Add pseudo modem without AT command capabilities
USB: cxacru: Use a bulk/int URB to access the command endpoint
usb: serial: mos7840: Add USB IDs to support more B&B USB/RS485 converters.
USB: cdc-acm: Adding second ACM channel support for various Nokia and one Samsung phones
usb: serial: mos7840: Add USB ID to support the B&B Electronics USOPTL4-2P.
USB: ssu100: turn off debug flag
usb: allow drivers to use allocated bandwidth until unbound
USB: cp210x usb driver: add USB_DEVICE for Pirelli DP-L10 mobile.
USB: cp210x: Add B&G H3000 link cable ID
USB: CP210x Add new device ID
USB: option: fix incorrect novatel entries
USB: Fix kernel oops with g_ether and Windows
USB: rndis: section mismatch fix
USB: ehci-ppc-of: problems in unwind
USB: s3c-hsotg: Remove DEBUG define
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix tty_line must not be equal to number of allocated tty pointers in tty driver
serial: bfin_sport_uart: restore transmit frame sync fix
serial: fix port type conflict between NS16550A & U6_16550A
MAINTAINERS: orphan isicom
vt: Fix console corruption on driver hand-over.
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not oops when erroneous PEB is scheduled for scrubbing
UBI: fix kconfig unmet dependency
UBI: fix forward compatibility
UBI: eliminate update of list_for_each_entry loop cursor
* 'drm-intel-fixes' of git://anongit.freedesktop.org/~ickle/drm-intel: (25 commits)
intel_agp,i915: Add more sandybridge graphics device ids
drm/i915: Enable MI_FLUSH on Sandybridge
agp/intel: Fix cache control for Sandybridge
agp/intel: use #ifdef idiom for intel-agp.h
agp/intel: fix physical address mask bits for sandybridge
drm/i915: Prevent double dpms on
drm/i915: Avoid use of uninitialised values when disabling panel-fitter
drm/i915: Avoid pageflipping freeze when we miss the flip prepare interrupt
drm/i915: Tightly scope intel_encoder to prevent invalid use
drm/i915: Allocate the PCI resource for the MCHBAR
drm/i915/dp: Really try 5 times before giving up.
drm/i915/sdvo: Restore guess of the DDC bus in absence of VBIOS
drm/i915/dp: Boost timeout for enabling transcoder to 100ms
drm/i915: Re-use set_base_atomic to share setting of the display registers
drm/i915: Fix offset page-flips on i965+
drm/i915: Include a generation number in the device info
i915: return -EFAULT if copy_to_user fails
i915: return -EFAULT if copy_to_user fails
agp/intel: Promote warning about failure to setup flush to error.
drm/i915: overlay on gen2 can't address above 1G
...
It causes all kinds of DMA API debugging assertions and
all straight-forward attempts to fix it have failed.
So turn off SG, and we'll tackle making this work
properly in net-next-2.6
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a simplified version of the original patch from James Courtier-Dutton.
>From: James Courtier-Dutton
>Subject: [PATCH] Fix b44 RX FIFO overflow recovery.
>Date: Wednesday, June 30, 2010 - 1:11 pm
>
>This patch improves the recovery after a RX FIFO overflow on the b44
>Ethernet NIC.
>Before it would do a complete chip reset, resulting is loss of link
>for a few seconds.
>This patch improves this to do recovery in about 20ms without loss of link.
>
>Signed off by: James@superbug.co.uk
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug introduced in commit
de84727214
"3c59x: Use fine-grained locks for MII and windowed register access".
vortex_interrupt() holds vp->window_lock over multiple register
accesses to reduce locking overhead. However it also needs to call
vortex_error() sometimes, and that uses the regular functions for
access to windowed registers, which will try to acquire window_lock
again.
Therefore, drop window_lock around the call to vortex_error() and set
the window afterward reacquiring the lock. Since vortex_error() may
call vortex_rx(), which *does* require its caller to hold window_lock,
lift that call up into vortex_interrupt(). This also removes the
potential for calling vortex_rx() on a later-generation NIC.
Reported-and-tested-by: Jens Schüßler <jgs@trash.net> [in Debian's 2.6.32]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time_before_eq()/time_after_eq() functions operate on unsigned
long and only work if the difference between the two compared values
is smaller than half the range of unsigned long (31 bits on i386).
Some of the variables (slave->jiffies, dev->trans_start, dev->last_rx)
used by bonding store a copy of jiffies and may not be updated for a
long time. With HZ=1000, time_before_eq()/time_after_eq() will start
giving bad results after ~25 days.
jiffies will never be before slave->jiffies, dev->trans_start,
dev->last_rx by more than possibly a couple ticks caused by preemption
of this code. This allows us to detect/prevent these overflows by
replacing time_before_eq()/time_after_eq() with time_in_range().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot use spinlock when kmalloc is invoked with
GFP_KERNEL flag because it can sleep.
So this patch reviews the usage of spinlock within the
stmmac_resume function avoing this bug.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ce17178094.
This commit has been independently bisected a few times as being the cause
of a s2ram failure.
Reported-and-tested-by: Kyle McMartin <kyle@mcmartin.ca>
Reported-and-tested-by: Andy Isaacson <adi@hexapodia.org>
Cc: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 409f3499a2 (scsi/sd: remove big
kernel lock) introduced a bug in the sd_release routine. Medium
removal should be allowed when the number of open file references
drops to 0, not when it becomes non-zero.
This patch (as1414) adjusts the test to fix the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
New pci ids for GT2 and GT2+ on desktop and mobile sandybridge,
and graphics device ids for server sandybridge. Also rename original
ids string to reflect GT1 version.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
MI_FLUSH is being deprecated, but still available on Sandybridge.
Make sure it's enabled as userspace still uses MI_FLUSH.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Sandybridge GTT has new cache control bits in PTE, which controls
graphics page cache in LLC or LLC/MLC, so we need to extend the mask
function to respect the new bits.
And set cache control to always LLC only by default on Gen6.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It should shift bit 39-32 into pte's bit 11-4.
Reported-by:Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Arguably this is a bug in drm-core in that we should not be called twice
in succession with DPMS_ON, however this is still occuring and we see
FDI link training failures on the second call leading to the occassional
blank display. For the time being ignore the repeated call.
