3470cb1d4f
The rest of 8390 conversions; ifdef cascade in 8390.h is gone now. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
192 lines
8.1 KiB
C
192 lines
8.1 KiB
C
/* Generic NS8390 register definitions. */
|
|
/* This file is part of Donald Becker's 8390 drivers, and is distributed
|
|
under the same license. Auto-loading of 8390.o only in v2.2 - Paul G.
|
|
Some of these names and comments originated from the Crynwr
|
|
packet drivers, which are distributed under the GPL. */
|
|
|
|
#ifndef _8390_h
|
|
#define _8390_h
|
|
|
|
#include <linux/if_ether.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/skbuff.h>
|
|
|
|
#define TX_PAGES 12 /* Two Tx slots */
|
|
|
|
#define ETHER_ADDR_LEN 6
|
|
|
|
/* The 8390 specific per-packet-header format. */
|
|
struct e8390_pkt_hdr {
|
|
unsigned char status; /* status */
|
|
unsigned char next; /* pointer to next packet. */
|
|
unsigned short count; /* header + packet length in bytes */
|
|
};
|
|
|
|
#ifdef notdef
|
|
extern int ei_debug;
|
|
#else
|
|
#define ei_debug 1
|
|
#endif
|
|
|
|
#ifdef CONFIG_NET_POLL_CONTROLLER
|
|
extern void ei_poll(struct net_device *dev);
|
|
#endif
|
|
|
|
extern void NS8390_init(struct net_device *dev, int startp);
|
|
extern int ei_open(struct net_device *dev);
|
|
extern int ei_close(struct net_device *dev);
|
|
extern irqreturn_t ei_interrupt(int irq, void *dev_id);
|
|
extern struct net_device *__alloc_ei_netdev(int size);
|
|
static inline struct net_device *alloc_ei_netdev(void)
|
|
{
|
|
return __alloc_ei_netdev(0);
|
|
}
|
|
|
|
/* You have one of these per-board */
|
|
struct ei_device {
|
|
const char *name;
|
|
void (*reset_8390)(struct net_device *);
|
|
void (*get_8390_hdr)(struct net_device *, struct e8390_pkt_hdr *, int);
|
|
void (*block_output)(struct net_device *, int, const unsigned char *, int);
|
|
void (*block_input)(struct net_device *, int, struct sk_buff *, int);
|
|
unsigned long rmem_start;
|
|
unsigned long rmem_end;
|
|
void __iomem *mem;
|
|
unsigned char mcfilter[8];
|
|
unsigned open:1;
|
|
unsigned word16:1; /* We have the 16-bit (vs 8-bit) version of the card. */
|
|
unsigned bigendian:1; /* 16-bit big endian mode. Do NOT */
|
|
/* set this on random 8390 clones! */
|
|
unsigned txing:1; /* Transmit Active */
|
|
unsigned irqlock:1; /* 8390's intrs disabled when '1'. */
|
|
unsigned dmaing:1; /* Remote DMA Active */
|
|
unsigned char tx_start_page, rx_start_page, stop_page;
|
|
unsigned char current_page; /* Read pointer in buffer */
|
|
unsigned char interface_num; /* Net port (AUI, 10bT.) to use. */
|
|
unsigned char txqueue; /* Tx Packet buffer queue length. */
|
|
short tx1, tx2; /* Packet lengths for ping-pong tx. */
|
|
short lasttx; /* Alpha version consistency check. */
|
|
unsigned char reg0; /* Register '0' in a WD8013 */
|
|
unsigned char reg5; /* Register '5' in a WD8013 */
|
|
unsigned char saved_irq; /* Original dev->irq value. */
|
|
struct net_device_stats stat; /* The new statistics table. */
|
|
u32 *reg_offset; /* Register mapping table */
|
|
