Adds a check on the Transmission Complete bit status before closing the
com port. Prevents the port closure before the end of the transmission.
TC poll loop is moved from stm32_tx_dma_complete to stm32_shutdown
routine, in order to check TC before shutdown in both dma and
PIO tx modes.
TC clear is added in stm32_transmit_char routine, in order to be cleared
before transmitting in both dma and PIO tx modes.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disables the tx irq when the transmission is ended and updates stop_tx
conditions for code cleanup.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fixes a rx data error when data length < 8 bits and parity is enabled.
RDR register MSB is used for parity bit reception.
- Adds a mask to ignore MSB when data is get from RDR.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fixes parity and framing error bit by clearing parity and framing error
flag. The current implementation doesn't clear the error bits when an
error is detected.
- Fixes the incorrect name of framing error clearing flag in header file.
- Fixes misalignement between data frame and errors status. The status
read for "n" frame was the status of "n+1" frame".
- Fixes break detection was not triggered by the expected register.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 supports either:
- 8 and 9 bits word length (including parity bit) for stm32f4 compatible
devices
- 7, 8 and 9 bits word length (including parity bit) for stm32f7 and
stm32h7 compatible devices.
As a consequence STM32 supports the following termios configurations:
- CS7 with parity bit, and CS8 (with or without parity bit) for stm32f4
compatible devices.
- CS6 with parity bit, CS7 and CS8 (with or without parity bit) for
stm32f7 and stm32h7 compatible devices.
This patch is fixing word length by configuring correctly the SoC with
supported configurations.
Fixes: ada8618ff3 ("serial: stm32: adding support for stm32f7")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datasheet states:
Bit 4: ClockEnSet the ClockEn bit high to enable an external clocking
(crystal or clock generator at XIN). Set the ClockEn bit to 0 to disable
clocking
Bit 1: CrystalEnSet the CrystalEn bit high to enable the crystal
oscillator. When using an external clock source at XIN, CrystalEn must
be set low.
The bit 4, MAX310X_CLKSRC_EXTCLK_BIT, should be set and was not.
This was required to make the MAX3107 with an external crystal on our
board able to send or receive data.
Signed-off-by: Joe Burmeister <joe.burmeister@devtank.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted in commit 84b40e3b57 ("serial: 8250: omap: Disable DMA for
console UART"), UART console lines use low-level PIO only access functions
which will conflict with use of the line when DMA is enabled, e.g. when
the console line is also used for systemd messages. So disable DMA
support for UART console lines.
Reported-by: Michael Rodin <mrodin@de.adit-jv.com>
Link: https://patchwork.kernel.org/patch/10929511/
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time the DMA engine signals a transaction error the driver prints
a message at error level. Getting transaction errors is pretty much
expected on baudrate mismatches and the correspoding error counters
are increased in this case properly. Remove the error message which
is possibly repeated at a very high rate which can lock up the whole
system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the tty layer requests the uart to throttle, the current code
executing in msm_serial will trigger "Bad mode in Error Handler" and
generate an invalid stack frame in pstore before rebooting (that is if
pstore is indeed configured: otherwise the user shall just notice a
reboot with no further information dumped to the console).
This patch replaces the PIO byte accessor with the word accessor
already used in PIO mode.
Fixes: 68252424a7 ("tty: serial: msm: Support big-endian CPUs")
Cc: stable@vger.kernel.org
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Batch read mode doesn't check any conditions or flags except the Rx
overflow one. But it may only happen after the last character is pushed
into the RHR register. In this case we shouldn't push all the read
characters with overrun flag set, but only the last one caused the
FIFO overflow. This commit splits the characters retrieval loop into
two parts. First one is ordinary intsert-chars procedure without taking
the overrun status into account. Second part inserts the last character
checking whether the overrun happened and pushing a '\0' character with
TTY_OVERRUN flag to a flip-buffer.
If we left the loop the way it was the '\0' character would be inserted
after each character retrieved at the overrun occasion.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART port might be pre-configured with rs485 enabled flag at the
time of the port starting up process. In this case we need to
have the hardware rs485-related registers initialized in accordance
with the rs485 flags and settings provided by the configs descriptor.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently sets the echo suppression bit by default when rs485
is enabled. Naturally it disables any data retrieval in rs485 mode while
RTSn is pushed up. The receiver gate (RX_) can be enabled just by clearing
(or not setting) the EchoSuprs bit of mode2 register. So by setting or
clearing the bit we implement the SER_RS485_RX_DURING_TX rs485 flag
support.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current calculator doesn't do it' job quite correct. First of all the
max310x baud-rates generator supports the divisor being less than 16.
In this case the x2/x4 modes can be used to double or quadruple
the reference frequency. But the current baud-rate setter function
just filters all these modes out by the first condition and setups
these modes only if there is a clocks-baud division remainder. The former
doesn't seem right at all, since enabling the x2/x4 modes causes the line
noise tolerance reduction and should be only used as a last resort to
enable a requested too high baud-rate.
Finally the fraction is supposed to be calculated from D = Fref/(c*baud)
formulae, but not from D % 16, which causes the precision loss. So to speak
the current baud-rate calculator code works well only if the baud perfectly
fits to the uart reference input frequency.