Original patch by Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
We were passing garbage values into the panel-fitter control register
when disabling it on Ironlake - those values (filter modes and reserved
MBZ bits) would have then be re-used the next time panel-fitting was
enabled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When we miss the flip prepare interrupt, we never get into the
software state needed to restart userspace, resulting in a freeze of a
full-screen OpenGL application (such as a compositor).
Work around this by checking DSPxSURF/DSPxBASE to see if the page flip
has actually happened. If it has, do the work we would have done when
the flip prepare interrupt comes in.
Also, add debugfs information to tell us what's going on (based on the
patch from Chris Wilson attached to bugs.fdo bug #29798).
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We reset intel_encoder for every matching encoder whilst iterating over
the encoders attached to this crtc when changing mode. As such in a
cloned configuration intel_encoder may not correspond to the correct
is_edp encoder.
By scoping intel_encoder to the loop, not only is the compiler able to
spot this mistake, we also improve readiability for ourselves.
[It might not be a mistake, within this function it is unclear as to
whether it is permissable for eDP to be cloned...]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were failing when trying to allocate the resource for MMIO of the
MCHBAR because we forgot to specify what type of resource we wanted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Only stop trying if the aux channel sucessfully reports that the
transmission was completed, otherwise try again. On the 5th failure,
bail and report that something is amiss.
This fixes a sporadic failure in reading the EDID for my external panel
over DP.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
If the VBIOS tells us the mapping of the SDVO device onto the DDC bus,
use it. However, if there is no VBIOS available that mapping is
uninitialised and we should fallback to our earlier guess.
Fix regression introduced in b1083333 (which in turn is a fix for the
regression caused by the introduction of this guess, 14571b4).
References:
Bug 29499 - [945GM] Screen disconnected because of missing VBIOS
https://bugs.freedesktop.org/show_bug.cgi?id=29499
Bug 15109 - i945GM fails to detect EDID on DVI port
https://bugzilla.kernel.org/show_bug.cgi?id=15109
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Adam Hill reported that his Arrandale system required a much longer, up
to 200x500us, wait for the panel to initialise or else modesetting would
fail.
References:
https://bugs.freedesktop.org/show_bug.cgi?id=29141
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Adam Hill <sidepipeuk@yahoo.co.uk>
i965 uses the Display Registers to compute the offset from the display
base so the new base does not need adjusting when flipping. The older
chipsets use a fence to access the display and so do perceive the
surface as linear and have a single base register which is reprogrammed
using the flip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: Marty Jack <martyj19@comcast.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
copy_to_user() returns the number of bytes remaining to be copied and
I'm pretty sure we want to return a negative error code here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
copy_to_user returns the number of bytes remaining to be copied, but we
want to return a negative error code here. These are returned to
userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Make sure we always detect when we fail to correctly allocate the Isoch
Flush Page and print an error to warn the user about the likely memory
corruption that will result in invalid rendering or worse.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
So set the coherent dma mask accordingly. This dma mask is only used
for physical objects, so it won't really matter allocation-wise.
Now this never really surfaced because sane 32bit kernels only have 1G
of lowmem. But some eager testers (distros?) still carry around the patch
to adjust lowmem via a kconfig option. And the kernel seems to favour
high allocations on boot-up, hence the overlay blowing up reliably.
Because the patch is tiny and nicely shows how broken gen2 is it's imho
worth to merge despite the fact that mucking around with the lowmem/
highmem division is (no longer) supported.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28318
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The vblank status bit is a sticky bit that must be cleared with a write
of '1' prior to polling for the next vblank.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
jbarnes: I'd still rather see a lock, but I think you're right that
we don't generally wait in code that needs not to miss an interrupt.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Partial revert of 9d0498a2bf.
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Tested-by: Hugh Dickins <hughd@google.com>
Tested-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This fixes blur-like screen corruption on the following card:
VGA compatible controller [0300]: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller [8086:29c2] (rev 10)
intel_sdvo_mode_set() should not return prematurely just because some
features are not supported.
https://bugzilla.kernel.org/show_bug.cgi?id=17151
Signed-off-by: Pavel Roskin <proski@gnu.org>
Reported-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[ickle: Relax a couple more checks for failing LVDS modesetting]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 86f100b136.
The kref API requires the handlecount to be initialised to one on object
creation (so that kref_get() doesn't complain upon first use) so the
dalliance in the drivers is required in order to sink the initial
floating reference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
drivers/gpu/drm/i915/intel_overlay.c: In function 'intel_overlay_print_error_state':
drivers/gpu/drm/i915/intel_overlay.c:1467: error: implicit declaration of function 'seq_printf'
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16811
Reported-by: Martin Ziegler <ziegler@uni-freiburg.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Andre Muller <andremuellerster@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Only fallback to a set of default modes on a connector iff that
connector is known to be connected. The issue occurs that with limited
hardware which cannot probe a connector and so reports the
connector status as unknown will then attempt to retrieve the modes for
it during drm_helper_probe_single_connector_modes(). Should that fail,
the helper then generates a default set which fools the fb_helper and
causes havoc with the console and beyond.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Polling for a VGA device on an old system can be quite expensive,
causing latencies on the order of 600ms. As we hold the mode mutex for
this time and also need the same mutex to move the cursor, we trigger a
user-visible stall.
The real solution would involve improving the granulatity of the
locking and so perhaps performing some of the probing not under the lock
or some other updates can be done under different locks. Also reducing the
cost of probing for a non-existent monitor would be worthwhile. However,
exposing a parameter to disable polling is a simple workaround in the
meantime.
In order to accommodate users turning polling on and off at runtime, the
polling is potentially re-enabled on every probe. This is coupled to
the user calling xrandr, which seems to be a vaild time to reset the
polling timeout since the information on the connection has just been
updated. (The presumption being that all connections are probed in a
single xrandr pass, which is currently valid.)
References:
Bug 29536 - 2.6.35 causes ~600ms latency every 10s
https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bug 16265 - Why is kslowd accumulating so much CPU time?
https://bugzilla.kernel.org/show_bug.cgi?id=16265
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
digital underscan support regressed tv-out.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29985
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These VGT regs need to be programmed via the ring rather than
MMIO as on previous asics (r6xx/r7xx).
