linux-hardened/drivers/net/dgrs_plx9060.h
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00

175 lines
5.3 KiB
C

/*
* PLX 9060 PCI Interface chip
*/
/*
* PCI configuration registers, same offset on local and PCI sides,
* but on PCI side, must use PCI BIOS calls to read/write.
*/
#define PCI_PLXREGS_BASE_ADDR 0x10
#define PCI_PLXREGS_IO_ADDR 0x14
#define PCI_SPACE0_BASE_ADDR 0x18
#define PCI_ROM_BASE_ADDR 0x30
# define PCI_ROM_ENABLED 0x00000001
#define PCI_INT_LINE 0x3C
/*
* Registers accessible directly from PCI and local side.
* Offset is from PCI side. Add PLX_LCL_OFFSET for local address.
*/
#define PLX_LCL_OFFSET 0x80 /* Offset of regs from local side */
/*
* Local Configuration Registers
*/
#define PLX_SPACE0_RANGE 0x00 /* Range for PCI to Lcl Addr Space 0 */
#define PLX_SPACE0_BASE_ADDR 0x04 /* Lcl Base address remap */
#define PLX_ROM_RANGE 0x10 /* Range for expansion ROM (DMA) */
#define PLX_ROM_BASE_ADDR 0x14 /* Lcl base address remap for ROM */
#define PLX_BUS_REGION 0x18 /* Bus Region Descriptors */
/*
* Shared Run Time Registers
*/
#define PLX_MBOX0 0x40
#define PLX_MBOX1 0x44
#define PLX_MBOX2 0x48
#define PLX_MBOX3 0x4C
#define PLX_MBOX4 0x50
#define PLX_MBOX5 0x54
#define PLX_MBOX6 0x58
#define PLX_MBOX7 0x5C
#define PLX_PCI2LCL_DOORBELL 0x60
#define PLX_LCL2PCI_DOORBELL 0x64
#define PLX_INT_CSR 0x68 /* Interrupt Control/Status */
# define PLX_LSERR_ENABLE 0x00000001
# define PLX_LSERR_PE 0x00000002
# define PLX_SERR 0x00000004
# undef PLX_UNUSED /* 0x00000008 */
# undef PLX_UNUSED /* 0x00000010 */
# undef PLX_UNUSED /* 0x00000020 */
# undef PLX_UNUSED /* 0x00000040 */
# undef PLX_UNUSED /* 0x00000080 */
# define PLX_PCI_IE 0x00000100
# define PLX_PCI_DOORBELL_IE 0x00000200
# define PLX_PCI_ABORT_IE 0x00000400
# define PLX_PCI_LOCAL_IE 0x00000800
# define PLX_RETRY_ABORT_ENABLE 0x00001000
# define PLX_PCI_DOORBELL_INT 0x00002000
# define PLX_PCI_ABORT_INT 0x00004000
# define PLX_PCI_LOCAL_INT 0x00008000
# define PLX_LCL_IE 0x00010000
# define PLX_LCL_DOORBELL_IE 0x00020000
# define PLX_LCL_DMA0_IE 0x00040000
# define PLX_LCL_DMA1_IE 0x00080000
# define PLX_LCL_DOORBELL_INT 0x00100000
# define PLX_LCL_DMA0_INT 0x00200000
# define PLX_LCL_DMA1_INT 0x00400000
# define PLX_LCL_BIST_INT 0x00800000
# define PLX_BM_DIRECT_ 0x01000000
# define PLX_BM_DMA0_ 0x02000000
# define PLX_BM_DMA1_ 0x04000000
# define PLX_BM_ABORT_ 0x08000000
# undef PLX_UNUSED /* 0x10000000 */
# undef PLX_UNUSED /* 0x20000000 */
# undef PLX_UNUSED /* 0x40000000 */
# undef PLX_UNUSED /* 0x80000000 */
#define PLX_MISC_CSR 0x6c /* EEPROM,PCI,User,Init Control/Status*/
# define PLX_USEROUT 0x00010000
# define PLX_USERIN 0x00020000
# define PLX_EECK 0x01000000
# define PLX_EECS 0x02000000
# define PLX_EEWD 0x04000000
# define PLX_EERD 0x08000000
/*