Lets fix the calculator by implementing the algo fully compliant with
the fractional baud-rate generator described in the datasheet:
D = Fref / (c*baud), where c={16,8,4} is the x1/x2/x4 rate mode
respectively, Fref - reference input frequency. The divisor fraction is
calculated from the same formulae, but making sure it is found with a
resolution of 0.0625 (four bits).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPI transfer tx/rx buffers must be DMA-safe and the structure
documentation clearly states this. Data declared on the system stack isn't
DMA-safe [1]. Instead at least kernel memory should be used for the
buffers. In order to fix this here we can create the buffers at the device
probing stage and use them without any synchronization, since batch
read/write methods are called from non-reentrant contexts - either from
rx-event IRQ threaded handler or from the tx workqueue item.
[1] Documentation/DMA-API-HOWTO.txt
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_port structure instance is embedded into the max310x_one
super-structure, which is accessed by some of the uart-port callback
methods. In order to improve the callback's code readability lets
define the to_max310x_port() wrapper which just translates the passed
uart_port pointer to the max310x_one one. It is also going to be
handy in future commits.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since cmwq introduction in the kernel, workqueues've been turned into
non-reentrant execution contexts [1]. It means any work item is
guaranteed to be executed by at most one worker system-wide at any
given time. Since tx-handler max310x_handle_tx() is called by a
single work item we don't need it to be self-protected by the mutex.
We also don't need to check the tx work item pending state before
scheduling it (which in the first place was racy btw), since cmwq will
make sure to reschedule the item if it wasn't pending at the moment of
schedule_work() call.
[1] Documentation/core-api/workqueue.rst
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PL011 register space includes all necessary status bits to
determine whether a device instance requires handling in response
to an interrupt. Therefore, multiple instances of the device could
be serviced by a single shared interrupt, which is the case on BCM7211.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_dbg statement should print the value of uart.port.mapbase instead
of its address. Besides that, uart.port.irq and uart.port.iotype are all
unsigned types, so using %u is more appropriate.
Signed-off-by: Hao Lee <haolee.swjtu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch set contains an assortment of RISC-V related patches that I'd
like to target for the 5.2 merge window. Most of the patches are
cleanups, but there are a handful of user-visible changes:
* The nosmp and nr_cpus command-line arguments are now supported, which
work like normal.
* The SBI console no longer installs itself as a preferred console, we
rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
* sfence_remove_sfence_vma{,_asid} now pass their arguments along to the
SBI call.
* Modules now support BUG().
* A missing sfence.vma during boot has been added. This bug only
manifests during boot.
* The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get things
running on the Unleashed. The latest master from this morning merges in
cleanly and passes the tests as well.
This patch set rebased my "5.2 MW, Part 1" patch set which includes an
erronous empty file. It's also a rebase of my "5.2 MW, Part 2" patch
set, in which I managed to create another file while attempting to
remove the empty file.
Sorry for all the noise!
-----BEGIN PGP SIGNATURE-----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=mZwx
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains an assortment of RISC-V related patches that I'd like to
target for the 5.2 merge window. Most of the patches are cleanups, but
there are a handful of user-visible changes:
- The nosmp and nr_cpus command-line arguments are now supported,
which work like normal.
- The SBI console no longer installs itself as a preferred console,
we rely on standard mechanisms (/chosen, command-line, hueristics)
instead.
- sfence_remove_sfence_vma{,_asid} now pass their arguments along to
the SBI call.
- Modules now support BUG().
- A missing sfence.vma during boot has been added. This bug only
manifests during boot.
- The arch/riscv support for SiFive's L2 cache controller has been
merged, which should un-block the EDAC framework work.
I've only tested this on QEMU again, as I didn't have time to get
things running on the Unleashed. The latest master from this morning
merges in cleanly and passes the tests as well"
* tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits)
riscv: fix locking violation in page fault handler
RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs
RISC-V: Add DT documentation for SiFive L2 Cache Controller
RISC-V: Avoid using invalid intermediate translations
riscv: Support BUG() in kernel module
riscv: Add the support for c.ebreak check in is_valid_bugaddr()
riscv: support trap-based WARN()
riscv: fix sbi_remote_sfence_vma{,_asid}.
riscv: move switch_mm to its own file
riscv: move flush_icache_{all,mm} to cacheflush.c
tty: Don't force RISCV SBI console as preferred console
RISC-V: Access CSRs using CSR numbers
RISC-V: Add interrupt related SCAUSE defines in asm/csr.h
RISC-V: Use tabs to align macro values in asm/csr.h
RISC-V: Fix minor checkpatch issues.
RISC-V: Support nr_cpus command line option.
RISC-V: Implement nosmp commandline option.
RISC-V: Add RISC-V specific arch_match_cpu_phys_id
riscv: vdso: drop unnecessary cc-ldoption
riscv: call pm_power_off from machine_halt / machine_power_off
...
The Linux kernel will auto-disables all boot consoles whenever it
gets a preferred real console.
Currently on RISC-V systems, if we have a real console which is not
RISCV SBI console then boot consoles (such as earlycon=sbi) are not
auto-disabled when a real console (ttyS0 or ttySIF0) is available.
