To handle error trigger table correctly, memory region must be
removed from request region. We had a series of patches to do this
culminating in:
commit b4e008dc5
ACPI, APEI, EINJ, Refine the fix of resource conflict
but when ACPI5 support was added, we missed updating this area. So
when using EINJ table on an ACPI5 enabled machine, we get following error:
APEI: Can not request [mem 0x526b80000-0x526b80007] for APEI EINJ
Trigger registers
Fix this by checking for the acpi5 case and using the same code
that was added earlier.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Since commit 2c60db0370 ('net: provide a default dev->ethtool_ops')
all devices have a non-null ethtool_ops. Test only
dev->ethtool_ops->get_link in both places where we care.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct a mistake made in the previous commit due to reckless
copy-and-pasting.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This pull request is intended for 3.8...
This includes a Bluetooth pull. Gustavo says:
"A few more patches to 3.8, I hope they can still make it to mainline!
The most important ones are the socket option for the SCO protocol to allow
accept/refuse new connections from userspace. Other than that I added some
fixes and Andrei did more AMP work."
Also, a mac80211 pull. Johannes says:
"If you think there's any chance this might make it still, please pull my
mac80211-next tree (per below). This contains a relatively large number
of fixes to the previous code, as well as a few small features:
* VHT association in mac80211
* some new debugfs files
* P2P GO powersave configuration
* masked MAC address verification
The biggest patch is probably the BSS struct changes to use RCU for
their IE buffers to fix potential races. I've not tagged this for stable
because it's pretty invasive and nobody has ever seen any bugs in this
area as far as I know."
Several other drivers get some attention, including ath9k, brcmfmac,
brcmsmac, and a number of others. Also, Hauke gives us a series that
improves watchdog support for the bcma and ssb busses. Finally, Bill
Pemberton delivers a group of "remove __dev* attributes" for wireless
drivers -- these generate some "section mismatch" warnings, but Greg
K-H assures me that they will disappear by the time -rc1 is released.
This also includes a pull of the wireless tree to avoid merge
conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extracting a part of the SDHCI card tasklet into a .card_event()
implementation allows SDHCI hosts to use generic card-detection
services, e.g. the GPIO slot function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The slot-gpio API provides a generic card-detection handler. To support a
wider range of hosts it has to call the host's card-event callback, if
implemented. Also increase the debounce interval to 200ms to match the
SDHCI driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
'sc' is used only when CONFIG_PM_RUNTIME is defined. Hence define it
conditionally.
Silences the following warning:
drivers/mmc/host/sdhci-s3c.c: In function ‘sdhci_s3c_notify_change’:
drivers/mmc/host/sdhci-s3c.c:378:20: warning: unused variable ‘sc’ [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On error, the error code from tun_flow_init() is lost inside
tun_set_iff(), this patch fixes this by assigning the tun_flow_init()
error code to the "err" variable which is returned by
the tun_flow_init() function on error.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The get_clock() of the chelsio driver clashes with the s390 one.
The chelsio helper reads a timespec via ktime just to convert it
back to ktime. I can see no different outcome from calling
ktime_get directly.
Remove the get_clock and use ktime_get directly.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the driver is configured to operate with a certain
link configuration which differs from the link's configuration during
boot from SAN - this would cause the driver to flap the link.
Said flap may be missed by specific switches, causing dcbx convergence
to be too long and boot sequence to fail. Convergence is longer because
switch ignores new dcbx packets due to counters mismatch, as only host
side reset the counters due to the link flap.
This patch causes the driver to ignore user's initial configuration during
boot from SAN, and continues with the existing link configuration.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A SMSC PHY in power down mode can't be used.
If a SMSC PHY is in this mode in the config_init
stage, the mode "all capable" is set. So the PHY
could then be used.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using symbol_get(), cnic can now directly call the cnic_probe
functions in struct bnx2x and struct bnx2. symbol_get() is not reliable
as it fails when the module is still initializing.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by removing duplicate symbols and removing some redundant code.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with BNX2_ prefix for namespace consistency. Currently, these macro names
conflict with similar macros in bnx2x.h, preventing the cnic driver from
including both bnx2.h and bnx2x.h. Including bnx2x.h in cnic.c will remove
many redundant definitions and simplify the interface.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using a few temporary variables, smatch can track
what's happening and stops complaining that we access
beyond the tid_data array.
This also makes the generated code a bit smaller, so
it's a win all around.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
6e20a0a429
(gpio: pcf857x: enable gpio_to_irq() support)
added gpio_to_irq() support on pcf857x driver,
but it used pdata->irq.
This patch modifies driver to use client->irq instead of it.
It modifies kzm9g board platform settings,
and device probe information too.
