pkglint --only "https instead of http" -r -F
With manual adjustments afterwards since pkglint 19.4.4 fixed a few
indentations in unrelated lines.
This mainly affects projects hosted at SourceForce, as well as
freedesktop.org, CTAN and GNU.
- drop patch, seems included in upstream with condition:
#if !GLIB_CHECK_VERSION(2,32,0)
(upstream)
- Updated ham/grig to 0.8.1
-------------------------
GRIG 0.8.1:
- Maintenance update
- French l10n
Existing SHA1 digests verified, all found to be the same on the
machine holding the existing distfiles (morden). Existing SHA1
digests retained for now as an audit trail.
to address issues with NetBSD-6(and earlier)'s fontconfig not being
new enough for pango.
While doing that, also bump freetype2 dependency to current pkgsrc
version.
Suggested by tron in PR 47882
GRIG 0.8.0:
- Frequency entry via keypad (thanks to Alessandro Zummo).
- Arrow LEFT/RIGHT will change the frequency with the smallest step. This can
be used for tuning using external devices like the Powermate.
* Support for VFO->MEM and MEM->VFO function.
- Support on/off rig functions.
- Added an extra gigahertz digit in lcd display
- Added antenna control
- French l10n
- Fixed crash that occurs when mouse is clicked between MHz and kHz digits.
Reported as Ubuntu bug 517816.
- Requires Gtk+ 2.12 and Hamlib 1.2.8
GRIG 0.7.2:
- Fixed bug that caused wrong handling of RF gain, IF shift, MIC gain,
and compressor controls (bug #1613622).
- Give volume level control higher priority to avoid jumpy behaviour
(bug #1616926).
GRIG 0.7.1:
- A bug that caused installation to fail has been fixed (#1523367).
GRIG 0.7.0:
- Added receiver and transmitter level controls.
- Fixed bug that caused installation errors when using autoconf 2.59e.
- Pixmaps are now installed to /usr/local/share/pixmaps/grig instead of
/usr/local/share/grig/pixmaps by default (related to the above bug).
GRIG 0.6.0:
- Save and restore RIG state.
- RF power meter scale is now functional with ranges of 5, 10, 50, 100
and 500 watts. There is currently a bug, which causes the meter needle
to jump up when switching between RX/TX.
- Fixed bug, which caused the frequency reading to flicker between the
current value and a previously set value (bug #1388342). Same bug was
found for the PTT and POWER controls, too.
- Fixed bug, which gave the error message "Can not find VFO list for this
rig! Bug in backend?" if the rig did not have any of the rig_set_vfo or
rig_get_vfo functions (bug #1440876).
- Better error messages when a command fails to execute.
- Fixed bug, which blocked the debug handler to properly filter messages
coming from grig (hamlib messages were filtered correctly).
GRIG 0.5.0:
- Requires Gtk+ 2.6 and Hamlib 1.2.5
- Added VFO and SPLIT controls.
- Special rig functions: LOCK, ...
- Use own debug handler for both hamlib and grig messages
and format debug messages so that become easier to analyse.
- New debug message window, which can be used to analyse
previously saved debug messages.
- Modified shutdown procedure to wait until daemon actually
finishes instead of using a fixed length timeout.
- Disable POWER and PTT buttons by default (can be enabled
via the command line).
- Optimisation of the daemon process allowing faster reaction
when PTT is toggled.
- The mode selector combo only shows modes, which are supported
by the rig.
- Fixed erroneous detection of set/get level availability
(bug #1266068).
- Fixed incorrect handling of empty ATT, PREAMP and tuning
step lists in the Radio Info window (bug #1266071).
- Fixed a bug, which caused grig to display WIDE instead of
NORMAL passband when the rig has no wide passband.
- Optimised S-meter dynamics.
- Better detection of frequency ranges and resolutions.
- Corrected various mistakes in the manual page.
- Various minor improvements to the user interface.
- Several minor changes to support wintendo builds.
