linux-hardened/Documentation/lzo.txt

LZO stream format as understood by Linux's LZO decompressor
===========================================================

Introduction

  This is not a specification. No specification seems to be publicly available
  for the LZO stream format. This document describes what input format the LZO
  decompressor as implemented in the Linux kernel understands. The file subject
  of this analysis is lib/lzo/lzo1x_decompress_safe.c. No analysis was made on
  the compressor nor on any other implementations though it seems likely that
  the format matches the standard one. The purpose of this document is to
  better understand what the code does in order to propose more efficient fixes
  for future bug reports.

Description

  The stream is composed of a series of instructions, operands, and data. The
  instructions consist in a few bits representing an opcode, and bits forming
  the operands for the instruction, whose size and position depend on the
  opcode and on the number of literals copied by previous instruction. The
  operands are used to indicate :

    - a distance when copying data from the dictionary (past output buffer)
    - a length (number of bytes to copy from dictionary)
    - the number of literals to copy, which is retained in variable "state"
      as a piece of information for next instructions.

  Optionally depending on the opcode and operands, extra data may follow. These
  extra data can be a complement for the operand (eg: a length or a distance
  encoded on larger values), or a literal to be copied to the output buffer.

  The first byte of the block follows a different encoding from other bytes, it
  seems to be optimized for literal use only, since there is no dictionary yet
  prior to that byte.

  Lengths are always encoded on a variable size starting with a small number
  of bits in the operand. If the number of bits isn't enough to represent the
  length, up to 255 may be added in increments by consuming more bytes with a
  rate of at most 255 per extra byte (thus the compression ratio cannot exceed
  around 255:1). The variable length encoding using #bits is always the same :

       length = byte & ((1 << #bits) - 1)
       if (!length) {
               length = ((1 << #bits) - 1)
               length += 255*(number of zero bytes)
               length += first-non-zero-byte
       }
       length += constant (generally 2 or 3)

  For references to the dictionary, distances are relative to the output
  pointer. Distances are encoded using very few bits belonging to certain
  ranges, resulting in multiple copy instructions using different encodings.
  Certain encodings involve one extra byte, others involve two extra bytes
  forming a little-endian 16-bit quantity (marked LE16 below).

  After any instruction except the large literal copy, 0, 1, 2 or 3 literals
  are copied before starting the next instruction. The number of literals that
  were copied may change the meaning and behaviour of the next instruction. In
  practice, only one instruction needs to know whether 0, less than 4, or more
  literals were copied. This is the information stored in the <state> variable
  in this implementation. This number of immediate literals to be copied is
  generally encoded in the last two bits of the instruction but may also be
  taken from the last two bits of an extra operand (eg: distance).

  End of stream is declared when a block copy of distance 0 is seen. Only one
  instruction may encode this distance (0001HLLL), it takes one LE16 operand
  for the distance, thus requiring 3 bytes.

  IMPORTANT NOTE : in the code some length checks are missing because certain
  instructions are called under the assumption that a certain number of bytes
  follow because it has already been garanteed before parsing the instructions.
  They just have to "refill" this credit if they consume extra bytes. This is
  an implementation design choice independant on the algorithm or encoding.

Byte sequences

  First byte encoding :

      0..17   : follow regular instruction encoding, see below. It is worth
                noting that codes 16 and 17 will represent a block copy from
                the dictionary which is empty, and that they will always be
                invalid at this place.

      18..21  : copy 0..3 literals
                state = (byte - 17) = 0..3  [ copy <state> literals ]
                skip byte

      22..255 : copy literal string
                length = (byte - 17) = 4..238
                state = 4 [ don't copy extra literals ]
                skip byte

  Instruction encoding :

      0 0 0 0 X X X X  (0..15)
        Depends on the number of literals copied by the last instruction.
        If last instruction did not copy any literal (state == 0), this
        encoding will be a copy of 4 or more literal, and must be interpreted
        like this :

           0 0 0 0 L L L L  (0..15)  : copy long literal string
           length = 3 + (L ?: 15 + (zero_bytes * 255) + non_zero_byte)
           state = 4  (no extra literals are copied)

        If last instruction used to copy between 1 to 3 literals (encoded in
        the instruction's opcode or distance), the instruction is a copy of a
        2-byte block from the dictionary within a 1kB distance. It is worth
        noting that this instruction provides little savings since it uses 2
        bytes to encode a copy of 2 other bytes but it encodes the number of
        following literals for free. It must be interpreted like this :

           0 0 0 0 D D S S  (0..15)  : copy 2 bytes from <= 1kB distance
           length = 2
           state = S (copy S literals after this block)
         Always followed by exactly one byte : H H H H H H H H
           distance = (H << 2) + D + 1

        If last instruction used to copy 4 or more literals (as detected by
        state == 4), the instruction becomes a copy of a 3-byte block from the
        dictionary from a 2..3kB distance, and must be interpreted like this :

           0 0 0 0 D D S S  (0..15)  : copy 3 bytes from 2..3 kB distance
           length = 3
           state = S (copy S literals after this block)
         Always followed by exactly one byte : H H H H H H H H
           distance = (H << 2) + D + 2049

      0 0 0 1 H L L L  (16..31)
           Copy of a block within 16..48kB distance (preferably less than 10B)
           length = 2 + (L ?: 7 + (zero_bytes * 255) + non_zero_byte)
        Always followed by exactly one LE16 :  D D D D D D D D : D D D D D D S S
           distance = 16384 + (H << 14) + D
           state = S (copy S literals after this block)
           End of stream is reached if distance == 16384

      0 0 1 L L L L L  (32..63)
           Copy of small block within 16kB distance (preferably less than 34B)
           length = 2 + (L ?: 31 + (zero_bytes * 255) + non_zero_byte)
        Always followed by exactly one LE16 :  D D D D D D D D : D D D D D D S S
           distance = D + 1
           state = S (copy S literals after this block)

      0 1 L D D D S S  (64..127)
           Copy 3-4 bytes from block within 2kB distance
           state = S (copy S literals after this block)
           length = 3 + L
         Always followed by exactly one byte : H H H H H H H H
           distance = (H << 3) + D + 1

      1 L L D D D S S  (128..255)
           Copy 5-8 bytes from block within 2kB distance
           state = S (copy S literals after this block)
           length = 5 + L
         Always followed by exactly one byte : H H H H H H H H
           distance = (H << 3) + D + 1

Authors

  This document was written by Willy Tarreau <w@1wt.eu> on 2014/07/19 during an
  analysis of the decompression code available in Linux 3.16-rc5. The code is
  tricky, it is possible that this document contains mistakes or that a few
  corner cases were overlooked. In any case, please report any doubt, fix, or
  proposed updates to the author(s) so that the document can be updated.