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In wm8350_dcdc_set_mode(), we set DCx_SLEEP bit of WM8350_DCDC_SLEEP_OPTIONS
register for REGULATOR_MODE_STANDBY mode.
( DCx_SLEEP bits: 0: Normal DC-DC operation 1: Select LDO mode )
In wm8350_dcdc_get_mode(), current logic to determinate
REGULATOR_MODE_STANDBY mode is just reverse.
( sleep is set should mean REGULATOR_MODE_STANDBY mode. )
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Problem description in current implementation:
When setting REGULATOR_MODE_IDLE mode, current implementation set
WM831X_LDO1_LP_MODE bit of ctrl_reg (which is wrong, it should clear the bit).
But due to a missing break statement for case REGULATOR_MODE_IDLE, the code
fall through to case REGULATOR_MODE_STANDBY and then clear
WM831X_LDO1_LP_MODE bit. So it still looks OK when checking the status
by wm831x_gp_ldo_get_mode().
When setting REGULATOR_MODE_STANDBY mode, it just does not work.
wm831x_gp_ldo_get_mode() will still return REGULATOR_MODE_IDLE because
the accordingly WM831X_LDO1_LP_MODE bit is clear.
Correct behavior should be:
Clear WM831X_LDO1_LP_MODE bit of ctrl_reg for REGULATOR_MODE_IDLE mode.
Set WM831X_LDO1_LP_MODE bit of ctrl_reg for REGULATOR_MODE_STANDBY mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
vhost should set worker to NULL on cgroups attach failure,
so that we won't try to destroy the worker again on close.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since 2.6.36-rc1, non-root users of vhost-net fail to attach
if they are in any cgroups.
The reason is that when qemu uses vhost, vhost wants to attach
its thread to all cgroups that qemu has. But we got the API backwards,
so a non-priveledged process (Qemu) tried to control
the priveledged one (vhost), which fails.
Fix this by switching to the new cgroup_attach_task_all,
and running it from the vhost thread.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For ISP82xx, the check for empty slot in request queue before posting command type 6
request was missing. This could lead to request queue entry corruptions causing
IO timeouts.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, if target sets the SCSI Status (with Check condition)
and there is no FCP residual bit set then driver does not check
for dropped frame. This could lead to data corruption.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fw_hung flag should be set ir-respective of if there is a
mbx command pending or not. Also the complete should be called
if there is a mbx waiting.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The seconds_since_last_heartbeat should be checked for consecutive
heartbeat checks. Currently it could happen that seconds_since_last_heartbeat
gets set to max (2 seconds) for non-consecutive heartbeat checks.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
selector is used as array index of info->supported_voltages
Thus the valid value range should be 0 .. info->voltages_len -1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@openource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In choose_voltage(), we use i as array index of info->vol_table.
The valid value range for i should be 0 .. ARRAY_SIZE(info->vol_table) - 1.
Take LDO1 as example, ARRAY_SIZE(LDO1_table) is 4, vol_nbits of LDO1 is 2.
for (i = 0; i < (2 << info->vol_nbits); i++) is equivalent to
for (i = 0; i < 8; i++)
which is wrong.
The same value range checking also applies for index in pm8607_list_voltage().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@openource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The cfg80211 api has introduced a few new fields. Rather than assume
what cfg80211 api does by default, set these explicitly.
Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lld_nand fails to build on arches without virt_to_bus. Since this driver
is specifically for hardware enablment on Moorestown, this patch adds
Moorestown MID support as a dependency.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taken from DPO_RT3070_LinuxSTA_V2.3.0.4_20100604.tar.bz2 and
2010_0709_RT2870_Linux_STA_v2.4.0.1.tar.bz2, with duplicates removed.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 90abdc3b9 converted all PCMCIA users away from io_req_t. In
das08_cs.c the converted IO lines mask setting was added but the old
line using the now inexistent p_dev->io was not removed.
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On one of my m68k test builds I get:
drivers/staging/spectra/ffsport.c: In function ‘ioctl_read_page_data’:
drivers/staging/spectra/ffsport.c:196: error: implicit declaration of function ‘kmalloc’
drivers/staging/spectra/ffsport.c:196: warning: assignment makes pointer from integer without a cast
drivers/staging/spectra/ffsport.c:212: error: implicit declaration of function ‘kfree’
drivers/staging/spectra/ffsport.c: In function ‘ioctl_write_page_data’:
drivers/staging/spectra/ffsport.c:229: warning: assignment makes pointer from integer without a cast
drivers/staging/spectra/ffsport.c: In function ‘SBD_setup_device’:
drivers/staging/spectra/ffsport.c:637: warning: assignment makes pointer from integer without a cast
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed lockup problem with bounce_buffer scatter list which caused
crashes in heavy loads. And minor code indentation cleanup in effected
area.
Removed whitespace and noted minor indentation changes in description as
pointed out by Joe Perches. (Thanks for reviewing Joe)
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increased storvsc ringbuffer and max_io_requests. This now more
closely mimics the numbers on Hyper-V. And will allow more IO requests
to take place for the SCSI driver.
Max_IO is set to double from what it was before, Hyper-V allows it and
we have had appliance builder requests to see if it was a problem to
increase the number.
Ringbuffer size for storvsc is now increased because I have seen A few buffer
problems on extremely busy systems. They were Set pretty low before.
And since max_io_requests is increased I Really needed to increase the buffer
as well.
Signed-off-by:Hank Janssen <hjanssen@microsoft.com>
Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed the value of the 64bit-hole inside ring buffer, this
caused a problem on Hyper-V when running checked Windows builds.
Checked builds of Windows are used internally and given to external
system integrators at times. They are builds that for example that all
elements in a structure follow the definition of that Structure. The bug
this fixed was for a field that we did not fill in at all (Because we do
Not use it on the Linux side), and the checked build of windows gives
errors on it internally to the Windows logs.
This fixes that error.
Signed-off-by:Hank Janssen <hjanssen@microsoft.com>
Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed bounce offset kmap problem by using correct index.
The symptom of the problem is that in some NAS appliances this problem
represents Itself by a unresponsive VM under a load with many clients writing
small files.
