ce5a111a1b
Documentation/i2c/fault-codes illustrates EINVAL error code as follows: "One example would be a driver trying an SMBus Block Write with block size outside the range of 1-32 bytes." However, the actual implementation of i2c subsystem truncates data length to be 32 bytes. Hence this example cannot happen anymore, and since it's obsolete, let's simply remove it from Documentation/i2c/fault-codes. Signed-off-by: Helia Correia <helia.correia@intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
124 lines
4.9 KiB
Text
124 lines
4.9 KiB
Text
This is a summary of the most important conventions for use of fault
|
|
codes in the I2C/SMBus stack.
|
|
|
|
|
|
A "Fault" is not always an "Error"
|
|
----------------------------------
|
|
Not all fault reports imply errors; "page faults" should be a familiar
|
|
example. Software often retries idempotent operations after transient
|
|
faults. There may be fancier recovery schemes that are appropriate in
|
|
some cases, such as re-initializing (and maybe resetting). After such
|
|
recovery, triggered by a fault report, there is no error.
|
|
|
|
In a similar way, sometimes a "fault" code just reports one defined
|
|
result for an operation ... it doesn't indicate that anything is wrong
|
|
at all, just that the outcome wasn't on the "golden path".
|
|
|
|
In short, your I2C driver code may need to know these codes in order
|
|
to respond correctly. Other code may need to rely on YOUR code reporting
|
|
the right fault code, so that it can (in turn) behave correctly.
|
|
|
|
|
|
I2C and SMBus fault codes
|
|
-------------------------
|
|
These are returned as negative numbers from most calls, with zero or
|
|
some positive number indicating a non-fault return. The specific
|
|
numbers associated with these symbols differ between architectures,
|
|
though most Linux systems use <asm-generic/errno*.h> numbering.
|
|
|
|
Note that the descriptions here are not exhaustive. There are other
|
|
codes that may be returned, and other cases where these codes should
|
|
be returned. However, drivers should not return other codes for these
|
|
cases (unless the hardware doesn't provide unique fault reports).
|
|
|
|
Also, codes returned by adapter probe methods follow rules which are
|
|
specific to their host bus (such as PCI, or the platform bus).
|
|
|
|
|
|
EAGAIN
|
|
Returned by I2C adapters when they lose arbitration in master
|
|
transmit mode: some other master was transmitting different
|
|
data at the same time.
|
|
|
|
Also returned when trying to invoke an I2C operation in an
|
|
atomic context, when some task is already using that I2C bus
|
|
to execute some other operation.
|
|
|
|
EBADMSG
|
|
Returned by SMBus logic when an invalid Packet Error Code byte
|
|
is received. This code is a CRC covering all bytes in the
|
|
transaction, and is sent before the terminating STOP. This
|
|
fault is only reported on read transactions; the SMBus slave
|
|
may have a way to report PEC mismatches on writes from the
|
|
host. Note that even if PECs are in use, you should not rely
|
|
on these as the only way to detect incorrect data transfers.
|
|
|
|
EBUSY
|
|
Returned by SMBus adapters when the bus was busy for longer
|
|
than allowed. This usually indicates some device (maybe the
|
|
SMBus adapter) needs some fault recovery (such as resetting),
|
|
or that the reset was attempted but failed.
|
|
|
|
EINVAL
|
|
This rather vague error means an invalid parameter has been
|
|
detected before any I/O operation was started. Use a more
|
|
specific fault code when you can.
|
|
|
|
EIO
|
|
This rather vague error means something went wrong when
|
|
performing an I/O operation. Use a more specific fault
|
|
code when you can.
|
|
|
|
ENODEV
|
|
Returned by driver probe() methods. This is a bit more
|
|
specific than ENXIO, implying the problem isn't with the
|
|
address, but with the device found there. Driver probes
|
|
may verify the device returns *correct* responses, and
|
|
return this as appropriate. (The driver core will warn
|
|
about probe faults other than ENXIO and ENODEV.)
|
|
|
|
ENOMEM
|
|
Returned by any component that can't allocate memory when
|
|
it needs to do so.
|
|
|
|
ENXIO
|
|
Returned by I2C adapters to indicate that the address phase
|
|
of a transfer didn't get an ACK. While it might just mean
|
|
an I2C device was temporarily not responding, usually it
|
|
means there's nothing listening at that address.
|
|
|
|
Returned by driver probe() methods to indicate that they
|
|
found no device to bind to. (ENODEV may also be used.)
|
|
|
|
EOPNOTSUPP
|
|
Returned by an adapter when asked to perform an operation
|
|
that it doesn't, or can't, support.
|
|
|
|
For example, this would be returned when an adapter that
|
|
doesn't support SMBus block transfers is asked to execute
|
|
one. In that case, the driver making that request should
|
|
have verified that functionality was supported before it
|
|
made that block transfer request.
|
|
|
|
Similarly, if an I2C adapter can't execute all legal I2C
|
|
messages, it should return this when asked to perform a
|
|
transaction it can't. (These limitations can't be seen in
|
|
the adapter's functionality mask, since the assumption is
|
|
that if an adapter supports I2C it supports all of I2C.)
|
|
|
|
EPROTO
|
|
Returned when slave does not conform to the relevant I2C
|
|
or SMBus (or chip-specific) protocol specifications. One
|
|
case is when the length of an SMBus block data response
|
|
(from the SMBus slave) is outside the range 1-32 bytes.
|
|
|
|
ETIMEDOUT
|
|
This is returned by drivers when an operation took too much
|
|
time, and was aborted before it completed.
|
|
|
|
SMBus adapters may return it when an operation took more
|
|
time than allowed by the SMBus specification; for example,
|
|
when a slave stretches clocks too far. I2C has no such
|
|
timeouts, but it's normal for I2C adapters to impose some
|
|
arbitrary limits (much longer than SMBus!) too.
|
|
|