This results in duplicate prints at boot-time after kernel starts
using real console (i.e. ttyS0 or ttySIF0) if "earlycon=" kernel
parameter was passed by bootloader.
The reason for above issue is that RISCV SBI console always adds
itself as preferred console which is causing other real consoles
to be not used as preferred console.
Ideally "console=" kernel parameter passed by bootloaders should
be the one selecting a preferred real console.
This patch fixes above issue by not forcing RISCV SBI console as
preferred console.
Fixes: afa6b1ccfa ("tty: New RISC-V SBI console driver")
Cc: stable@vger.kernel.org
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
When kernel panic happens, it will first print the panic call stack,
then the ending msg like:
[ 35.743249] ---[ end Kernel panic - not syncing: Fatal exception
[ 35.749975] ------------[ cut here ]------------
The above message are very useful for debugging.
But if system is configured to not reboot on panic, say the
"panic_timeout" parameter equals 0, it will likely print out many noisy
message like WARN() call stack for each and every CPU except the panic
one, messages like below:
WARNING: CPU: 1 PID: 280 at kernel/sched/core.c:1198 set_task_cpu+0x183/0x190
Call Trace:
<IRQ>
try_to_wake_up
default_wake_function
autoremove_wake_function
__wake_up_common
__wake_up_common_lock
__wake_up
wake_up_klogd_work_func
irq_work_run_list
irq_work_tick
update_process_times
tick_sched_timer
__hrtimer_run_queues
hrtimer_interrupt
smp_apic_timer_interrupt
apic_timer_interrupt
For people working in console mode, the screen will first show the panic
call stack, but immediately overridden by these noisy extra messages,
which makes debugging much more difficult, as the original context gets
lost on screen.
Also these noisy messages will confuse some users, as I have seen many bug
reporters posted the noisy message into bugzilla, instead of the real
panic call stack and context.
Adding a flag "suppress_printk" which gets set in panic() to avoid those
noisy messages, without changing current kernel behavior that both panic
blinking and sysrq magic key can work as is, suggested by Petr Mladek.
To verify this, make sure kernel is not configured to reboot on panic and
in console
# echo c > /proc/sysrq-trigger
to see if console only prints out the panic call stack.
Link: http://lkml.kernel.org/r/1551430186-24169-1-git-send-email-feng.tang@intel.com
Signed-off-by: Feng Tang <feng.tang@intel.com>
Suggested-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and
support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips
and support for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma,
rcar-dmac, stm32-dma etc
- dev_get_drvdata() updates on few drivers
-----BEGIN PGP SIGNATURE-----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=JDU6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips and support
for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma, rcar-dmac,
stm32-dma etc
- dev_get_drvdata() updates on few drivers
* tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (34 commits)
dmaengine: tegra210-adma: restore channel status
dmaengine: tegra210-dma: free dma controller in remove()
dmaengine: tegra210-adma: add pause/resume support
dmaengine: tegra210-adma: add support for Tegra186/Tegra194
Documentation: DT: Add compatibility binding for Tegra186
dmaengine: tegra210-adma: prepare for supporting newer Tegra chips
dmaengine: at_xdmac: remove a stray bottom half unlock
dmaengine: fsl-edma: Adjust indentation
dmaengine: fsl-edma: Fix typo in Vybrid name
dmaengine: stm32-dma: fix residue calculation in stm32-dma
dmaengine: nbpfaxi: Use dev_get_drvdata()
dmaengine: bcm-sba-raid: Use dev_get_drvdata()
dmaengine: stm32-dma: Fix unsigned variable compared with zero
dmaengine: stm32-dma: use platform_get_irq()
dmaengine: rcar-dmac: Update copyright information
dmaengine: imx-sdma: Only check ratio on parts that support 1:1
dmaengine: xgene-dma: fix spelling mistake "descripto" -> "descriptor"
dmaengine: idma64: Move driver name to the header
dmaengine: bcm2835: Drop duplicate capability setting.
dmaengine: pl330: _stop: clear interrupt status
...
Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKvrw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynR2wCfTrWM9Qm7oA1hgWeYZiLTrnYnOtsAoK4a629W
o7AAyVf8RJ4jdWaSgOqx
=9Dy/
-----END PGP SIGNATURE-----
Merge tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (45 commits)
tty: serial: add driver for the SiFive UART
dt-bindings: serial: add documentation for the SiFive UART driver
serial: uartps: Add support for cts-override
dt-bindings: xilinx-uartps: Add support for cts-override
serial: milbeaut_usio: Fix error handling in probe and remove
tty: rocket: deprecate the rp_ioctl
tty: rocket: Remove RCPK_GET_STRUCT ioctl
tty: update obsolete termios comment
tty: serial_core: fix error code returned by uart_register_driver()
serial: 8250-mtk: modify baudrate setting
serial: 8250-mtk: add follow control
docs: serial: convert docs to ReST and rename to *.rst
serial: 8250_exar: Adjust IOT2000 matching
TTY: serial_core, add ->install
serial: Fix using plain integer instead of Null pointer
tty:serial_core: Spelling mistake
tty: Add NULL TTY driver
tty: vt: keyboard: Allow Unicode compose base char
Revert "tty: fix NULL pointer issue when tty_port ops is not set"
serial: Add Milbeaut serial control
...
Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here, along
with some new IIO drivers.
Also we ended up deleting two drivers, making this pull request remove a
few hundred thousand lines of code, always a nice thing to see. Both of
the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from those
locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by the
various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come in
the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHGMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynQRACgwtlC6DFsEFwCplYxQXP5uzuIVTMAoJ61xzC0
Qim7K31f5ulaa3GJuhzo
=zEY5
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here,
along with some new IIO drivers.
The "counter" subsystem was added in here as well, as it is needed by
the IIO drivers and subsystem.
Also we ended up deleting two drivers, making this pull request remove
a few hundred thousand lines of code, always a nice thing to see. Both
of the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from
those locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by
the various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come
in the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon"
[ I fixed up the warning myself - Linus ]
* tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (663 commits)
staging: kpc2000: kpc_spi: Fix build error for {read,write}q
Staging: rtl8192e: Remove extra space before break statement
Staging: rtl8192u: ieee80211: Fix if-else indentation warning
Staging: rtl8192u: ieee80211: Fix indentation errors by removing extra spaces
staging: most: cdev: fix chrdev_region leak in mod_exit
staging: wlan-ng: Fix improper SPDX comment style
staging: rtl8192u: ieee80211: Resolve ERROR reported by checkpatch
staging: vc04_services: bcm2835-camera: Compress two lines into one line
staging: rtl8723bs: core: Use !x in place of NULL comparison.
staging: rtl8723bs: core: Prefer using the BIT Macro.
staging: fieldbus: anybus-s: fix wait_for_completion_timeout return handling
staging: kpc2000: fix up build problems with readq()
staging: rtlwifi: move remaining phydm .h files
staging: rtlwifi: strip down phydm .h files
staging: rtlwifi: delete the staging driver
staging: fieldbus: anybus-s: rename bus id field to avoid confusion
staging: fieldbus: anybus-s: keep device bus id in bus endianness
Staging: sm750fb: Change *array into *const array
staging: rtl8192u: ieee80211: Fix spelling mistake
staging: rtl8192u: ieee80211: Replace bit shifting with BIT macro
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Make the forward declaration actually match the real function
definition, something that previous versions of gcc had just ignored.
This is another patch to fix new warnings from gcc-9 before I start the
merge window pulls. I don't want to miss legitimate new warnings just
because my system update brought a new compiler with new warnings.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a serial driver for the SiFive UART, found on SiFive FU540 devices
(among others).
The underlying serial IP block is relatively basic, and currently does
not support serial break detection. Further information on the IP
block can be found in the documentation and Chisel sources:
https://static.dev.sifive.com/FU540-C000-v1.0.pdfhttps://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/uart
This driver was written in collaboration with Wesley Terpstra
<wesley@sifive.com>.
Tested on a SiFive HiFive Unleashed A00 board, using BBL and the open-
source FSBL (using a DT file based on what's targeted for mainline).
This revision incorporates changes based on comments by Julia Lawall
<julia.lawall@lip6.fr>, Emil Renner Berthing <kernel@esmil.dk>, and
Andreas Schwab <schwab@suse.de>. Thanks also to Andreas for testing
the driver with his userspace and reporting a bug with the
set_termios implementation.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Wesley Terpstra <wesley@sifive.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Emil Renner Berthing <kernel@esmil.dk>
Cc: Andreas Schwab <schwab@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having flow is configurable. Add support for the same by
checking for cts-override.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_clk_get() is used so there is no reason to explicitly call
clk_put() in probe or remove functions. Also remove duplicate assign
for port->membase.
Fixes: ba44dc0430 ("serial: Add Milbeaut serial control")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rp_ioctl is deprecated.
Add dev_warn_ratelimited to warn the use of rp_ioctl.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the cmd is RCPK_GET_STRUCT, copy_to_user will copy
info to user space. As info->port.ops is the address of
a constant object rocket_port_ops (assigned in init_r_port),
a kernel address leakage happens.
Remove the RCPK_GET_STRUCT ioctl.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update an obsolete comment referring to the termios_locked structure
which was removed over a decade ago by commit fe6e29fdb1 ("tty:
simplify ktermios allocation").
While at it, fix the "Thus" typo.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver() returned -ENOMEM on any error, even when
tty_register_driver() call returned another one, such as -EBUSY.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SW and HW follow control function.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The converted files are focused at the Kernel internal API,
so, this is a good candidate for the kernel API set of books.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there are more IOT2040 variants with identical hardware but
different asset tags, the asset tag matching should be adjusted to
support them.
As only the IOT2040 variants have the Exar chip on board, matching on
their board name is enough. In the future there will be no other devices
with the "SIMATIC IOT2000" DMI board name but different hardware.
Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to compute the uart state only on the first open. This is
usually what is done in the ->install hook. serial_core used to do this
in ->open on every open. So move it to ->install.
As a side effect, it ensures the state is set properly in the window
after tty_init_dev is called, but before uart_open. This fixes a bunch
of races between tty_open and flush_to_ldisc we were dealing with
recently.