This patch is tested on kzm9g board
Reported-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Given a small change to igb_init_interrupt_scheme() the function fits
igb_request_irq() for MSI/legacy interrupts initialization as well, instead of
duplicating most of its code there.
Also adding a missing igb_configure() to igb_request_irq() for MSI fallback
to work properly.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540's internal thermal sensor should not be enabled for all devices, but
only those devices which enable it in the NVM image. It is expected that
actively cooled devices will have it enabled, but passively cooled devices might
not want it enabled. This is due to passively cooled devices operating very near
the thermal threshold, sometimes within the margin of error of the thermal
sensor. Thus these devices may not be good candidates for using the thermal
sensor.
This patch uses the enabled bit in the FWSM register to check whether we should
be enabling the thermal sensor, and only sets the THERMAL_SENSOR_CAPABLE flag
for those devices which have it enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the normal kernel test instead of a module specific one.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the device is taken down in stop_hw, call reset_ict
from there too.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New transports may handle it internally for better performance.
Also move the tracing inside PRPH access which will make the
output more readable:
iwlwifi_dev_ioread_prph32: Read 0x0 from SCD_AGGR_SEL (32-bit)
instead of the corresponding accesses to HBUS_TARG_PRPH_*.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we will have several forms of NVM (EEPROM, OTP, etc.)
and they will have different layouts, make the parsed data
more generic. This allows functional code to be independent
of a specific layout.
Also change some variables and function names from having
"eeprom" to "nvm" in their name.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: users@rt2x00.serialmonkey.com (moderated for non-subscribers)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Dan Williams <dcbw@redhat.com>
Cc: libertas-dev@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: brcm80211-dev-list@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: b43-dev@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register the watchdog driver to the system if it is a SoC. Using the
watchdog on a non SoC device, like a PCI card, will make the PCI
card die when the timeout expired, but starting it again is not
supported by ssb.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, add a method converting ms to ticks before setting the watchdog
register. Return the ticks or millisecond the timer was set to in case
the provided value was bigger than the max allowed value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent the watchdog register on the extif core to be set to a too
high value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, which is depending on the SoC type and the clock.
Calculate the number of ticks per millisecond and provide two functions
for the watchdog driver. Also return the ticks or millisecond the timer
was set to in case the provided value was bigger than the max allowed
value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some ssb based devices have a PMU and the PMU watchdog register should
be used instead of the register in the chip common part, if the device
has a PMU. This patch also calculates the maximal number the watchdog
could be set to.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there is a PMU in the device, get the alp clock from that part and
do not assume 20000000.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register the watchdog driver to the system if this is a SoC. Using the
watchdog on a non SoC device, like a PCIe card, will make the PCIe
card die when the timeout expired, but starting it again is not
supported by bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, which is depending on the SoC type and the clock.
Calculate the number of ticks per millisecond and provide two functions
for the watchdog driver. Also return the ticks or millisecond the timer
was set to in case the provided value was bigger than the max allowed
value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly all bcma based devices have a PMU and the PMU watchdog should be
used and not the old one in chip common. This patch also calculates the
maximal number the watchdog could be set to.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For devices without a PMU the alp clock is always 20000000.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have assinged error code to 'ret' when get auth from some
option is not supported but never used it, but we'd better return
the error code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise rt2500* triggers a warning in cfg80211, from net/wireless/core.c:
/* Combinations with just one interface aren't real */
if (WARN_ON(c->max_interfaces < 2))
This was introduced in commit 55d2e9da74:
rt2x00: Replace open coded interface checking with interface combinations.
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@vger.kernel.org [3.7+]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter reported that smatch detected a potential
problem with the code [1]:
drivers/net/wireless/ath/carl9170/tx.c:1488 carl9170_op_tx()
error: we previously assumed 'sta' could be null (see line 1482)
drivers/net/wireless/ath/carl9170/tx.c
1482 if (sta) {
^^^^^ New check.
[...]
1485 }
1487 if (info->flags & IEEE80211_TX_CTL_AMPDU) {
1488 run = carl9170_tx_ampdu_queue(ar, sta, skb);
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Old dereference of "sta" inside the call to carl9170_tx_ampdu_queue().
A range of solutions have been discussed in [2] and
we agreed on the following: "
> we might as well add a comment to carl9170_tx_ampdu_queue
> and explain the situation [in a way that's obvious to a
> human reader]. This way we can save the "if"... which is
> a small win since carl9170_op_tx is sort of a hot-path.
Putting a comment there is fine. Without the comment
it's easy for a human reader to get confused why the
check is there. So long as humans can read the code,
that's all that matters."