spinlock_t page_lock; /* Page register locks */
|
|
unsigned long priv; /* Private field to store bus IDs etc. */
|
|
};
|
|
|
|
/* The maximum number of 8390 interrupt service routines called per IRQ. */
|
|
#define MAX_SERVICE 12
|
|
|
|
/* The maximum time waited (in jiffies) before assuming a Tx failed. (20ms) */
|
|
#define TX_TIMEOUT (20*HZ/100)
|
|
|
|
#define ei_status (*(struct ei_device *)netdev_priv(dev))
|
|
|
|
/* Some generic ethernet register configurations. */
|
|
#define E8390_TX_IRQ_MASK 0xa /* For register EN0_ISR */
|
|
#define E8390_RX_IRQ_MASK 0x5
|
|
#define E8390_RXCONFIG 0x4 /* EN0_RXCR: broadcasts, no multicast,errors */
|
|
#define E8390_RXOFF 0x20 /* EN0_RXCR: Accept no packets */
|
|
#define E8390_TXCONFIG 0x00 /* EN0_TXCR: Normal transmit mode */
|
|
#define E8390_TXOFF 0x02 /* EN0_TXCR: Transmitter off */
|
|
|
|
/* Register accessed at EN_CMD, the 8390 base addr. */
|
|
#define E8390_STOP 0x01 /* Stop and reset the chip */
|
|
#define E8390_START 0x02 /* Start the chip, clear reset */
|
|
#define E8390_TRANS 0x04 /* Transmit a frame */
|
|
#define E8390_RREAD 0x08 /* Remote read */
|
|
#define E8390_RWRITE 0x10 /* Remote write */
|
|
#define E8390_NODMA 0x20 /* Remote DMA */
|
|
#define E8390_PAGE0 0x00 /* Select page chip registers */
|
|
#define E8390_PAGE1 0x40 /* using the two high-order bits */
|
|
#define E8390_PAGE2 0x80 /* Page 3 is invalid. */
|
|
|
|
/*
|
|
* Only generate indirect loads given a machine that needs them.
|
|
* - removed AMIGA_PCMCIA from this list, handled as ISA io now
|
|
*/
|
|
|
|
#ifndef ei_inb
|
|
#define ei_inb(_p) inb(_p)
|
|
#define ei_outb(_v,_p) outb(_v,_p)
|
|
#define ei_inb_p(_p) inb_p(_p)
|
|
#define ei_outb_p(_v,_p) outb_p(_v,_p)
|
|
#endif
|
|
|
|
#ifndef EI_SHIFT
|
|
#define EI_SHIFT(x) (x)
|
|
#endif
|
|
|
|
#define E8390_CMD EI_SHIFT(0x00) /* The command register (for all pages) */
|
|
/* Page 0 register offsets. */
|
|
#define EN0_CLDALO EI_SHIFT(0x01) /* Low byte of current local dma addr RD */
|
|
#define EN0_STARTPG EI_SHIFT(0x01) /* Starting page of ring bfr WR */
|
|
#define EN0_CLDAHI EI_SHIFT(0x02) /* High byte of current local dma addr RD */
|
|
#define EN0_STOPPG EI_SHIFT(0x02) /* Ending page +1 of ring bfr WR */
|
|
#define EN0_BOUNDARY EI_SHIFT(0x03) /* Boundary page of ring bfr RD WR */
|
|
#define EN0_TSR EI_SHIFT(0x04) /* Transmit status reg RD */
|
|
#define EN0_TPSR EI_SHIFT(0x04) /* Transmit starting page WR */
|
|
#define EN0_NCR EI_SHIFT(0x05) /* Number of collision reg RD */
|
|
#define EN0_TCNTLO EI_SHIFT(0x05) /* Low byte of tx byte count WR */
|
|
#define EN0_FIFO EI_SHIFT(0x06) /* FIFO RD */
|
|
#define EN0_TCNTHI EI_SHIFT(0x06) /* High byte of tx byte count WR */
|
|
#define EN0_ISR EI_SHIFT(0x07) /* Interrupt status reg RD WR */
|
|
#define EN0_CRDALO EI_SHIFT(0x08) /* low byte of current remote dma address RD */
|
|
#define EN0_RSARLO EI_SHIFT(0x08) /* Remote start address reg 0 */
|
|
#define EN0_CRDAHI EI_SHIFT(0x09) /* high byte, current remote dma address RD */
|
|