One of such bugs was attempted to fix in commit fedb576064 (serial:
fix race between flush_to_ldisc and tty_open), but it only took care of
a couple of functions (uart_start and uart_unthrottle). I was able to
reproduce the crash on a SLE system, but in uart_write_room which is
also called from flush_to_ldisc via process_echoes. I was *unable* to
reproduce the bug locally. It is due to having this patch in my queue
since 2012!
general protection fault: 0000 [#1] SMP KASAN PTI
CPU: 1 PID: 5 Comm: kworker/u4:0 Tainted: G L 4.12.14-396-default #1 SLE15-SP1 (unreleased)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c89-prebuilt.qemu.org 04/01/2014
Workqueue: events_unbound flush_to_ldisc
task: ffff8800427d8040 task.stack: ffff8800427f0000
RIP: 0010:uart_write_room+0xc4/0x590
RSP: 0018:ffff8800427f7088 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 000000000000002f RSI: 00000000000000ee RDI: ffff88003888bd90
RBP: ffffffffb9545850 R08: 0000000000000001 R09: 0000000000000400
R10: ffff8800427d825c R11: 000000000000006e R12: 1ffff100084fee12
R13: ffffc900004c5000 R14: ffff88003888bb28 R15: 0000000000000178
FS: 0000000000000000(0000) GS:ffff880043300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000561da0794148 CR3: 000000000ebf4000 CR4: 00000000000006e0
Call Trace:
tty_write_room+0x6d/0xc0
__process_echoes+0x55/0x870
n_tty_receive_buf_common+0x105e/0x26d0
tty_ldisc_receive_buf+0xb7/0x1c0
tty_port_default_receive_buf+0x107/0x180
flush_to_ldisc+0x35d/0x5c0
...
0 in rbx means tty->driver_data is NULL in uart_write_room. 0x178 is
tried to be dereferenced (0x178 >> 3 is 0x2f in rdx) at
uart_write_room+0xc4. 0x178 is exactly (struct uart_state *)NULL->refcount
used in uart_port_lock from uart_write_room.
So revert the upstream commit here as my local patch should fix the
whole family.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Li RongQing <lirongqing@baidu.com>
Cc: Wang Li <wangli39@baidu.com>
Cc: Zhang Yu <zhangyu31@baidu.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build warning that using plain integer as Null pointer.
This is reported by kbuild test robot.
Fixes: ba44dc0430 ("serial: Add Milbeaut serial control")
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch breaks set_selection() into two functions so that when
called from kernel, copy_from_user() can be avoided. The two functions
are called set_selection_user() and set_selection_kernel() in order to
be explicit about their purposes. This also means updating any
references to set_selection() and fixing for name change. It also
exports set_selection_kernel() and paste_selection().
These changes are used the following patch where speakup's selection
functionality calls into the above functions, thereby doing away with
parallel implementation.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Gregory Nowak <greg@gregn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err_spi is only called within SERIAL_SC16IS7XX_SPI
while err_i2c is called inside SERIAL_SC16IS7XX_I2C.
So we need to put err_spi and err_i2c into each #ifdef
accordingly.
This change fixes ("sc16is7xx: move label 'err_spi'
to correct section").
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch a6dbe44275 ("vt: perform safe console erase in the right
order") introduced a bug. The conditional do_update_region() was
replaced by a call to update_region() that does contain the conditional
already, but with unwanted extra side effects such as restoring the cursor
drawing.
In order to reproduce the bug:
- use framebuffer console with the AMDGPU driver
- type "links" to start the console www browser
- press 'q' and space to exit links
Now the cursor will be permanently visible in the center of the
screen. It will stay there until something overwrites it.
The bug goes away if we change update_region() back to the conditional
do_update_region().
[ nico: reworded changelog ]
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Cc: stable@vger.kernel.org
Fixes: a6dbe44275 ("vt: perform safe console erase in the right order")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make
the label only available under SERIAL_SC16IS7XX_SPI option.
Otherwise, the below warning appears.
drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label]
err_spi:
^~~~~~~
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Fixes: ac0cdb3d99 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The calculation of the sampling point has min() and max() exchanged.
Fix this by using the clamp() helper instead.
Fixes: 63ba1e00f1 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several issues with the formula used for calculating the
deviation from the intended rate:
1. While min_err and last_stop are signed, srr and baud are unsigned.
Hence the signed values are promoted to unsigned, which will lead
to a bogus value of deviation if min_err is negative,
2. Srr is the register field value, which is one less than the actual
sampling rate factor,
3. The divisions do not use rounding.
Fix this by casting unsigned variables to int, adding one to srr, and
using a single DIV_ROUND_CLOSEST().
Fixes: 63ba1e00f1 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no console driver is enabled (or if a non-present driver is selected
with something like console=null in an attempt to disable the console),
opening /dev/console errors out, and init scripts and other userspace
code that relies on the existence of a console will fail. Symlinking
/dev/null to /dev/console does not solve the problem since /dev/null
does not behave like a real TTY.
To just provide a dummy console to userspace when no console driver is
available or desired, add a ttynull driver which simply discards all
writes. It can be chosen on the command line in the standard way, i.e.
with console=ttynull.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass Unicode character to k_unicode handler function to honor possible
accent_table definition.