Signed-off-by:Hank Janssen <hjanssen@microsoft.com>
Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix missing functions for net_device_ops.
It's a bug when porting the drivers from 2.6.27 to 2.6.32. In 2.6.27,
the default functions for Ethernet, like eth_change_mtu(), were assigned
by ether_setup(). But in 2.6.32, these function pointers moved to
net_device_ops structure and no longer be assigned in ether_setup(). So
we need to set these functions in our driver code. It will ensure the
MTU won't be set beyond 1500. Otherwise, this can cause an error on the
server side, because the HyperV linux driver doesn't support jumbo frame
yet.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the 0xDAF8 to 0xDAFF PID range for ChamSys limited USB interface/wing products
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain USB devices, such as the Nokia X6 mobile phone, don't expose any
endpoint descriptors on some of their interfaces. If the ACM driver is forced
to probe all interfaces on a device the a NULL pointer dereference will occur
when the ACM driver attempts to use the endpoint of the alternative settings.
One way to get the ACM driver to probe all the interfaces is by using the
/sys/bus/usb/drivers/cdc_acm/new_id interface.
This patch checks that the endpoint pointer for the current alternate settings
is non-NULL before using it.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm.c : Manage pseudo-modem without AT commands capabilities
Enable to drive electronic simple gadgets based on microcontrolers.
The Interface descriptor is like this:
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0 None
Signed-off-by: Philippe Corbes <philippe.corbes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The command endpoint is either a bulk or interrupt endpoint, but using
the wrong type of transfer causes an error if CONFIG_USB_DEBUG is
enabled after commit f661c6f8c6, which
checks for this mismatch.
Detect which type of endpoint it is and use a bulk/int URB as
appropriate. There are other function calls specifying a bulk pipe,
but usb_clear_halt doesn't use the pipe type (only the endpoint) and
usb_bulk_msg auto-detects interrupt transfers.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable <stable@kernel.org> [.34 and newer]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB IDs needed to support the B&B USOPTL4-4P, USO9ML2-2P, and
USO9ML2-4P. This patch expands and corrects a typo in the patch sent
on 08-31-2010.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
S60 phones from Nokia and Samsung expose two ACM channels. The first is a modem
with a standard AT-command interface, which is picked up correctly by CDC-ACM.
The second ACM port is marked as having a vendor-specific protocol. This means
that the ACM driver will not claim the second channel by default.
This adds support for the second ACM channel for the following devices:
Nokia E63
Nokia E75
Nokia 6760 Slide
Nokia E52
Nokia E55
Nokia E72
Nokia X6
Nokia N97 Mini
Nokia 5800 Xpressmusic
Nokia E90
Samsung GTi8510 (INNOV8)
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB ID needed to support B&B Electronic's 2-port, optically-isolated,
powered, USB to RS485 converter.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using the remove sysfs file, the device configuration is set to -1
(unconfigured). This eventually unbind drivers with the bandwidth_mutex
held. Some drivers may call functions that hold said mutex, like
usb_reset_device. This is the case for rtl8187, for example. This will
lead to the same process holding the mutex twice, which deadlocks.
Besides, according to Alan Stern:
"The deadlock problem probably could be handled somehow, but there's a
separate issue: Until the usb_disable_device call finishes unbinding
the drivers, the drivers are free to continue using their allocated
bandwidth. We musn't change the bandwidth allocations until after the
unbinding is done. So this patch is indeed necessary."
Unbinding the driver before holding the bandwidth_mutex solves the
problem. If any operation after that fails, drivers are not bound again.
But that would be a problem anyway that the user may solve resetting the
device configuration to one that works, just like he would need to do in
most other failure cases.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Pirelli DP-L10 mobile is sold under various brand names. One, already
supported by cp210x, is the T-COM TC300. Here is the lsusb for that version:
-------------------------------------------------------------------
Bus 001 Device 002: ID 0489:e000 Foxconn / Hon Hai T-Com TC 300
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe000 T-Com TC 300
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 TC 300
iSerial 3 0001
[snip]
---------------------------------------------------------------------------
However the native Pirelli DP-L10 is not supported:
------------------------------------------------------------------
Bus 001 Device 003: ID 0489:e003 Foxconn / Hon Hai Pirelli DP-L10
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe003 Pirelli DP-L10
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 DP-L10
iSerial 3 0001
[snip]
-------------------------------------------------------------------------
All that is required is an extra USB_DEVICE entry:
{ USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM
+Mobile */
The patch adds that entry. Tested under 2.6.36-rc2 from git.
Signed-off-by: A E Lawrence <lawrence_a_e@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New device ID added for Balluff RFID reader.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unfortunately some of the hardware PID belonging to auto-install CDROM
(AICD) of Novatel modems found their way into the option module. This
causes the AICD to be treated as a modem in stead of a disk. Since the
modem ports do not appear until after the AICD is ejected, this
essentially disables the modem. After a couple of minutes the AICD
should auto-eject, but it is just too long a wait. The frequency of the
failure seems to depend on both the hardware and the linux distribution.
Here is a patch that fixes this up, and also adds a couple of new PID,
offering some explanations and removing some incomplete and unnecessary
comments.
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the following section mismatch warning,
by moving the function rndis_init() from .init.text to .text.
WARNING: vmlinux.o(.text+0x1aeca5a): Section mismatch in reference from the function rndis_bind_config() to the function .init.text:rndis_init()
The function rndis_bind_config() references
the function __init rndis_init().
This is often because rndis_bind_config lacks a __init
annotation or the annotation of rndis_init is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The iounmap(ehci->ohci_hcctrl_reg); should be the first thing we do
because the ioremap() was the last thing we did. Also if we hit any of
the goto statements in the original code then it would have led to a
NULL dereference of "ehci". This bug was introduced in: 796bcae736
"USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]"
I modified the few lines in front a little so that my code didn't
obscure the return success code path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DEBUG is defined unconditionally, remove it as this clutters the message log.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found a bug "by chance" in drivers/char/tty_io.c
I mean "by chance" because I was just reading the code of the
tty_find_polling_driver() to make a new tty_find_by_name() function.
