The data from the sprom consists of u16 values stored in little
endian notation over which a crc8 was determined. To validate this
the buffer needed to be converted for big-endian systems. Reading
the sprom data is now done per byte so conversion is only done
after a successful crc8 check.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The n-phy requested some srom variables that are no longer needed
and consequently not present in the srom revision 8 and higher that
this driver support. This code has been removed from the n-phy.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case the hardware crashes, a reinitialization internal to the driver
was performed. Since Mac80211 must be in the know of such an event as
well, ieee80211_restart_hw() is now called.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct brcmf_scan_results contained a 1 element array, but in reality
the number of scan results can be 0 or more, as indicated by the
count field in the same struct. Array has be redefined to be 0 elements
length to indicate the array is purely for reference.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved function to where it is called and made it more readable.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Made code more readable.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac driver registered with mac80211 with HT capability info
set to 40MHz intolerant. This cause any other station on the channel
to be forced to use 20MHz. This flag has been removed.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removed defines from aiutils.h also present in soc.h.
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch added a check to get_key() but missed a couple
other places which need range checks.
The problem here is that wifi drivers have different numbers of keys.
The lower levels assume that they can have up to 4 default keys and
2 management keys but this driver only has the default keys so we
could go past the end of the ->keys[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wifi drivers can have up to 6 keys but the rndis_wlan only has 4 so
it needs to have its own checks to make sure we don't go out of
bounds. The add_key() function already checks but I added some
checks to del_key() and set_default_key().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code here treats very large values of "limit" as less than
MAX_POWER_RATE because of the cast to int. We should do the compare
as u32 instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When userspace requested that a scan not be
done with CCK rates, use 6 Mbps. This is used
for example for P2P scanning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwl_alloc_all routine is only called once. Delete the argument
and print an error in the calling routine if needed.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the HW rev. for both 105 and 135 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device tracing routines only use the priv pointer as an opaque
value. Change from a typed iwl_priv pointer to a null pointer and
eliminate the need to include iwl_priv.h. CMD_ASYNC is defined in
iwl_shared.h which is the only reason it is included.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WoWLAN API changed due to netdetect and
we now have a more generic "D3 configuration"
command that enables the sysassert & rfkill
wakeup triggers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A minor fix for the check that verifies that all given SSIDs (in req) exist
in the filters (the match sets)
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If kmemdup() fails we leak the memory allocated to bss_desc.
This patch fixes the leak.
I also removed the pointless default assignment of 'NULL' to 'bss_desc'
while I was there anyway.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Though it's unlikely, di may be null, so we can't dereference
di->dma.dmactrlflags until we've checked it.
Move this de-reference after the check, and adjust the error
message to not require de-referencing di.
This is based upon Julia's original patch:
<1319846297-2985-2-git-send-email-julia@diku.dk>
Reported-by: Julia Lawall <julia@diku.dk>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes PHY transmission errors reported on some LP-PHY and HT-PHY
cards. For LP-PHY they were quite rare and not really noticable. On
HT-PHY they were critical, OFDM rates were not available at all.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Perform "echo test" when cmd queue stuck detected, somethime it will cause
calltrace. I am not sure how to fix it yet, just remove the action now until
find a better way to handle it.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver can spam the logs with "RX: Packet dropped" messages. These drops
originate from 1. a correpted PLCP, 2. decryption errors, and 3. packet
size underruns. Condition #3 logs a separate message, thus no dropped message
is needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Continue the init process even fail to enable msi
out_iounmap is no longer used, remove it
Reported-by: werner <w.landgraf@ru.ru>
Tested-by: werner <w.landgraf@ru.ru>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 2e30168b ("libertas: terminate scan when stopping interface")
adds cleanup code to lbs_eth_stop to call cfg80211_scan_done if there's
an outstanding cfg80211_scan_request. However, it assumes that the
scan request was allocated via the cfg80211 stack. Libertas has
its own internal allocation method, kept track of with
priv->internal_scan. This doesn't set scan_req->wiphy, amongst other
things, which results in hitting a BUG() when we call cfg80211_scan_done
on the request.
This provides a function to take care of the low-level scan_req cleanup
details. We simply call that to deal with finishing up scan requests.
The bug we were hitting was:
[ 964.321495] kernel BUG at net/wireless/core.h:87!
[ 964.329970] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 964.341963] pgd = dcf80000
...