[1] <http://www.spinics.net/lists/linux-wireless/msg94526.html>
[2] <http://www.spinics.net/lists/linux-kernel-janitors/msg14953.html>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It fixes a potential crash when receiving an LLCP HDLC frame acking a frame
that is not the last sent one. In that case we may dereference an already
freed pointer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQt0kOAAoJEIqAPN1PVmxKpxoQAJwbaylVz/miDjJLPekDhQ+z
YkDmtBWJD9oy5GS/EUZPRIIEj+Ftaao0lAJDP4couYiZPQbrRBY1llBOxcIzkCqR
fsAaD8jnPRGHwWtdqws8txFePh4Hn5WXHmJbcsOyVGt4gmy/xT06gme4p3VdIQIP
XIkbss5mz29OdQwOLHzH4zva7JtZm9XOEWYWAbbFsrgNxXLBt7GhfF92TT29K4Wt
UxFalwMYrpowY+BCBWzS1H31wVvNaDcsBRSO0hqvUZb7DgWM2b25B4Xnx3LiyLHR
9A17LWYso6mRhQPSqqhT5wWlKNT1G5VKZ8/X0i69ZLXi040NzpvMbvq41RhM9SwN
bmWZNUWGrGkQJY6VPAdXeraoSmSNwOD4KnLXNV8rWmmg+NSzf8ZPWNCcxNEdIMnK
oBe7vvk3j5z6QGNPeMB5C3hfpyRwyvRTqC9O5/dO7DOYD0lb0O6tuj1/MzhsOR2L
pzBUjkvfJBA0FXdeDD7gFwR062uJZL4hinRpFPj4qTtFWPYypirWdnRpCSZbvbeW
ZB3k7+8oNOGhn1TYPUmWsN1GNk2EJ4ZSpAf7BUI5Vb1KmcSpUQA6BN6yPlS/WQ4U
eowwW+sUYPu5LixMCO/LtuUllJ/RCTzdQJH6j/hZlEqmfYs00emKNa08tk15XjGF
zn2jXJjTykbYiVRirBR5
=tpAI
-----END PGP SIGNATURE-----
Merge tag 'nfc-fixes-3.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-3.0
This is an NFC LLCP fix for 3.7 and contains only one patch.
It fixes a potential crash when receiving an LLCP HDLC frame acking a frame
that is not the last sent one. In that case we may dereference an already
freed pointer.
The Ricoh SDHCI controllers support Highspeed clocks as evident from
the ricoh_mmc_probe_slot() settings. Hence, SDHCI_CAN_DO_HISPD needs
to be set to enable SDIO client drivers to set/enable high speed clock
settings
Signed-off-by: Madhvapathi Sriram <Madhvapathi.Sriram@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This commit taken from Rabeeh's Cubox kernel and re-worked for DT;
Sebastian Hasselbrath is believed to be the original author.
Some Cuboxes require a GPIO for card detection; this implements the
optional GPIO support for card detection. This GPIO is logic 0 for
card inserted.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
We need to use the two-stage initialization for sdhci-pltfm if we're
going to do anything extra at initialization time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use devm_clk_get() rather than clk_get() to make cleanup paths more simple.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
A-003500: False ADMA Error might be reported when ADMA is used for
multiple block read command with Stop at Block Gap. If PROCTL[SABGREQ]
is set when the particular block's data is received by the System side
logic before entire block (with CRC) data is received by the SD side
logic, and also if ADMA descriptor line is fetched at the same time,
then DMA engine might report false ADMA error. eSDHC might not be able
to Continue (PROCTL[CREQ]=1) after Stop at Block Gap.
This issue will impact the eSDHC IP VVN2.3.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ctype is using 1-bit buswidth mode by default.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
To ensure the stable clock need to enable before set the
DW_MMC_CARD_NEED_INIT flag. If set DW_MMC_CARD_NEED_INIT flag,
wait for 80-clock before first command after power-up.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If "caps2" host capabilities does not indicate support for MMC
HS200, don't allow clock speeds >52MHz. Currently, for MMC, the
clock speed is set to the lesser of the max speed the eMMC module
supports (card->ext_csd.hs_max_dtr) or the max base clock of the
host controller (host->f_max based on BASE_CLK_FREQ in the host
CAPS register). This means that a host controller that doesn't
support HS200 mode but has a base clock of 100MHz and an eMMC module
that supports HS200 speeds will end up using a 100MHz clock.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use managed device resource functions for easy handling.
This makes driver simpler in the routine of error and exit.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMCIF only uses one clock, all ARM and SuperH platforms register MMCIF
clock lookup entries with no connection ID, hence it can be dropped in
the driver too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHI only uses one clock, all ARM and SuperH platform register SDHI clock
lookup entries with no connection ID, hence it can be dropped in the
driver too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
During its probing the SDHI driver prints out the clock frequency, but
does it wrongly, always reporting 0Hz. Use the MMC host frequency value
to fix this issue.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use devm_kzalloc, devm_gpio_request_one and devm_request_irq to make
cleanup path simpler.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.