In tty_find_polling_driver() the driver actually test "tty_line <=
p->num" while num refers to the number of struct tty_struct pointers
allocated for the p->ttys (p is a tty_driver), and tty_line is scanned
in a tty name, which can be for example ttyS2. Then tty_line equals 2.
And if p->num is 2, we have only p->ttys[0] and p->ttys[1], but no
p->ttys[2].
This is actually unharmful, for tty_find_polling_driver() is used only
in drivers/serial/kgdboc.c, and there's a test over there to find a
console with a matching index, which will never happen.
This is still a bug anyway.
Signed-off-by: Nathael Pajani <nathael.pajani@ed3l.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The large cleanup/rewrite of resources in commit ccf68e59e9
accidentally reverted an earlier fix in commit a19e8b2059.
So restore it here.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: stable <stable@kernel.org> [.34 and newer]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After 02f0777a0d "vc_origin" is no
longer reset to the screen buffer before calling the con_init() hook
of the new console driver.
If the old driver wasn't using a fixed scanout buffer (e.g. the case
of vgacon) "vc_origin" may be a pointer to a VRAM location, and its
contents aren't guaranteed to be preserved after calling con_deinit()
on the old driver and con_init() on the new driver, i.e. the
subsequent console resize may fill the framebuffer with garbage.
It can be reproduced in the transition from vgacon to the nouveau
framebuffer driver: in that case the legacy VGA aperture "vc_origin"
points to becomes unreadable after fbcon_init().
This patch reverts the mentioned commit. To avoid the problem it
intended to fix, stop using "vc_scr_end" in vc_do_resize() to
calculate how many rows we have to copy (actually the code looks
simpler this way without the help of "vc_scr_end").
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Cc: qiaochong <qiaochong@loongson.cn>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Async notifications other than link status are possible in certain
configurations. Remove the BUG_ON in the mcc completion processing path.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ONLINE registers can return 0xFFFFFFFF on more than one
occassion. On systems that care, reading these registers could
lead to problems.
So the new code decides that the ASIC has encountered and error
by reading the UE_STATUS_LOW/HIGH registers. AND them with
the mask values and a non-zero result indicates an error.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong packet statistics for multicast Rx was causing net-snmp error messages
every 15 seconds. Instead of picking the multicast stats from hardware,
now maintain it in the driver itself.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add no-get quirk for eGalax touch controller to avoid timeout at probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nv50: initialize ramht_refs list for faked 0 channel
drm/nouveau: Don't take struct_mutex around the pushbuf IOCTL.
drm/nouveau: Take fence spinlock before reading the last sequence.
We need it for PFIFO_INTR_CACHE_ERROR interrupt handling,
because nouveau_fifo_swmthd looks for matching gpuobj in
ramht_refs list.
It fixes kernel panic in nouveau_gpuobj_ref_find.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We don't need it and it can lead to lock order inversions with respect
to drm_global_mutex, potentially causing dead locks.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It fixes a race between the TTM delayed work queue and the GEM IOCTLs
(fdo bug 29583) uncovered by the BKL removal.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The max depth supported by T3 is 64K entries. This fixes a bug
introduced in commit 9918b28d ("RDMA/cxgb3: Increase the max CQ
depth") that causes stalls and possibly crashes in large MPI clusters.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
GCC warns about empty printf format strings, and after
the addition of %pV these existing such cases in the
scsi driver layer were exposed enough for the compiler
to start seeing them.
Based almost entirely upon a patch by Joe Perches.
[jejb: fix up sym53c8xx msg]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
warning: zero-length gnu_printf format string
Fix the above warning by inserting a space into the literal string.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The doorbell reset initially appears to work correctly,
the controller resets, comes up, some i/o can even be
done, but on at least some Smart Arrays in some servers,
it eventually causes a subsequent controller lockup due
to some kind of PCIe error, and kdump can end up leaving
the root filesystem in an unbootable state. For this
reason, until the problem is fixed, or at least isolated
to certain hardware enough to be avoided, the doorbell
reset should not be used at all.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The current code in tree has problems with Login.
This patch fixes the Login Failure .
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
[mnc: Can't believe I missed that.]
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Return of the bi_rw tests is no longer bool after commit 74450be1. So
testing against constants doesn't make sense anymore. Fix this bug in
osd_req_read by removing "== 1" in test.
This is not a problem now, where REQ_WRITE is 1, but this can change
in the future and we don't want to rely on that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This reverts commit de6be6c1f7.
After some discussion with Jarek Poplawski and Eric Dumazet, we've
decided that this change is incorrect.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 7th entry in a lot of evergreen i2c gpio tables is partially
zeroed. Fix the entry.
Should fix the missing ddc entry in:
https://bugs.freedesktop.org/show_bug.cgi?id=29255
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The tv parameter was added to disable the tv-out connector,
however, it caused a crash if it was set to 0 due to
drm_connector_init not getting called. If tv=0, don't
attempt to add the connector.
Might fix:
https://bugzilla.kernel.org/show_bug.cgi?id=17241
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV515
LVDS panels. The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This code was originally for forcing some clocks on certain asics.
However, this code was later moved to asic specific functions
for all of the affected asics. The only users of the original
code at this point were r600, rv770, and evergreen and the code
was not relevant for those asics. So, remove it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vortex_ioctl() was grabbing vortex_private::lock around its call to
generic_mii_ioctl(). This is no longer necessary since there are more
specific locks which the mdio_{read,write}() functions will obtain.
Worse, those functions do not save and restore IRQ flags when locking
the MII state, so interrupts will be enabled when generic_mii_ioctl()
returns.
Since there is currently no need for any function to call
mdio_{read,write}() while holding another spinlock, do not change them
to save and restore IRQ flags but remove the specification of ordering
between vortex_private::lock and vortex_private::mii_lock.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's something very important I forgot to tell you.
What?
Don't cross the GRO streams.
Why?
It would be bad.
I'm fuzzy on the whole good/bad thing. What do you mean, "bad"?
Try to imagine all the Internet as you know it stopping instantaneously
and every bit in every packet swapping at the speed of light.
Total packet reordering.
Right. That's bad. Okay. All right. Important safety tip. Thanks, Hubert
The simplest way to stop this is just avoid doing GRO on the second port.