* DMA registers. Offset is from local side
*/
#define PLX_DMA0_MODE 0x100
# define PLX_DMA_MODE_WIDTH32 0x00000003
# define PLX_DMA_MODE_WAITSTATES(X) ((X)<<2)
# define PLX_DMA_MODE_NOREADY 0x00000000
# define PLX_DMA_MODE_READY 0x00000040
# define PLX_DMA_MODE_NOBTERM 0x00000000
# define PLX_DMA_MODE_BTERM 0x00000080
# define PLX_DMA_MODE_NOBURST 0x00000000
# define PLX_DMA_MODE_BURST 0x00000100
# define PLX_DMA_MODE_NOCHAIN 0x00000000
# define PLX_DMA_MODE_CHAIN 0x00000200
# define PLX_DMA_MODE_DONE_IE 0x00000400
# define PLX_DMA_MODE_ADDR_HOLD 0x00000800
#define PLX_DMA0_PCI_ADDR 0x104
/* non-chaining mode PCI address */
#define PLX_DMA0_LCL_ADDR 0x108
/* non-chaining mode local address */
#define PLX_DMA0_SIZE 0x10C
/* non-chaining mode length */
#define PLX_DMA0_DESCRIPTOR 0x110
# define PLX_DMA_DESC_EOC 0x00000002
# define PLX_DMA_DESC_TC_IE 0x00000004
# define PLX_DMA_DESC_TO_HOST 0x00000008
# define PLX_DMA_DESC_TO_BOARD 0x00000000
# define PLX_DMA_DESC_NEXTADDR 0xFFFFfff0
#define PLX_DMA1_MODE 0x114
#define PLX_DMA1_PCI_ADDR 0x118
#define PLX_DMA1_LCL_ADDR 0x11C
#define PLX_DMA1_SIZE 0x110
#define PLX_DMA1_DESCRIPTOR 0x124
#define PLX_DMA_CSR 0x128
# define PLX_DMA_CSR_0_ENABLE 0x00000001
# define PLX_DMA_CSR_0_START 0x00000002
# define PLX_DMA_CSR_0_ABORT 0x00000004
# define PLX_DMA_CSR_0_CLR_INTR 0x00000008
# define PLX_DMA_CSR_0_DONE 0x00000010
# define PLX_DMA_CSR_1_ENABLE 0x00000100
# define PLX_DMA_CSR_1_START 0x00000200
# define PLX_DMA_CSR_1_ABORT 0x00000400
# define PLX_DMA_CSR_1_CLR_INTR 0x00000800
# define PLX_DMA_CSR_1_DONE 0x00001000
#define PLX_DMA_ARB0 0x12C
# define PLX_DMA_ARB0_LATENCY_T 0x000000FF
# define PLX_DMA_ARB0_PAUSE_T 0x0000FF00
# define PLX_DMA_ARB0_LATENCY_EN 0x00010000
# define PLX_DMA_ARB0_PAUSE_EN 0x00020000
# define PLX_DMA_ARB0_BREQ_EN 0x00040000
# define PLX_DMA_ARB0_PRI 0x00180000
# define PLX_DMA_ARB0_PRI_ROUND 0x00000000
# define PLX_DMA_ARB0_PRI_0 0x00080000
# define PLX_DMA_ARB0_PRI_1 0x00100000
#define PLX_DMA_ARB1 0x130
/* Chan 0: FIFO DEPTH=16 */
# define PLX_DMA_ARB1_0_P2L_LW_TRIG(X) ( ((X)&15) << 0 )
# define PLX_DMA_ARB1_0_L2P_LR_TRIG(X) ( ((X)&15) << 4 )
# define PLX_DMA_ARB1_0_L2P_PW_TRIG(X) ( ((X)&15) << 8 )
# define PLX_DMA_ARB1_0_P2L_PR_TRIG(X) ( ((X)&15) << 12 )
/* Chan 1: FIFO DEPTH=8 */
# define PLX_DMA_ARB1_1_P2L_LW_TRIG(X) ( ((X)& 7) << 16 )
# define PLX_DMA_ARB1_1_L2P_LR_TRIG(X) ( ((X)& 7) << 20 )
# define PLX_DMA_ARB1_1_L2P_PW_TRIG(X) ( ((X)& 7) << 24 )
# define PLX_DMA_ARB1_1_P2L_PR_TRIG(X) ( ((X)& 7) << 28 )
typedef struct _dmachain
{
ulong pciaddr;
ulong lcladdr;
ulong len;
ulong next;
} DMACHAIN;