With introduction of KDSKBDIACRUC ioctl, it has been possible to set
compose characters (diacr, base and result) to any Unicode character
(below 0xf000 code point) as defined in struct kbdiacruc.
But it does not work with characters beyond Latin-1 as base, because
they are printed early and not passed to any of the handler functions,
thus breaking compose and dead keys.
It affects keyboard layouts defining such characters on level 1 and
relying on dead keys to access level 3 (e.g., lv-modern with some
modifications for extra characters on level 3 for ē, ā and ī keys).
Signed-off-by: Reinis Danne <rei4dan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f4e68d58cf.
TTY drivers using the tty-port abstraction all provide a pointer to a
set of port operations, which specifically cannot be NULL (or we'd find
out at first attempt to open a port).
Revert the recent commit which added unnecessary NULL-checks and whose
commit message indicated that it was fixing a real problem, which it did
not.
Note that even the two tty drivers for virtual devices currently
providing an empty set of operations probably should be implementing at
least some of the callbacks.
Cc: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Milbeaut serial control including earlycon and console.
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GIO_UNIMAP can easily result in a high order allocation,
seen 6th order allocation on radeondrmfb:
fbcon: radeondrmfb (fb0) is primary device
Console: switching to colour frame buffer device 160x64
radeon 0000:01:05.0: fb0: radeondrmfb frame buffer device
WARNING: CPU: 0 PID: 78661 at mm/page_alloc.c:3532
__alloc_pages_nodemask+0x1b1/0x600
order 6 >= 3, gfp 0x40d0
The warning is generated by a debug patch.
At the same time it's safe to use kvmalloc() for allocation in
con_get_unimap(), so let's do the substitution.
And do the same for con_set_unimap().
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return from tty_write_room could potentially be negative if
a tty write_room driver returns an error number (not that any seem
to do). Rather than just check for a zero return, also check for
a -ve return. This avoids the unsigned nr being set to a large unsigned
value on the assignment from variable space and can lead to overflowing
the buffer buf. Better to be safe than assume all write_room
implementations in tty drivers are going to do the right thing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There were a few straggling files under drivers/tty/ that did not have
any SPDX identifier either because they entered the tree recently, or
they somehow missed the mass-tagging of commit b24413180f ("License
cleanup: add SPDX GPL-2.0 license identifier to files with no license")
This commit follows the same rule as b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license") where files
without any specified license in them fall under GPL-2.0 as the correct
license for the individual file. Add that identifier to these remaining
files so that we don't have to guess at the license of them in the
future.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were a few Kconfig and Makefiles under drivers/tty/ that were
missing a SPDX identifier. Fix that up so that automated tools can
properly classify all kernel source files.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b9ca5f8560 as 0-day
shows it has a circular locking dependency.
Fixes: b9ca5f8560 ("tty: pty: Fix race condition between release_one_tty and pty_write")
Reported-by: kernel test robot <lkp@intel.com>
Cc: Sahara <keun-o.park@darkmatter.ae>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both /dev/vcs and /dev/vcs0 were in use in the past, but these days
/dev/vcs0 is mostly historical curiosity.
* "/dev/vcs" is the name that has always been in the Linux allocated
devices list.
* "vcs" is the device name in sysfs since Linux v2.6.12.
* MAKEDEV(1) in Debian used to create /dev/vcs0 only, but /dev/vcs was
added in 1999: https://bugs.debian.org/45698
* MAKEDEV(1) in RedHat switched from /dev/vcs0 to /dev/vcs in 2000:
* Fri Oct 20 2000 Nalin Dahyabhai <nalin@redhat.com>
- change vcs0 to vcs (ditto for vcsa0)
Signed-off-by: Jakub Wilk <jwilk@jwilk.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Especially when a linked tty is used such as pty, the linked tty
port's buf works have not been cancelled while master tty port's
buf work has been cancelled. Since release_one_tty and flush_to_ldisc
run in workqueue threads separately, when pty_cleanup happens and
link tty port is freed, flush_to_ldisc tries to access freed port
and port->itty, eventually it causes a panic.
This patch utilizes the magic value with holding the tty_mutex to
check if the tty->link is valid.
Fixes: 2b022ab754 ("pty: cancel pty slave port buf's work in tty_release")
Signed-off-by: Sahara <keun-o.park@darkmatter.ae>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, in the userspace, it was possible to use the "setterm" command
from util-linux to blank the VT console by default, using the following
command.
According to the man page,
> The force option keeps the screen blank even if a key is pressed.
It was implemented by calling TIOCL_BLANKSCREEN.
case BLANKSCREEN:
ioctlarg = TIOCL_BLANKSCREEN;
if (ioctl(STDIN_FILENO, TIOCLINUX, &ioctlarg))
warn(_("cannot force blank"));
break;
However, after Linux 4.12, this command ceased to work anymore, which is
unexpected. By inspecting the kernel source, it shows that the issue was
triggered by the side-effect from commit a4199f5eb8 ("tty: Disable
default console blanking interval").