[ 964.849998] 9fe0: 00000000 beb417b8 4018e280 401e822c 60000010 00000004 00000000 00000000
[ 964.865007] [<c003104c>] (__bug+0x1c/0x28) from [<c0384ffc>] (cfg80211_scan_done+0x54/0x6c)
[ 964.895324] [<c0384ffc>] (cfg80211_scan_done+0x54/0x6c) from [<bf028bac>] (lbs_eth_stop+0x10c/0x188 [libertas])
[ 964.895324] [<bf028bac>] (lbs_eth_stop+0x10c/0x188 [libertas]) from [<c03002a0>] (__dev_close_many+0x94/0xc4)
[ 964.918995] [<c03002a0>] (__dev_close_many+0x94/0xc4) from [<c030037c>] (dev_close_many+0x78/0xe0)
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the fast channel change noise floor values are being loaded
twice at init_cal and after channel_change. The commit "ath9k_hw:
Improve fast channel change for AR9003 chips" overlooked it that
caused failure to load nf while doing bgscan. This patch performs noise
floor calibration after the fast and full reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes system hang when resuming from S3 state
and lower rate sens failure issue.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the driver did not care if TX_CTL_REQ_TX_STATUS
was set on aggregated frames or not and it would silently
drop successfully sent frames if possible [much like:
"no news is good news!"].
But, TX_CTL_REQ_TX_STATUS was invented for a reason and
no tx status report should ever be dropped if it is set.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit ce407afc10 introduced regression for AR9330/AR9340
register offsets. Some of the register offsets are common
for AR9330/AR9340/AR9485 except AR9380. Fix that.
Cc: stable@kernel.org [3.1.0+]
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration during fast channel change sometimes failed
with RTT. And also restoring invalid radio retention readings
during init cal could cause failure to set the channel properly.
This patch counts the valid rtt history readings and clears
rtt mask.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My recent commits (3782c69d, 324c74a) introduced regression
for register offset selection that based on the macversion.
Not using parentheses in proper manner for ternary operator
leads to select wrong offset for the registers.
This issue was observed with AR9462 chip that immediate disconnect
after the association with the following message
ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47
after 500ms, disconnecting.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As Stanislaw pointed out, my patch
iwlagn: fix a race in the unmapping of the TFDs
solved only part of the problem. The race still exists for TFDs of
the host commands. Fix that too.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
The recent changes to only power the device when the interface up
introduced a bug: changing interface type, legal when the interface
is down, performs device I/O.
Fix this functionality by validating and recording the interface
type when the change is requested, but only applying the change
if/when the interface is brought up.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Renamed to be in sync with Marketing term and to avoid
confusion with other chip names.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR946/8x chips are 2x2 Dual band with BT support. In order
to avoid misleading with other chips and to be in sync with
marketing team's term, AR9480 is renamed as AR9462.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support the fast channel change across band switch only when there
are available of reusable cabliration results. And also observed that
doing agc control calibration on fastcc, sometimes causing calibration
timeout. Hence changing agc control to be run only on full chip reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supported calibrations of radio retention table (RTT) are
- DC offset
- Filter
- Peak detect
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To improve sensitivity for AR9480, the normal and minimum
noise floor values of both bands are updated.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: Improve fast channel change for AR9003 chips"
fixes the fast channel change issue for AR9003 chips that was
originally observed in AR9382 chip. Hence enabling fastcc support
again for 11A channel for AR9003 chips.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently Tx IQ calibration is enabled by default for all AR9003
chips. But for AR9480, the calibration status should be read from
chip after processing ini. And also the carrier leak calibration
status is checked during init cal. As the init_cal is being called
for fast channel change too, the tx_cl status only be read after
full reset. Hence moving that into process ini function.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to reuse Carrier leak calibration
during fast channel change for AR9480 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass an argument to decide whether to reuse the Tx IQ
calibration measurements or not during fast channel change.
This will be later used by MCI support for AR9480.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to reduce the overall scan time, fast channel change
should be implemented properly. This patch adds fast channel
change support across band switch or channel mode switch
instead of doing full chip reset. During the fastcc, tx iqcal
measurements are preserved and will be reloaded after successful
the channel change.
This patch also addressed fast channel issue where the STA can not
see APs in higher than operating channel on 5GHz band after
the association.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 5G Tx gain table w/ XPA is updated to improve spur
performance in high_power Tx gain table.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ar9003 table is updated to increase XLNA BIAS
output driver strengh.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of not clearing Bit 14 of AR_WA, the ASPM L1 is not
enabled when entering into sleep mode. AR9480 does not need
bit 14 to be set.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of warnings found by running
'make namespacecheck':
1. Remove dead code.
2. Reorder function definitions to avoid forward declarations.
3. Remove unnecessary function/structure declarations and mark
them as static.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently global wait condition (adapter->cmd_wait_q.condition)
is used while sending synchronous commands to FW. When two threads
enter in mwifiex_send_cmd_sync() routine at the same time, both the
threads wait for their command responses. Since wait condition is
same for both, they wake up simultaneously after getting response
of 1st command. After this when a thread is waiting for command
response of 3rd command, it wakes up after getting response of 2nd
command and so on. Therefore we don't wait for the response of last
command(0xaa) during unload. Hence while next time loading the driver
command time out is seen for INIT command.