However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available, so attempting to
switch to the 1.8v level will result in a situation that cannot be
recovered from without physically replugging the SD card.
Add a device tree flag that can be used on systems like these,
and hook it up to the equivalent SDHCI quirk.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.
However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available.
Add a quirk so that systems such as this one can override disable
1.8v support, adding support for UHS-I cards (by running them at
3.3v).
This avoids a problem where the system would first try to run the
card at 1.8v, fail, and then not be able to fully reset the card
to retry at the normal 3.3v voltage.
This is more appropriate than using the MISSING_CAPS quirk, which
is intended for cases where the SDHCI controller is actually lying
about its capabilities, and would force us to somehow override both
caps words from another source.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend methods provided by SDIO drivers are not supposed to be called by
the PM core. Instead, when the SDIO core gets to suspend a device's
ancestor, it calls the device driver's suspend routine. However, the PM
core executes suspend callback routines directly for device drivers whose
bus types don't provide suspend callbacks. In consequece, because the
SDIO bus type doesn't provide a suspend callback, the SDIO drivers'
suspend routines will be executed by the PM core (which shouldn't
happen).
To prevent this from happening, add empty system suspend/resume callbacks
for the SDIO bus type.
An analogous change had been made already by commit (e841a7c mmc: sdio:
Use empty system suspend/resume callbacks at the bus level), but then it
was reverted inadvertently by commit (d8e2ac3 mmc: sdio: Fix PM_SLEEP
related build warnings) that attempted to fix build warnings introduced
by commit e841a7c.
Reported-by: NeilBrown <neilb@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add missing usb_put_dev on failure path in vub300_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Marina Makienko <makienko@ispras.ru>
Signed-off-by: Chris Ball <cjb@laptop.org>
clk_{un}prepare is mandatory for platforms using common clock
framework. Because for SPEAr we don't do anything in clk_{un}prepare()
calls, just call them once in probe/remove.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SPEAr sdhci driver expects the clock to be set to 50 MHz for proper
functioning. This patch sets clk to 50 MHz in probe.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for pin configuration using pinctrl subsystem
to the sdhci-s3c driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The set of GPIO pins used by sdhci-s3c driver varies between
configurations, such as card detect method, pinctrl availability, etc.
This overly complicates the code requesting and freeing GPIO pins, which
must check which pins are used, when freeing them.
This patch modifies the sdhci-s3c driver to use devm_gpio_request to
free requested pins automatically after unbinding the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The IP versions older than 2.3 didn't support commands with busy
response which expect the TC bit set. But after the VVN2.3, eSDHC
IP has supported it.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The third argument for of_get_property() is a pointer, hence pass
NULL instead of 0.
Fixes the following sparse warning:
sdhci-s3c.c:452:48: warning: Using plain integer as NULL pointer
sdhci-s3c.c:457:52: warning: Using plain integer as NULL pointer
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Define the most frequently used bitmasks of the Interrupt Enable /
Interrupt Status register with consistent naming ( with _EN suffix).
Use meaningful concatenation of bitfields for INT_EN_MASK, which shows
which interrupts are enabled by default. No functional changes.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fatal errors for the driver are not reported when just error debug
is enabled. Convert selected dev_dbg to dev_err for accurate error
reporting.
Reported-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
prepare() is supposed to prevent new children from being registered.
On the MMC subsystem, children (new cards) registration starts with
the card detect IRQ.
Move card detect IRQ disabling to prepare() so that no new cards
will be registered while we're trying to suspend.
Likewise, move card detect IRQ enabling to complete() so we only
try to register new children after our MMC IP is back up.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.
From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation):
The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.
There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
capabilities register and
- MMC/SD clock coming out of controller > 25MHz
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Update error code to cmd->error for commands with response_busy and no data.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Avoid soft reset of command internal state machine on data errors.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ae4bf788ee ("mmc: omap_hsmmc: consolidate error report handling of HSMMC
IRQ") sets both end_cmd and end_trans to 1.
Setting end_cmd to 1 for Data Timeout/CRC leads to NULL pointer dereference of
host->cmd as the command complete has previously been handled.
Set end_cmd only in case of command Timeout/CRC.
Moreover host->cmd->error should not be updated on data error case, only
host->data->error needs to be updated.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add dt-based retrieval of host sdio pm capabilities. Based on
the dt based discovery do a bus init in the resume function.
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add support for optional pm capabilities such as MMC_PM_KEEP_POWER
and MMC_PM_WAKE_SDIO_IRQ.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For regulator vmmc/vmmcq, use voltage range as below
3.3v/3.0v: (2.7v, 3.6v)
1.8v: (1.7v, 1.95v)
Original code uses the precise value which may fail in regulator
driver if it does NOT support the precise voltage.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the SD/MMC host controller found
on Wondermedia 8xxx series SoCs, currently supported under
arm/arch-vt8500.
