This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers don't implement a FIFO in hardware, but fill their
mailboxes in a particular order (from lowest to highest or highest to lowest).
This makes problems to read the frames in the correct order from the hardware,
as new frames might be filled into just read (low) mailboxes. This gets worse,
when following new frames are received into not read (higher) mailboxes.
On the bright side some these CAN controllers put a timestamp on each received
CAN frame. This patch adds support to offload CAN frames in interrupt context,
order them by timestamp and then transmitted in a NAPI context.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers have a usable FIFO already but can still benefit
from off-loading the CAN controller FIFO. The CAN frames of the FIFO are
read and put into a skb queue during interrupt and then transmitted in a
NAPI context.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error return ret is never zero in the error handling path in
softingcs_probe, so the check for non-zero and returning -ENODEV
is logically dead code and hence redundant. Remove it and just
return ret.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN interfaces only support fixed fixed bitrates. This patch adds a
netlink interface to get the list of the CAN interface's fixed bitrates and
data bitrates.
Inside the driver arrays of supported data- bitrate values are defined.
const u32 drvname_bitrate[] = { 20000, 50000, 100000 };
const u32 drvname_data_bitrate[] = { 200000, 500000, 1000000 };
struct drvname_priv *priv;
priv = netdev_priv(dev);
priv->bitrate_const = drvname_bitrate;
priv->bitrate_const_cnt = ARRAY_SIZE(drvname_bitrate);
priv->data_bitrate_const = drvname_data_bitrate;
priv->data_bitrate_const_cnt = ARRAY_SIZE(drvname_data_bitrate);
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Until commit
08da7da41e can: provide a separate bittiming_const parameter to
bittiming functions
it was possible to have devices not providing bittiming_const. This can
be used for hardware that only support pre-defined fixed bitrates.
Although no mainline driver is using this feature so far.
This patch re-introduces this feature for the bitrate and the data
bitrate (of CANFD controllers). The driver can specify the
{data_,}bittiming_const (if the bittiming parameters should be
calculated from the bittiming_const) as before or no
{data_,}bittiming_const but implement the do_set_{data,}bittiming
callback.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a netlink interface to configure the CAN bus termination of
CAN interfaces.
Inside the driver an array of supported termination values is defined:
const u16 drvname_termination[] = { 60, 120, CAN_TERMINATION_DISABLED };
struct drvname_priv *priv;
priv = netdev_priv(dev);
priv->termination_const = drvname_termination;
priv->termination_const_cnt = ARRAY_SIZE(drvname_termination);
priv->termination = CAN_TERMINATION_DISABLED;
And the funtion to set the value has to be defined:
priv->do_set_termination = drvname_set_termination;
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Ramesh Shanmugasundaram <Ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to make the driver work with the common clock framework, this
patch converts the clk_enable()/clk_disable() to
clk_prepare_enable()/clk_disable_unprepare().
Also add error checking for clk_prepare_enable().
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The priv->device pointer for c_can_pci is never set, but it is used
without a NULL check in c_can_start(). Setting it in c_can_pci_probe()
like c_can_plat_probe() prevents c_can_pci.ko from crashing, with and
without CONFIG_PM.
This might also cause the pm_runtime_*() functions in c_can.c to
actually be executed for c_can_pci devices - they are the only other
place where priv->device is used, but they all contain a null check.
Signed-off-by: Einar Jón <tolvupostur@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
That's the default now, no need for makefiles to set it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but should be
more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to go...
Lots of plain-text files have also been converted and integrated.
- Images in binary formats have been replaced with more source-friendly
versions.
- Various bits of organizational work, including the renaming of various
files discussed at the kernel summit.
- New documentation for the device_link mechanism.
...and, of course, lots of typo fixes and small updates.
-----BEGIN PGP SIGNATURE-----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=A0EV
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"These are the documentation changes for 4.10.
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but
should be more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to
go... Lots of plain-text files have also been converted and
integrated.
- Images in binary formats have been replaced with more
source-friendly versions.
- Various bits of organizational work, including the renaming of
various files discussed at the kernel summit.
- New documentation for the device_link mechanism.
... and, of course, lots of typo fixes and small updates"
* tag 'docs-4.10' of git://git.lwn.net/linux: (193 commits)
dma-buf: Extract dma-buf.rst
Update Documentation/00-INDEX
docs: 00-INDEX: document directories/files with no docs
docs: 00-INDEX: remove non-existing entries
docs: 00-INDEX: add missing entries for documentation files/dirs
docs: 00-INDEX: consolidate process/ and admin-guide/ description
scripts: add a script to check if Documentation/00-INDEX is sane
Docs: change sh -> awk in REPORTING-BUGS
Documentation/core-api/device_link: Add initial documentation
core-api: remove an unexpected unident
ppc/idle: Add documentation for powersave=off
Doc: Correct typo, "Introdution" => "Introduction"
Documentation/atomic_ops.txt: convert to ReST markup
Documentation/local_ops.txt: convert to ReST markup
Documentation/assoc_array.txt: convert to ReST markup
docs-rst: parse-headers.pl: cleanup the documentation
docs-rst: fix media cleandocs target
docs-rst: media/Makefile: reorganize the rules
docs-rst: media: build SVG from graphviz files
docs-rst: replace bayer.png by a SVG image
...
Fix for bad memory access while disconnecting. netdev is freed before
private data free, and dev is accessed after freeing netdev.
This makes a slub problem, and it raise kernel oops with slub debugger
config.