This problem is resolved by having separate wait condition flag for
each command(except scan command). Since scan command is treated
differently (by maintaining scan pending q etc.), newly defined flag
(scan_wait_q_woken) is used as a scan wait condition.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 55ad5962e9.
I assumed N is newer than LP, which isn't true. This regressed LP case.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wifi.c was empty after previous cleanups, so it was removed.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved the brcmu_format_flags function and brcmu_bit_desc structure
into smac. Names were adjusted accordingly.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved the brcmu_mkiovar function into fmac, adjusting the
name accordingly.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved brcmu_chspec_malformed into the only file using it. The
function name was adjusted accordingly.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved the brcmu_parse_tlvs function and brcmu_tlv structure into
the only file using them. Names were adjusted accordingly.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved the brcmu_chipname function into the only file using it.
The function name was adjusted accordingly.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved brcmu_mw_to_qdbm and brcmu_qdbm_to_mw functions into the only
file using them. Names were adjusted accordingly.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removed brcmu_bitcount, brcmu_mhz2channel, brcmu_chspec_ctlchan.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And changed function name to something more appropriate.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For scanning several timeout parameters are configured on the device.
These parameters have been endian annotated and converted appropriately.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The parameters for roaming are sent to the device and should be little
endian. These have been annotated and converted appropriately.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver requests the device for number of ie's in assoc request
and response. This needed to be endian annotated.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pairwise master key configuration is sent to the device. The
structure has been annotated for endianess checking.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan related functions provide scan parameters to the device
which need to be in little-endian. These parameters have been
annotated and conversions were placed as needed.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The configuration function for the TCP offload engine were not
taking CPU endianess into account. Proper annotations and conversions
have been added.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable allmulti was used to provision IFF_ALLMULTI to the
device as well as IFF_PROMISC. For clarity the variable has been
renamed.
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The packet filter structures were byte copied and transferred over the
host bus to the device. As such they are little endian and have been
annotated accordingly.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ht capabilities provided upon registration with mac80211 must
be in little endian. This was fixed adding cpu_to_le16() conversion.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug function did a write operation which required a different
pointer type resulting in a sparse warning.
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- removed unneeded fn prototypes from include files.
- explicitly marked fn prototypes as extern in include files.
- reordered functions to account for removed forward declarations
in include files.
- removed unused functions: brcms_c_txflowcontrol_override,
brcms_c_txflowcontrol_prio_isset, brcms_c_txflowcontrol.
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Timer functions were called at soft-irq level, leading to the limitation
that mutexes could not be used. Lifted this limitation by migrating to
work queues.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parameter 'wl' is already stored in struct brcms_timer, so the number of
function parameters could be decreased.
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix regression introduced by commit:
commit 15b3f3b006
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date: Fri Jun 3 07:54:13 2011 -0700
iwlagn: set smps mode after assoc for 1000 device
Also remove unneeded brackets on the way.
Address:
https://bugzilla.redhat.com/show_bug.cgi?id=744155
Cc: stable@kernel.org # 3.1+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch complains that "key_index" is capped at 5 in nl80211_get_key()
but iwm->keys[] only has 4 elements. I don't know if this is really
needed, but the other ->get_key() implementations seemed to check
for overflows so I've added a check here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch incorporate the differences between the 06/20/2011 and
08/16/2011 Realtek releases of the rtl8192de driver.
The changes include:
1. Update for new chip versions
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch incorporate the differences between the 06/20/2011 and
08/16/2011 Realtek releases of the rtl8192se driver.
The changes include:
1. Fixing some typos in register usage.
2. A change in the handling of decryption status for 802.11w packets.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch incorporate the differences between the 06/20/2011 and
08/16/2011 Realtek releases of the rtlwifi driver.
The changes include:
1. Adding new chip revisions including new firmware.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch incorporate the differences between the 06/20/2011 and
08/16/2011 Realtek releases of the rtlwifi driver.
The changes include:
1. Handling of IEEE80211_HW_CONNECTION_MONITOR.
2. Fix typo to get proper response to nullfunc frames.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few were missing
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl-core.c and iwl-trans-pcie-tx.c don't need to include iwl-dev.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move iwl_enable_rfkill_int to iwl-core.h, and remove the empty
iwl-helpers.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since iwl_beacon_time_mask_[high,low] are used in iwl-core.c only,
move them to there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The constants can be moved together with
the similar ones for other devices and we
can then remove the file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The inline function in this header is only used
in a single file, so we can move it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After driver split, there were no shared functions between agn and legacy;
rename iwl-rx.c to iwl-agn-rx.c
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After driver split, no need to separate station management functions
in two files, merge it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the same calling style for all the mac80211 callback functions
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add IWL_DEBUG_MAC80211 debug for all mac80211 callback function
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once enable rts/cts for aggregation queue, do not disable until the
last aggregation queue closed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When detect wrong state on shutdown aggregation queue, show more
information for debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