#define EN0_RSARHI EI_SHIFT(0x09) /* Remote start address reg 1 */
|
|
#define EN0_RCNTLO EI_SHIFT(0x0a) /* Remote byte count reg WR */
|
|
#define EN0_RCNTHI EI_SHIFT(0x0b) /* Remote byte count reg WR */
|
|
#define EN0_RSR EI_SHIFT(0x0c) /* rx status reg RD */
|
|
#define EN0_RXCR EI_SHIFT(0x0c) /* RX configuration reg WR */
|
|
#define EN0_TXCR EI_SHIFT(0x0d) /* TX configuration reg WR */
|
|
#define EN0_COUNTER0 EI_SHIFT(0x0d) /* Rcv alignment error counter RD */
|
|
#define EN0_DCFG EI_SHIFT(0x0e) /* Data configuration reg WR */
|
|
#define EN0_COUNTER1 EI_SHIFT(0x0e) /* Rcv CRC error counter RD */
|
|
#define EN0_IMR EI_SHIFT(0x0f) /* Interrupt mask reg WR */
|
|
#define EN0_COUNTER2 EI_SHIFT(0x0f) /* Rcv missed frame error counter RD */
|
|
|
|
/* Bits in EN0_ISR - Interrupt status register */
|
|
#define ENISR_RX 0x01 /* Receiver, no error */
|
|
#define ENISR_TX 0x02 /* Transmitter, no error */
|
|
#define ENISR_RX_ERR 0x04 /* Receiver, with error */
|
|
#define ENISR_TX_ERR 0x08 /* Transmitter, with error */
|
|
#define ENISR_OVER 0x10 /* Receiver overwrote the ring */
|
|
#define ENISR_COUNTERS 0x20 /* Counters need emptying */
|
|
#define ENISR_RDC 0x40 /* remote dma complete */
|
|
#define ENISR_RESET 0x80 /* Reset completed */
|
|
#define ENISR_ALL 0x3f /* Interrupts we will enable */
|
|
|
|
/* Bits in EN0_DCFG - Data config register */
|
|
#define ENDCFG_WTS 0x01 /* word transfer mode selection */
|
|
#define ENDCFG_BOS 0x02 /* byte order selection */
|
|
|
|
/* Page 1 register offsets. */
|
|
#define EN1_PHYS EI_SHIFT(0x01) /* This board's physical enet addr RD WR */
|
|
#define EN1_PHYS_SHIFT(i) EI_SHIFT(i+1) /* Get and set mac address */
|
|
#define EN1_CURPAG EI_SHIFT(0x07) /* Current memory page RD WR */
|
|
#define EN1_MULT EI_SHIFT(0x08) /* Multicast filter mask array (8 bytes) RD WR */
|
|
#define EN1_MULT_SHIFT(i) EI_SHIFT(8+i) /* Get and set multicast filter */
|
|
|
|
/* Bits in received packet status byte and EN0_RSR*/
|
|
#define ENRSR_RXOK 0x01 /* Received a good packet */
|
|
#define ENRSR_CRC 0x02 /* CRC error */
|
|
#define ENRSR_FAE 0x04 /* frame alignment error */
|
|
#define ENRSR_FO 0x08 /* FIFO overrun */
|
|
#define ENRSR_MPA 0x10 /* missed pkt */
|
|
#define ENRSR_PHY 0x20 /* physical/multicast address */
|
|
#define ENRSR_DIS 0x40 /* receiver disable. set in monitor mode */
|
|
#define ENRSR_DEF 0x80 /* deferring */
|
|
|
|
/* Transmitted packet status, EN0_TSR. */
|
|
#define ENTSR_PTX 0x01 /* Packet transmitted without error */
|
|
#define ENTSR_ND 0x02 /* The transmit wasn't deferred. */
|
|
#define ENTSR_COL 0x04 /* The transmit collided at least once. */
|
|
#define ENTSR_ABT 0x08 /* The transmit collided 16 times, and was deferred. */
|
|
#define ENTSR_CRS 0x10 /* The carrier sense was lost. */
|
|
#define ENTSR_FU 0x20 /* A "FIFO underrun" occurred during transmit. */
|
|
#define ENTSR_CDH 0x40 /* The collision detect "heartbeat" signal was lost. */
|
|
#define ENTSR_OWC 0x80 /* There was an out-of-window collision. */
|
|
|
|
#endif /* _8390_h */
|