Signed-off-by: Jiho Chu <jiho.chu@samsung.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlhAJY0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklam88B/0dgD2R9D8udVyHnp1CGVrWm+REER49
g6V2ZqIqfxaAFEiQFIhySJJtWYt4vHAC2A3Mwx6yyv9qugYb26LCiSt3XQPlPNY4
yVFpVzOMsFjmSu9PQ7u47b7/IKmqmSuuuQQWm3rDxDQC+KLKmH1TfULXzqDQ/yR/
+gNTvi6Zwfi6rFU7B33I6cT0VhfnWXhbAbBdg4jNmW5WAyz+WT6c9J9oXQMRw5VW
ESTYrU2c+IVK3Z3e0BOmnCytaPrxE6j1OmT0LNsVR5aoXDmK3jDNln/7cPEOCkD3
3t9ub+gqfeaMIjyDI3yBcy75Gjk3mFQMXs/3LVTivwZySgGldOak/iyL
=vXN1
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.10-20161201' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-12-01
this is a pull request of 4 patches for net-next/master.
There are two patches by Chris Paterson for the rcar_can and rcar_canfd
device tree binding documentation. And a patch by Geert Uytterhoeven
that corrects the order of interrupt specifiers.
The fourth patch by Colin Ian King fixes a spelling error in the
kvaser_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake "oustanding" to "outstanding" in
comment and dev_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This adds support for PEAK-System PCAN-USB X6 USB to CAN interface.
The CAN FD adapter PCAN-USB X6 allows the connection of up to 6 CAN FD
or CAN networks to a computer via USB. The interface is installed in an
aluminum profile casing and is shipped in versions with D-Sub connectors
or M12 circular connectors.
The PCAN-USB X6 registers in the USB sub-system as if 3x PCAN-USB-Pro FD
adapters were plugged. So, this patch:
- updates the PEAK_USB entry of the corresponding Kconfig file
- defines and adds the device id. of the PCAN-USB X6 (0x0014) into the
table of supported device ids
- defines and adds the new software structure implementing the PCAN-USB X6,
which is obviously a clone of the software structure implementing the
PCAN-USB Pro FD.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This fixes the bitimings fields ranges supported by all the CAN-FD USB
interfaces of the PEAK-System CAN-FD adapters.
Very first development versions of the IP core API defined smaller TSGEx
and SJW fields for both nominal and data bittimings records than the
production versions. This patch fixes them by enlarging their sizes to
the actual values:
field: old size: fixed size:
nominal TSGEG1 6 8
nominal TSGEG2 4 7
nominal SJW 4 7
data TSGEG1 4 5
data TSGEG2 3 4
data SJW 2 4
Note that this has no other consequences than offering larger choice to
bitrate encoding.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Moxa CAN devices.
Signed-off-by: Lukas Resch <l.resch@incubedit.com>
Signed-off-by: Christoph Zehentner <c.zehentner@incubedit.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A timer was used to restart after the bus-off state, leading to a
relatively large can_restart() executed in an interrupt context,
which in turn sets up pinctrl. When this happens during system boot,
there is a high probability of grabbing the pinctrl_list_mutex,
which is locked already by the probe() of other device, making the
kernel suspect a deadlock condition [1].
To resolve this issue, the restart_timer is replaced by a delayed
work.
[1] https://github.com/victronenergy/venus/issues/24
Signed-off-by: Sergei Miroshnichenko <sergeimir@emcraft.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Configure the transmitter delay register at +0x1c to correctly handle
the CAN FD bitrate switch (BRS). This moves the SSP (secondary sample
point) to a proper offset, so that the TDC mechanism works and won't
generate error frames on the CAN link.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On a imx6ul-pico board the following error is seen during system suspend:
dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110
PM: Device 2090000.flexcan failed to resume: error -110
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Silent ignorance of errors during probe procedure is a bad thing, this
patch fixes it. Extra message added for hardware initialization
failure. Such common issues are mostly caused by wrong wiring. Message
about success added as well, it should be useful to debug new hardware
configuration, especially in case of several CAN buses.
Signed-off-by: Ed Spiridonov <edo.rus@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As per Wolfgang G, all new drivers should support decreasing state
transition(back-to-error-active). This patch adds this support.
This driver configures the controller to halt on bus-off entry. Hence,
when in error states less than bus off state, the TEC/REC counters
are checked for lower state transition eligibility and action.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The controller can operate in one of the two global modes
- CAN FD only mode (default)
- Classical CAN (CAN2.0) only mode
This patch adds support for Classical CAN only mode. It can be enabled
by defining the optional device tree property "renesas,no-can-fd" of this
node.
Note: R-Car Gen3 h/w manual v0.51E shows bit6 of RSCFDnCFDGCFG as
reserved, which is incorrect. This bit is same as RSCFDnGCFG.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Kvaser Leaf Light HS v2 OEM, Mini PCI
Express 2xHS and USBcan Light 2xHS.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...
This patch adds a private dellink function for the CAN device driver interface
that does just nothing.
It's a follow up to commit 993e6f2fd ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With upstream commit bb208f144c (can: fix handling of unmodifiable
configuration options) a new can_validate() function was introduced.
When invoking 'ip link set can0 type can' without any configuration data
can_validate() tries to validate the content without taking into account that
there's totally no content. This patch adds a check for missing content.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patchs adds basic support for the bytewerk.org candleLight interface,
a open hardware (CERN OHL) USB CAN adapter.
Signed-off-by: Hubert Denkmair <hubert@denkmair.de>
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Amr Bekhit <amrbekhit@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.
The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.
Testing performed on Altera CycloneV (D_CAN). Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch clubs the Renesas controller drivers in one rcar dir.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