A binding document is also included, based on mmc.txt with
additional properties.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
RPMB partition is accessing though /dev/block/mmcXrpmb device
User callers can read and write entire data frame(s) as defined
by JEDEC Standard JESD84-A441, using standard IOCTL interface.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide support for automatically sending Set Block Count
(CMD23) messages. Used at least for RPMB support.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not scan rpmb partitions for "soft" partitions, since the rpmb
partition contains protected data. Silences the following message
during boot:
mmcblkXRPMB: unknown partition table
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Following JEDEC standard, if the mmc supports RPMB partition,
a new interface is created and exposed via /dev/block.
Users will be able to access RPMB partition using standard
mmc IOCTL commands.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable the quirk SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN since
SD_CAPABILITIES_1[15:8](BASE_FREQ) can't get correct base clock value.
It returns a fixed pre-set value like 200 on some sdhci-pxav3 based
platforms like MMP3 while return 0 on the other sdhci-pxav3 based
platforms. So we enable the quirk and get the base clock via function
get_max_clock. Also add get_max_clock.
Reported-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Philip Rakity <prakity@Marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are discrepancies with regards to how MMC capabilities
are carried throughout the subsystem. Let's standardise them
to eliminate any confusion.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
All MXS users have been converted to device tree and the board files have
been removed.
No need to keep platform data in the driver.
Also move bus_width declaration in the beggining of mxs_mmc_probe() to
avoid: 'warning: ISO C90 forbids mixed declarations and code'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Before this patch, we always used only single sg entry for SDIO transfer.
This patch switches to using multiple sg entries. In the case of dwmci,
it supports only up to 4KB size per single sg entry. So if we want to
transfer more than 4KB, we should send more than 1 command.
When we tested before applying this patch, it took around 335 us for
5K(5120) bytes transfer with dwmci controller. After applying this patch,
it takes 242 us for 5K bytes. So this patch makes around 38% performance
improvement for 5K bytes transfer. If the transfer size is bigger, then
the performance improvement ratio will be increased.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are infinite loops in the mmc code that can be caused by bad
hardware. The code will loop forever if the device never comes back
from program mode, R1_STATE_PRG, and it is not ready for data,
R1_READY_FOR_DATA.
A long timeout is added to prevent the code from looping forever.
The timeout will occur if the device never comes back from program
state or the device never becomes ready for data.
It's not clear whether the timeout will do more than log a pr_err()
and then start a fresh hang all over again. We may need to extend
this patch later to perform some kind of reset of the device (is
that possible?) or rejection of new I/O to the device.
Signed-off-by: Trey Ramsay <tramsay@linux.vnet.ibm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The patch "dw_mmc: fix multiple drv_data NULL dereferences" has
unfortunately clashed with my "mmc: dw_mmc: constify dw_mci_idmac_ops
in exynos back-end" patch, causing new warnings to appear.
This should hopefully fix the issue for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The at91-mci driver is not needed anymore since the atmel-mci driver now
supports all Atmel devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC debounce clock is applicable only for omap2430, warning message gets
printed when enable fails for debounce clock. Remove the get debounce clock
failure message as it is noisy for other platforms.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Maximum bus frequency can be limited by external circuitry like level
shifters etc. Allow passing this value from DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This allows DT-driven board to set up the pin mux only when the driver
is in use.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a SD card is initialized some data transfers of 64 and 8 bytes
are issued. It seems the DMA has some problems dealing with these kind
of "short" transfers, leading sometimes to the SD card not being detected.
In order to solve this problem, do not use DMA for transfer sizes lower
than the sector size.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since v3.2 we have nice macro to define the platform driver's init and exit
calls. This patch simplifies the dw_mmc platform driver by using that macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Girish K S <girish.shivanajappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In case both 'req' and 'mq->mqrq_prev->req' are null, there is no request
to be processed. That means there is no need to switch buffer.
Switching buffer is required only after finishing 'issue_fn'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some systems, e.g., kzm9g, MMCIF interfaces can produce spurious
interrupts without any active request. To prevent the Oops, that results
in such cases, don't dereference the mmc request pointer until we make
sure, that we are indeed processing such a request.
Reported-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Cc: stable@vger.kernel.org
Signed-off-by: Chris Ball <cjb@laptop.org>
The vmmc regulator enable in sdhci_add_host is NOT necessary since
it can be enabled during mmc_power_up by function mmc_regulator_set_ocr.
And this extra enable will make regulator_enable/regulator_disable
unbalanced. Consequently, vmmc can't be disabled during mmc_power_off.