Very few Marvell boards support two ports per ring, and GRO is just
an optimization.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus resources must be released on exit
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its currently illegal to call kthread_stop(NULL)
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduced by 49dce689 ("spi doesn't need class_device") and bad-fixed
by 350d0076 ("spi: fix double-free on spi_unregister_master"),
spi_unregister_master would previously device_unregister all of the spi
master's siblings (instead of its children). hilarity ensues.
fix it to unregister children.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It is the next patch which is fixing missing header
which were removed from prom.h.
Related patches:
"of/address: Clean up function declarations" (sha1 id 22ae782f8)
"of: Fix missing includes" (sha1 id f1ca09b2b)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The S3C64xx SPI driver requires the machine to call s3c64xx_spi_set_info()
to select a few options, including the clock to use for the SPI controller.
If this is not done then a NULL will be passed as the clock name for
clk_get(), causing an obscure crash. Guard against this and other missing
configuration by validating that the clock name has been filled in in
the platform data that ets passed in.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, the address return from regulator_register()
is different from the address for regulator_unregister().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
max8998->dev is NULL in current implementation, set it to &pdev->dev.
regulator_register() still return success if max8998->dev is NULL,
but rdev->dev.parent will be set to NULL which is incorrect.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The third parameter of tps6586x_set_bits() is the bit_mask,
thus we should use (1 << ri->go_bit) instead of ri->go_bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
val is used as array index of ri->voltages.
Thus the valid value range should be 0 .. ri->desc.n_voltages - 1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Set max8998->num_regulators = pdata->num_regulators,
otherwise it's default value is 0.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We only use max8998->rdev[0] .. max8998->rdev[pdata->num_regulators-1],
max8998->rdev[pdata->num_regulators] is not used.
Thus fix the memory allocation size.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This driver is a platform driver, not a i2c driver.
Thus remove incorrect tps6507x_remove comments.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
A little bit improvement in the logic of choosing selector.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, ab8500_regulator_info[0].regulator is not
unregistered if the error happen at i > 0.
This patch fixes the resource leak and also improves the readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, ab3100_regulators[0].rdev is not unregistered if
the error happen at i > 0.
This patch fixes the resource leak and also improves the readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I moved the dereference of "ab8500" below the check for NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We need to call platform_device_unregister(i8042_platform_device)
before calling platform_driver_unregister() because i8042_remove()
resets i8042_platform_device to NULL. This leaves the platform device
instance behind and prevents driver reload.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=16613
Reported-by: Seryodkin Victor <vvscore@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
By visual inspection, the reported touch_major and touch_minor axes
are a factor of two too small. Presumably the device actually reports
the semi-major and semi-minor axes. Corrected with this patch.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The 5 GHz CTL indexes were not being read for all hardware
devices due to the masking out through the CTL_MODE_M mask
being one bit too short. Without this the calibrated regulatory
maximum values were not being picked up when devices operate
on 5 GHz in HT40 mode. The final output power used for Atheros
devices is the minimum between the calibrated CTL values and
what CRDA provides.
Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM is compressed on AR9003, upon decompression
the wrong upper limit was being used for the block which
prevented the 5 GHz CTL indexes from being used, which are
stored towards the end of the EEPROM block. This fix allows
the actual intended regulatory limits to be used on AR9003
hardware.
Cc: stable@kernel.org [2.6.36+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael reported that p54* never really entered power
save mode, even tough it was enabled.
It turned out that upon a power save mode change the
firmware will set a special flag onto the last outgoing
frame tx status (which in this case is almost always the
designated PSM nullfunc frame). This flag confused the
driver; It erroneously reported transmission failures
to the stack, which then generated the next nullfunc.
and so on...
Cc: <stable@kernel.org>
Reported-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids a NULL pointer dereference as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=625889
When the WARN condition is hit in ieee80211_get_tx_rate, it will return
NULL. So, we need to check the return value and avoid dereferencing it
in that case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Acked-by: Bob Copeland <me@bobcopeland.com>
This patch adds a quirk for the eGalax touch controller which reports
two pairs of axes.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When an erroneous PEB is scheduling for scrubbing, we end up with the
following oops:
[<c0162404>] (prot_queue_del+0x0/0x50) from [<c01635b4>] (ubi_wl_scrub_peb+0xec/0x13c)
[<c01634c8>] (ubi_wl_scrub_peb+0x0/0x13c) from [<c01603bc>] (ubi_eba_read_leb+0x200/0x428)
[<c01601bc>] (ubi_eba_read_leb+0x0/0x428) from [<c015e3c0>] (ubi_leb_read+0xe8/0x138)
[<c015e2d8>] (ubi_leb_read+0x0/0x138) from [<c00d6918>] (ubifs_start_scan+0x7c/0xf4)
[<c00d689c>] (ubifs_start_scan+0x0/0xf4) from [<c00e3650>] (ubifs_recover_leb+0x3c/0x730)
[<c00e3614>] (ubifs_recover_leb+0x0/0x730) from [<c00e444c>] (ubifs_recover_log_leb+0xc8/0x2dc)
[<c00e4384>] (ubifs_recover_log_leb+0x0/0x2dc) from [<c00d7c20>] (ubifs_replay_journal+0xb90/0x13a4)
[<c00d7090>] (ubifs_replay_journal+0x0/0x13a4) from [<c00cdd68>] (ubifs_fill_super+0xb84/0x1054)
[<c00cd1e4>] (ubifs_fill_super+0x0/0x1054) from [<c00ced04>] (ubifs_get_sb+0xc4/0x2ac)
[<c00cec40>] (ubifs_get_sb+0x0/0x2ac) from [<c007f04c>] (vfs_kern_mount+0x58/0x94)
[<c007eff4>] (vfs_kern_mount+0x0/0x94) from [<c007f0e8>] (do_kern_mount+0x40/0xe8)
[<c007f0a8>] (do_kern_mount+0x0/0xe8) from [<c0095628>] (do_new_mount+0x68/0x8c)
[<c00955c0>] (do_new_mount+0x0/0x8c) from [<c00957a8>] (do_mount+0x15c/0x1b8)
[<c009564c>] (do_mount+0x0/0x1b8) from [<c0095890>] (sys_mount+0x8c/0xd4)
[<c0095804>] (sys_mount+0x0/0xd4) from [<c0023c00>] (ret_fast_syscall+0x0/0x2c)
Kernel panic - not syncing: Fatal exception
The problem is that 'ubi_wl_scrub_peb()' does not expect that PEBs may
be in the erroneous tree, which is a bug. This patch fixes the bug
and adds corresponding check to 'ubi_wl_scrub_peb()'. Now it will simply
ignore erroneous PEBs, instead of causing an oops.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
MD_CHANGE_CLEAN is used for two different purposes and this leads to
confusion.