The console blanking is implemented by function do_blank_screen() in vt.c:
"blank_state" will be initialized to "blank_normal_wait" in con_init() if
AND ONLY IF ("blankinterval" > 0). If "blankinterval" is 0, "blank_state"
will be "blank_off" (== 0), and a call to do_blank_screen() will always
abort, even if a forced blanking is required from the user by calling
TIOCL_BLANKSCREEN, the console won't be blanked.
This behavior is unexpected from a user's point-of-view, since it's not
mentioned in any documentation. The setterm man page suggests it will
always work, and the kernel comments in uapi/linux/tiocl.h says
> /* keep screen blank even if a key is pressed */
> #define TIOCL_BLANKSCREEN 14
To fix it, we simply remove the "blank_state != blank_off" check, as
pointed out by Nicolas Pitre, this check doesn't logically make sense
and it's safe to remove.
Suggested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Fixes: a4199f5eb8 ("tty: Disable default console blanking interval")
Signed-off-by: Yifeng Li <tomli@tomli.me>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipw->attr_memory and ipw->common_memory are assigned with the
return value of ioremap. ioremap may fail, but no checks
are enforced. The fix inserts the checks to avoid potential
NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intention was clearly to use the tty_pgrp local variable rather than
re-read tty->pgrp outside of ctrl_lock, so do that.
This bug was introduced by commit 2812d9e9fd ("tty: Combine
SIGTTOU/SIGTTIN handling").
Signed-off-by: David Emett <dave@sp4m.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building with W=1 reports (among other things):
CC drivers/tty/tty_jobctrl.o
drivers/tty/tty_jobctrl.c:317: warning: Cannot understand *
on line 317 - I thought it was a doc line
Fix up the non-kerneldoc comment. (other warnings to be cleaned up in separate patch)
Signed-off-by Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems which don't provide arch_trigger_cpumask_backtrace() will
invoke showacpu() from a smp_call_function() function which is invoked
with disabled interrupts even on -RT systems.
The function acquires the show_lock lock which only purpose is to
ensure that the CPUs don't print simultaneously. Otherwise the
output would clash and it would be hard to tell the output from CPUx
apart from CPUy.
On -RT the spin_lock() can not be acquired from this context. A
raw_spin_lock() is required. It will introduce the system's latency
by performing the sysrq request and other CPUs will block on the lock
until the request is done. This is okay because the user asked for a
backtrace of all active CPUs and under "normal circumstances in
production" this path should not be triggered.
Signed-off-by: Julien Grall <julien.grall@arm.com>
[bigeasy@linuxtronix.de: commit description]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike 'client_ops' which is initialized to 'default_client_ops', the
port operations 'ops' may be left to NULL.
Check the 'ops' value before checking the 'ops->x' value.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is an ACPI method to enumerate such devices via specific ACPI ID
and use of compatible strings. It will not work for the drivers which
have no OF match ID table present.
Reported-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of open coded variants, switch to direct use of
device_get_match_data().
Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the property is provided and there are no other possibilities to detect
UART clock frequency, use it as a fallback.
Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DMA mode support for the Spreadtrum serial controller.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds power management for the Spreadtrum serial controller.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warning:
drivers/tty/serial/8250/8250_fintek.c:306:6: warning:
symbol 'fintek_8250_set_termios' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Echo "" to /sys/module/kgdboc/parameters/kgdboc will fail with "No such
device” error.
This is caused by function "configure_kgdboc" who init err to ENODEV
when the config is empty (legal input) the code go out with ENODEV
returned.
Fixes: 2dd4531686 ("kgdboc: Fix restrict error")
Signed-off-by: Wentao Wang <witallwang@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In half-duplex operation, RX should be started after TX completes.
If DMA is used, there is a case when the DMA transfer completes but the
TX FIFO is not emptied, so the RX cannot be restarted just yet.
Use a boolean variable to store this state and rearm TX interrupt mask
to be signaled again that the transfer finished. In interrupt transmit
handler this variable is used to start RX. A warning message is generated
if RX is activated before TX fifo is cleared.
Fixes: b389f173aa ("tty/serial: atmel: RS485 half duplex w/DMA: enable
RX after TX is done")
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper function to check that a port needs to use half duplex
communication, replacing several occurrences of multi-line bit checking.
Fixes: b389f173aa ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel IOMMU, when enabled, tries to find the domain of the device,
assuming it's a PCI one, during DMA operations, such as mapping or
unmapping. Since we are splitting the actual PCI device to couple of
children via MFD framework (see drivers/mfd/intel-lpss.c for details),
the DMA device appears to be a platform one, and thus not an actual one
that performs DMA. In a such situation IOMMU can't find or allocate
a proper domain for its operations. As a result, all DMA operations are
failed.
In order to fix this, supply parent of the platform device
to the DMA engine framework and fix filter functions accordingly.
We may rely on the fact that parent is a real PCI device, because no
other configuration is present in the wild.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey has reported on OpenWrt's bug tracking system[1], that he
currently can't use ar93xx_uart as pure serial UART without console
(CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined),
because compilation ends with following error:
ar933x_uart.c: In function 'ar933x_uart_console_write':
ar933x_uart.c:550:14: error: 'struct uart_port' has no
member named 'sysrq'
So this patch moves all the code related to console handling behind
series of CONFIG_SERIAL_AR933X_CONSOLE ifdefs.