Also, if the vqmmc regulator exists, it should be enabled regardless it
support 1.8v or not.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 8464dd52d3, which was a misapplied debugging
version of the patch, not the final patch itself.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: stable@vger.kernel.org
2abeb5c5de ("Add clk_(enable/disable) in runtime suspend/resume")
added the capability to stop the clocks when the device is runtime
suspended, but forgot to handle the case of the card-detect using
an external gpio.
Therefore in the case that runtime-pm is enabled, start the io-clock
when a card is inserted and stop it again once it is removed.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The variable se_sess is initialized but never used
otherwise, so remove the unused variable.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Zero copy TX has been around for a while now.
We seem to be down to eliminating theoretical bugs
and performance tuning at this point:
it's probably time to enable it by default so that
most users get the benefit.
Keep the flag around meanwhile so users can experiment
with disabling this if they experience regressions.
I expect that we will remove it in the future.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For short packets zerocopy mode adds overhead
of managing heads which isn't necessary: we
could simly update used ring directly
same as with zerocopy disabled.
Things seem to run a bit faster if we detect
and bypass head management when zcopy isn't used.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When memory map changes, we need to flush outstanding
DMAs as they might in theory reference old memory addresses.
To do this simply stop initiating new DMAs
and wait for ubufs ref count to drop to 0.
Afterwards reset the count back to 1.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vring changes already do a flush internally where appropriate, so we do
not need a second flush.
It's currently not very expensive but a follow-up patch makes flush more
heavy-weight, so remove the extra flush here to avoid regressing
performance if call or kick fds are changed on data path.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is really a 3-bit field, not a single bit,
so declare a mask and shift. Also fix hwsim, it
advertises the maximum possible.
While at it reindent all the defines using tabs
instead of spaces.
Change-Id: I7cd81c0d72f76deb5010aba5bfa3dd312006e898
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the initiator and target try to close the connection at about the same
time, there is a race condition in the termination sequence for bnx2x.
Fix the problem by waiting for the remote termination to complete before
deleting the Connection ID. This will prevent the firmware assert.
Update version to 2.5.15.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without the reset, reloading the cnic driver can cause the iSCSI
Event Queue to be out of sync with the driver and cause intermittent
crash.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added functions for ack_interrupt and config_intr. Tested on an mpc5200b
powerpc board.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- convert remaining htonl/ntohl +__raw_read/__raw_writel to
swab32 + readl/writel
- add missing __iomem qualifier in myri10ge_open()
- fix dubious: x & !y warning by switching from logical to bitwise not
The swab32 conversion fixes a bug in myri10ge_led() where
big-endian machines would write the wrong pattern.
The only remaining warning (lock context imbalance) is due to
the use of __netif_tx_trylock(), and cannot easily be fixed.
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3com driver for 3c59x requires ioport_map. Since not all
architectures support IO port mapping make 3c59x dependent on HAS_IOPORT.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set chan_mux[DA9055_ADC_ADCIN3] = DA9055_ADC_MUX_ADCIN3.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is the HWMON patch for DA9055 PMIC and has got dependency on the
DA9055 MFD core.
This patch monitors the DA9055 PMIC's ADC channels vddout, junction temperature
and auxiliary channels.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: Dropped __devinit, __devexit, __devexit_p]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since N4xx, N5xx, D4xx, and D5xx are now reliably detected using the model ID
and the stepping/mask, drop the respective entries from tjmax_table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Make the code easier to extend and easier to adjust by using a model table
listing CPU models, stepping/mask, and associated TjMax.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
So far, we use the NM10 Express Chipset PCI chip ID to detect TjMax for
Atom CPUs with model 0x1c. As it turns out, we can use the CPU stepping
(x86_mask) for the same purpose; stepping is 10 for all model 0x1c CPUs
with TjMax of 100 degrees C. This was verified by checking the output of
/proc/cpuinfo for the respective CPUs (D4xx, D5xx, N4xx, N5xx).
Other CPUs currently covered by the same code (Exx, Z6xx, Z2460) are not
supported by the NM10 Express Chipset. Most of those CPUs have TjMax of 90
degrees C, except for E6xxT models which have a TjMax of 110 degrees C.
E6xxT CPUs can however not be detected by software.
Calculate TjMax for Atom CPUs as follows. Note that the listed values are not
correct in some cases (230, 330). tjmax_table is used for those to override
the default values.
ID Stepping TjMax Models
0x1c 10 100 D4xx, N4xx, D5xx, N5xx
0x1c not 10 90 Z5xx, N2xx, 230, 330, others
0x26 - 90 Atom Tunnel Creek (Exx),
Lincroft (Z6xx)
0x27 - 90 Atom Medfield (Z2460)
0x36 - 100 Atom Cedar Trail (N2xxx, D2xxx)
Also drop the module dependency on PCI.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Signed-off-by: Guillaume Roguez <guillaume.roguez@savoirfairelinux.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As there is no reliable way to identify the chip, it is preferable to
remove the detect callback, to avoid misdetection.