One of the purposes is largely mirrored by MD_CHANGE_PENDING which is
not used for anything else, so have MD_CHANGE_PENDING take over that
purpose fully.
The two purposes are:
1/ tell md_update_sb that an update is needed and that it is just a
clean/dirty transition.
2/ tell user-space that an transition from clean to dirty is pending
(something wants to write), and tell te kernel (by clearin the
flag) that the transition is OK.
The first purpose remains wit MD_CHANGE_CLEAN, the second is moved
fully to MD_CHANGE_PENDING.
This means that various places which conditionally set or cleared
MD_CHANGE_CLEAN no longer need to be conditional.
Signed-off-by: NeilBrown <neilb@suse.de>
If this bit is cleared in md_update_sb() the kernel will allow writes to the
array if userspace triggers md_allow_write(), e.g. through stripe_cache_size,
when mdmon is not active. When mdmon is active the array transitions to
active-idle bypassing write-pending, setting up a race for mdmon to set the
array clean before a write arrives.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Commit 0798cea8c2 "UBI: improve corrupted flash handling"
broke delet-compatible volumes handling - it introduced a limit of 8 eraseblocks which
may be corrupted. And delete-compatible eraseblocks are added to the "corrupted" list,
so if we'd have a large delete-compatible volume, UBI would refuse it.
The fix is to add delete-compatible volumes to the erase list instead. Indeed, they are
corrupted, we just have to erase them.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
list_for_each_entry uses its first argument to move from one element to the
next, so modifying it can break the iteration. The variable re1 is already
used within the loop as a temporary variable, and is not live here.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
iterator name list_for_each_entry;
expression x,E;
position p1,p2;
@@
list_for_each_entry@p1(x,...) { <... x =@p2 E ...> }
@@
expression x,E;
position r.p1,r.p2;
statement S;
@@
*x =@p2 E
...
list_for_each_entry@p1(x,...) S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
commit: 812d046915
drm/radeon/kms/r7xx: add workaround for hw issue with HDP flush
breaks on AGP boards since there is no VRAM gart table.
This patch fixes the issue by creating a VRAM scratch page so that
can be used on both AGP and PCIE.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29834
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rather than calling get_memory_clock and get_engine_clock,
used the tracked values from the pm code. Calling the tables
adds additional latency in the modesetting and pm paths.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: work around VIA and NEC PHY packet reception bug
firewire: core: do not use del_timer_sync() in interrupt context
firewire: net: fix unicast reception RCODE in failure paths
firewire: sbp2: fix stall with "Unsolicited response"
firewire: sbp2: fix memory leak in sbp2_cancel_orbs or at send error
ieee1394: Adjust confusing if indentation
VIA VT6306, VIA VT6308, and NEC OrangeLink controllers do not write
packet event codes for received PHY packets (or perhaps write
evt_no_status, hard to tell). Work around it by overwriting the
packet's ACK by ack_complete, so that upper layers that listen to PHY
packet reception get to see these packets.
(Also tested: TI TSB82AA2, TI TSB43AB22/A, TI XIO2213A, Agere FW643,
JMicron JMB381 --- these do not exhibit this bug.)
Clemens proposed a quirks flag for that, IOW whitelist known misbehaving
controllers for this workaround. Though to me it seems harmless enough
to enable for all controllers.
The log_ar_at_event() debug log will continue to show the original
status from the DMA unit.
Reported-by: Clemens Ladisch <clemens@ladisch.de> (VT6308)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
For MT slots, the ABS_MT_TRACKING_ID determines whether a slot is in use,
but currently leaves initialization up to the drivers. This patch sets the
slot state to unused upon creation.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The KIOCSOUND and KDMKTONE ioctls are based on the CLOCK_TICK_RATE,
which is architecture and sometimes configuration specific.
In practice, most user applications assume that it is actually defined
as the i8253 PIT base clock of 1193182 Hz, which is true on some
architectures but not on others.
This patch makes the vt code use the PIT frequency on all
architectures, which is much more well-defined. It will change the
behavior of user applications sending the beep ioctl on all
architectures that define CLOCK_TICK_RATE different from
PIT_TICK_RATE.
The original breakage was introduced in commit bcc8ca099 "Adapt
drivers/char/vt_ioctl.c to non-x86". Hopefully, reverting this change
will make the frequency correct in more cases than it will make it
incorrect.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This fixes a regression introduced in
3b57ca0f80.
The data[6] byte contains either 1 or -1 depending on the whether the
mouse wheel on older wacom tablets is moved down (1) or up (-1). The
patch introduced in the above commit changed the cast from (signed char)
to (signed). When cast as a signed integer and negated, the value of -1
(stored in the byte as 0xff) became -255 rather than 1. This patch
reverts the cast to a (signed char) and also removes an unnecessary
(signed) cast, as all the values operated on are bitmasked.