1. https://bugs.openwrt.org/index.php?do=details&task_id=2152
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Andrey Batyiev <batyiev@gmail.com>
Reported-by: Andrey Batyiev <batyiev@gmail.com>
Tested-by: Andrey Batyiev <batyiev@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/tty/serial/qcom_geni_serial.c:1079:6: warning: variable 'baud'
is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
It's not wrong; when options is NULL, baud has no default value. Use
9600 as that is a sane default.
Link: https://github.com/ClangBuiltLinux/linux/issues/395
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing uart_unregister_driver() and i2c_del_driver() before return
from sc16is7xx_init() in the error handling case.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case ioremap fails, the fix returns -ENOMEM to avoid NULL
pointer dereferences.
Multiple places use port.membase.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device can return a NULL pointer when matching device is not
found. This patch avoids a scenario causing NULL pointer derefernce.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device on failure to find a matching device can return a NULL
pointer. The patch checks for such a scenrio and passes the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers
multi-block support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
-----BEGIN PGP SIGNATURE-----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=Ykvn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
-----BEGIN PGP SIGNATURE-----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=57/1
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20190305' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"A lucky 13 audit patches for v5.1.
Despite the rather large diffstat, most of the changes are from two
bug fix patches that move code from one Kconfig option to another.
Beyond that bit of churn, the remaining changes are largely cleanups
and bug-fixes as we slowly march towards container auditing. It isn't
all boring though, we do have a couple of new things: file
capabilities v3 support, and expanded support for filtering on
filesystems to solve problems with remote filesystems.
All changes pass the audit-testsuite. Please merge for v5.1"
* tag 'audit-pr-20190305' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: mark expected switch fall-through
audit: hide auditsc_get_stamp and audit_serial prototypes
audit: join tty records to their syscall
audit: remove audit_context when CONFIG_ AUDIT and not AUDITSYSCALL
audit: remove unused actx param from audit_rule_match
audit: ignore fcaps on umount
audit: clean up AUDITSYSCALL prototypes and stubs
audit: more filter PATH records keyed on filesystem magic
audit: add support for fcaps v3
audit: move loginuid and sessionid from CONFIG_AUDITSYSCALL to CONFIG_AUDIT
audit: add syscall information to CONFIG_CHANGE records
audit: hand taken context to audit_kill_trees for syscall logging
audit: give a clue what CONFIG_CHANGE op was involved
Existing driver checks for alternate clock if devm_clk_get() fails
and returns error code for last clock failure. If xilinx_uartps is
called before clock driver, devm_clk_get() returns -EPROBE_DEFER.
In this case, probe should not check for alternate clock as main
clock is already present in DTS and return -EPROBE_DEFER only.
This patch fixes it by not checking for alternate clock when main
clock get returns -EPROBE_DEFER.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the source clock is not divisible by the expected baud rate and
the remainder is not less than half of the expected baud rate, the old
formular will round up the frequency division coefficient. This will
make the actual baud rate less than the expected value and can not meet
the external transmission requirements.
Thus this patch modifies the baud rate calculation formula to support
the serial controller output the maximum baud rate.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two other drivers that bind to mrvl,mmp-uart and both of them
assume register shift of 2 bits. There are device trees that lack the
property and rely on that assumption.
If this driver wins the race to bind to those devices, it should behave
the same as the older deprecated driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the other OF-enabled drivers, use the port number from the firmware if
the devicetree specifies an alias:
aliases {
...
serial2 = &uart2; /* Should be ttyS2 */
}
This is how the deprecated pxa.c driver behaved, switching to 8250_pxa
messes up the numbering.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/tty/hvc/hvc_xen.c: In function ‘xencons_backend_changed’:
drivers/tty/hvc/hvc_xen.c:493:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (dev->state == XenbusStateClosed)
^
drivers/tty/hvc/hvc_xen.c:496:2: note: here
case XenbusStateClosing:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/tty/n_gsm.c: In function ‘gsm_dlci_data’:
drivers/tty/n_gsm.c:1582:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (tty) {
^
drivers/tty/n_gsm.c:1587:2: note: here
case 1:
^~~~
drivers/tty/n_gsm.c: In function ‘gsm1_receive’:
CC [M] drivers/scsi/snic/snic_disc.o
CC [M] drivers/net/wireless/realtek/rtlwifi/pci.o
CC drivers/usb/early/xhci-dbc.o
drivers/tty/n_gsm.c:1981:12: warning: this statement may fall through [-Wimplicit-fallthrough=]
gsm->fcs = INIT_FCS;
^
drivers/tty/n_gsm.c:1983:2: note: here
case GSM_ADDRESS: /* Address continuation */
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the complexities of modern Qualcomm SoCs, about a half dozen drivers
must successfully probe before the clocks for the console are present, and
the console can successfully probe. Depending on several random factors
such as probe order and modules vs builtin, msm_serial may not be able to
successfully probe for some, at which point, __init annotated functions
may become unmapped. If this occurs, msm_console_setup() will be called
from the probe path, but will no longer exist, resulting in a kernel
panic.
Resolve this issue by removing the __init annotation from
msm_console_setup().
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