Module parameters are not worth it here, so let's get rid of them and
add an ads7828_platform_data structure instead.
Clean the code by removing unused macros, fixing coding style issues,
avoiding function prototypes and using convenient macros such as
module_i2c_driver().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add family 16h PCI ID to AMD's power driver to allow it report
power consumption on these processors.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We want to use the virtual counter at EL0, as the physical counter
may not track the current clocksource for guests running under a
hypervisor.
This patch updates the vdso and generic timer driver to use the virtual
counter. The kernel EL2 entry code is also updated to ensure that the
virtual offset is initialised to zero.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This revert:
commit be03d4a45c
Author: Andreas Hartmann <andihartmann@01019freenet.de>
Date: Tue Apr 17 00:25:28 2012 +0200
rt2x00: Don't let mac80211 send a BAR when an AMPDU subframe fails
To fix problem workaround by above commit use
IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL flag (see change log for
"mac80211: introduce IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL" patch).
Resolve: https://bugzilla.kernel.org/show_bug.cgi?id=42828
Bisected-by: Francisco Pina Martins <f.pinamartins@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Or else the laptop will boot with a dimmed screen.
References: https://bugzilla.kernel.org/show_bug.cgi?id=51141
Tested-by: Stefan Nagy <public@stefan-nagy.at>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When system enters power off, the _PSW of Lid device is enabled.
But this may cause the system to reboot instead of power off.
A proper way to fix this is to always disable lid wakeup capability for S5.
References: https://bugzilla.kernel.org/show_bug.cgi?id=35262
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This fixes a bit error in the U8500 clock implementation: the
unused p2_pclk12 registered at bit 12 in periphereral group 6
was defined as using bit 11 rather than bit 12.
When walking over and disabling the unused clocks in the tree
at late init time, p2_pclk12 was disabled, by effectively
clearing the but for p2_pclk11 instead of bit 12 as it should
have, thus disabling gpio block 6 and 7.
Reported-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Philippe Begnic <philippe.begnic@st.com>
Cc: stable@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use for_each_pci_dev to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add qlcnic prefix to qlcnic driver module parameters.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor 82xx driver to support new adapter
Update routines to support variable number of NIC partitions
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor 82xx driver to support new adapter
Update PCI and hardware access routines
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move HW specific data to a seperate structure as part of
refactoring 82xx adapter driver.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 82xx adapter ID check before 82xx specific operations as part of
refactoring the driver to enable support for new adapter.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the hardware timestamping as described in
Documentation/networking/timestamping.txt
Update version to 3.128.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the SIOCSHWTSTAMP ioctl as described in
Documentation/networking/timestamping.txt
[Removed HWTSTAMP_FILTER_ALL handling by returning -ERANGE based on input
from Richard Cochran.]
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ptp_caps structure, ptp api implementation,
reference clock read and register/unregister functions. All the basic
clock operations as described in Documentation/ptp/ptp.txt are
supported.
Frequency adjustment is performed using hardware with a 24 bit
accumulator and a programmable correction value. On each clk, the
correction value gets added to the accumulator and when it overflows,
the time counter is incremented/decremented and the accumulator reset.
So conversion from ppb to correction value is
ppb * (1 << 24) / 1000000000
[Re-organized to put the ptp_clock_info struct declaration in one patch,
added ptp_clock_info.name, and added locking to tg3_ptp_adjtime() based
on input from Richard Cochran.]
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to write the reference clock. If a chip reset is
performed, the hwclock is reinitialized with the adjusted kernel time
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every caller holds tp->lock when calling tg3_netif_start() except
tg3_io_resume(). Fix it so that it is all consistent. The subsequent
PTP patches add tg3_ptp_resume() to tg3_netif_start() and the tp->lock
is required.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
code:
1. The UBI background thread got stuck when a bit-flip happened because free
LEBs was not removed from the "free" tree when we started using it.
2. I/O debugging checks did not work because we called a sleeping function in
atomic context.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fs+0
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.7-rc9' of git://git.infradead.org/linux-ubi
Pull UBI changes from Artem Bityutskiy:
"Fixes for 2 brown-paperbag bugs introduced this merge window by the
fastmap code:
1. The UBI background thread got stuck when a bit-flip happened
because free LEBs was not removed from the "free" tree when we
started using it.
2. I/O debugging checks did not work because we called a sleeping
function in atomic context."