Signed-off-by: Mike Auty <ikelos@gentoo.org>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Cc; stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
pcnet_cs:
add new_id: "KENTRONICS KEP-230" 10Base-T PCMCIA card.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net/ipv4: Eliminate kstrdup memory leak
net/caif/cfrfml.c: use asm/unaligned.h
ax25: missplaced sock_put(sk)
qlge: reset the chip before freeing the buffers
l2tp: test for ethernet header in l2tp_eth_dev_recv()
tcp: select(writefds) don't hang up when a peer close connection
tcp: fix three tcp sysctls tuning
tcp: Combat per-cpu skew in orphan tests.
pxa168_eth: silence gcc warnings
pxa168_eth: update call to phy_mii_ioctl()
pxa168_eth: fix error handling in prope
pxa168_eth: remove unneeded null check
phylib: Fix race between returning phydev and calling adjust_link
caif-driver: add HAS_DMA dependency
3c59x: Fix deadlock between boomerang_interrupt and boomerang_start_tx
qlcnic: fix poll implementation
netxen: fix poll implementation
bridge: netfilter: fix a memory leak
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
vgaarb: Wrap vga_(get|put) in CONFIG_VGA_ARB
drm/radeon/kms: add missing scratch update in dp_detect
drm/modes: Fix CVT-R modeline generation
drm: fix regression in drm locking since BKL removal.
drm/radeon/kms: remove stray radeon_i2c_destroy
drm: mm: fix range restricted allocations
drm/nouveau: drop drm_global_mutex before sleeping in submission path
drm: export drm_global_mutex for drivers to use
drm/nv20: Don't use pushbuf calls on the original nv20.
drm/nouveau: Fix TMDS on some DCB1.5 boards.
drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel.
drm/nv30: Apply modesetting to the correct slave encoder
drm/nouveau: Use a helper function to match PCI device/subsystem IDs.
drm/nv50: add dcb type 14 to enum to prevent compiler complaint
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Do not report error overflow as a separate error
MCE, AMD: Limit MCE decoding to current families for now
The commit 886275ce41 (param: lock
if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes)
introduced new fields into the if_sdio_card structure. It caused
missalignment of the if_sdio_card.buffer field and failure at driver
load time:
~# modprobe libertas_sdio
[ 62.315124] libertas_sdio: Libertas SDIO driver
[ 62.319976] libertas_sdio: Copyright Pierre Ossman
[ 63.020629] DMA misaligned error with device 48
[ 63.025207] mmci-omap-hs mmci-omap-hs.1: unexpected dma status 800
[ 66.005035] libertas: command 0x0003 timed out
[ 66.009826] libertas: Timeout submitting command 0x0003
[ 66.016296] libertas: PREP_CMD: command 0x0003 failed: -110
Adding explicit alignment attribute for the if_sdio_card.buffer field
fixes this problem.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids byte access to the NFC buffer. Byte access to the
NFC is not allowed.
The patch is against linux-next 20100618.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16651
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Adam Serbinski <adam@serbinksi.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This locking path needs proper auditing but probably too late for changes at this point for 2.6.36, so lets go with the quick fix, which is to drop the lock around schedule.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I missed this one in the i2c unification patch. This
is handled in the core radeon i2c code now.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the code cleanup in
7a6b2896f2 is the first bad commit
commit 7a6b2896f2
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 2 15:02:15 2010 +0100
drm_mm: extract check_free_mm_node
I've botched up the range-restriction checks. The result is usually
an X server dying with SIGBUS in libpixman (software fallback rendering).
Change the code to adjust the start and end for range restricted
allocations. IMHO this even makes the code a bit clearer.
Fixes regression bug: https://bugs.freedesktop.org/show_bug.cgi?id=29738
Reported-by-Tested-by: Till MAtthiesen <entropy@everymail.net>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nouveau: drop drm_global_mutex before sleeping in submission path
drm: export drm_global_mutex for drivers to use
drm/nv20: Don't use pushbuf calls on the original nv20.
drm/nouveau: Fix TMDS on some DCB1.5 boards.
drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel.
drm/nv30: Apply modesetting to the correct slave encoder
drm/nouveau: Use a helper function to match PCI device/subsystem IDs.
drm/nv50: add dcb type 14 to enum to prevent compiler complaint
If we keep hold of the mutex here, the process which currently holds the
buffer object will never be able to release it, causing a deadlock.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Qlge is freeing the buffers before stopping the card DMA, and
this can cause some severe error, as a EEH event on PPC.
This patch just stop the card and then free the resources.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Overflow MCi_STATUS bit is set, EDAC reports the lost error
with a "no information available" message which often puzzles users
parsing the dmesg. This doesn't make much sense since this error has
been lost anyway so no need for reporting it separately. Thus, report
the overflow bit setting in the MCE dump instead. While at it, remove
reporting of MiscV and ErrorEnable (en) which are superfluous.
Now it looks like this:
[ 1501.650024] MC4_STATUS: Corrected error, other errors lost: yes, CPU context corrupt: no, CECC Error
[ 1501.666887] Northbridge Error, node 2
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The "return" command is buggy on the original nv20, it jumps back to
the caller address as expected, but it doesn't clear the subroutine
active bit making the subsequent pushbuf calls fail with a "stack"
overflow.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The TMDS output of an nv11 was being detected as LVDS, because it uses
DCB type 2 for TMDS instead of type 4.
Reported-by: Bertrand VIEILLE <Vieille.Bertrand@free.fr>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Remove harmful BUG_ON() from ata_bmdma_qc_issue(),
as it casts too wide of a net and breaks sata_mv.
It also crashes the kernel while doing the BUG_ON().
There's already a WARN_ON_ONCE() further down to catch
the case of POLLING for a BMDMA operation.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
Fix DSM/TRIM commands in sata_mv (v2).
These need to be issued using old-school "BM DMA",
rather than via the EDMA host queue.
Since the chips don't have proper BM DMA status,
we need to be more careful with setting the ATA_DMA_INTR bit,
since DSM/TRIM often has a long delay between "DMA complete"
and "command complete".
GEN_I chips don't have BM DMA, so no TRIM for them.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
ata_qc_issue() BUG_ON()s on data commands w/o data, which may be
submitted via SG_IO. Be less of a drama queen and just trigger
WARN_ON_ONCE() and fail the command with AC_ERR_SYSTEM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stefan Hübner <stefan.huebner@stud.tu-ilmenau.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dma_dwc_xfer_setup() returns an int and "dma_chan" needs to be signed
for the error handling to work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
88SE9128 can do FBS and sets it in HOST_CAP but forgets to set FBSCP
in PORT_CMD. Implement AHCI_HFLAG_YES_FBS and apply it to 88SE9128.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Winbond W83759A controller is fully supported by pata_legacy driver
so remove no longer needed pata_winbond driver.
Leave PATA_WINBOND_VLB config option for compatibility reasons
and teach pata_legacy to preserve the old behavior of pata_winbond
driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