* tag 'upstream-3.7-rc9' of git://git.infradead.org/linux-ubi:
UBI: dont call ubi_self_check_all_ff() in __wl_get_peb()
UBI: remove PEB from free tree in get_peb_for_wl()
Pull workqueue fixes from Tejun Heo:
"So, safe fixes my ass.
Commit 8852aac25e ("workqueue: mod_delayed_work_on() shouldn't queue
timer on 0 delay") had the side-effect of performing delayed_work
sanity checks even when @delay is 0, which should be fine for any sane
use cases.
Unfortunately, megaraid was being overly ingenious. It seemingly
wanted to use cancel_delayed_work_sync() before cancel_work_sync() was
introduced, but didn't want to waste the space for full delayed_work
as it was only going to use 0 @delay. So, it only allocated space for
struct work_struct and then cast it to struct delayed_work and passed
it into delayed_work functions - truly awesome engineering tradeoff to
save some bytes.
Xiaotian fixed it by making megraid allocate full delayed_work for
now. It should be converted to use work_struct and cancel_work_sync()
but I think we better do that after 3.7.
I added another commit to change BUG_ON()s in __queue_delayed_work()
to WARN_ON_ONCE()s so that the kernel doesn't crash even if there are
more such abuses."
* 'for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: convert BUG_ON()s in __queue_delayed_work() to WARN_ON_ONCE()s
megaraid: fix BUG_ON() from incorrect use of delayed work
megaraid use INIT_WORK to declare a hotplug_work, but cast the
hotplug_work from work_struct to delayed_work and
schedule_delayed_work on it. This is very dangerous, as other part of
delayed_work might be kernel memories allocated by others.
With commit 8852aac ("workqueue: mod_delayed_work_on() shouldn't queue
timer on 0 delay"), schedule_delayed_work() will check dwork->timer
before queue_work even when @delay is 0, this causes megaraid code to
hit the BUG_ON() in workqueue code. Change megaraid code to use
delayed work.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
As ubi_self_check_all_ff() might sleep we are not allowed
to call it from atomic context.
For now we call it only from ubi_wl_get_peb().
There are some code paths where it would also make sense,
but these paths are currently atomic and only enabled
when fastmap is used.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
If UBI is built without fastmap, get_peb_for_wl() has to
remove the PEB manially from the free tree.
Otherwise the requested PEB lives in two trees.
Reported-by: Zach Sadecki <zsadecki@itwatchdogs.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
* acpi-general:
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
Use for_each_pci_dev to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[Boris: cleanup comments and drop loop brackets]
Signed-off-by: Borislav Petkov <bp@alien8.de>
This is a series of patches that remove the dev* attributes for all
networking drivers, with the exception of wireless drivers, those are in
a different branch.
Use of __devinit, __devexit_p, __devinitdata, __devinitconst, and
__devexit are no longer needed since CONFIG_HOTPLUG is being removed as
an option.
Note, there are some devinit compiler section mismatch warnings due to
this series, but they are fixed up when merged with my driver-next
branch, which fixes the PCI device id warnings, and removes the modpost
detection, as it's no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlC9COEACgkQMUfUDdst+ykOEgCeKZsrtKrbjMFM5jEROqnk33FI
SwEAoMSZWFJ7M1/27FGRkylmmypWXi/p
=HH3A
-----END PGP SIGNATURE-----
Merge tag 'dev_removal' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/net-next
Networking: Remove __dev* markings from the networking drivers
This is a series of patches that remove the dev* attributes for all
networking drivers, with the exception of wireless drivers, those are in
a different branch.
Use of __devinit, __devexit_p, __devinitdata, __devinitconst, and
__devexit are no longer needed since CONFIG_HOTPLUG is being removed as
an option.
Note, there are some devinit compiler section mismatch warnings due to
this series, but they are fixed up when merged with my driver-next
branch, which fixes the PCI device id warnings, and removes the modpost
detection, as it's no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Historically tun supported two modes of operation:
- in default mode, a small number of packets would get queued
at the device, the rest would be queued in qdisc
- in one queue mode, all packets would get queued at the device
This might have made sense up to a point where we made the
queue depth for both modes the same and set it to
a huge value (500) so unless the consumer
is stuck the chance of losing packets is small.
Thus in practice both modes behave the same, but the
default mode has some problems:
- if packets are never consumed, fragments are never orphaned
which cases a DOS for sender using zero copy transmit
- overrun errors are hard to diagnose: fifo error is incremented
only once so you can not distinguish between
userspace that is stuck and a transient failure,
tcpdump on the device does not show any traffic
Userspace solves this simply by enabling IFF_ONE_QUEUE
but there seems to be little point in not doing the
right thing for everyone, by default.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Kevin Curtis <kevin.curtis@farsite.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: VMware, Inc. <pv-drivers@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: linux-hippi@sunsite.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
Cc: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: cbe-oss-dev@lists.ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
