to address issues with NetBSD-6(and earlier)'s fontconfig not being
new enough for pango.
While doing that, also bump freetype2 dependency to current pkgsrc
version.
Suggested by tron in PR 47882
GRIG 0.8.0:
- Frequency entry via keypad (thanks to Alessandro Zummo).
- Arrow LEFT/RIGHT will change the frequency with the smallest step. This can
be used for tuning using external devices like the Powermate.
* Support for VFO->MEM and MEM->VFO function.
- Support on/off rig functions.
- Added an extra gigahertz digit in lcd display
- Added antenna control
- French l10n
- Fixed crash that occurs when mouse is clicked between MHz and kHz digits.
Reported as Ubuntu bug 517816.
- Requires Gtk+ 2.12 and Hamlib 1.2.8
GRIG 0.7.2:
- Fixed bug that caused wrong handling of RF gain, IF shift, MIC gain,
and compressor controls (bug #1613622).
- Give volume level control higher priority to avoid jumpy behaviour
(bug #1616926).
GRIG 0.7.1:
- A bug that caused installation to fail has been fixed (#1523367).
GRIG 0.7.0:
- Added receiver and transmitter level controls.
- Fixed bug that caused installation errors when using autoconf 2.59e.
- Pixmaps are now installed to /usr/local/share/pixmaps/grig instead of
/usr/local/share/grig/pixmaps by default (related to the above bug).
GRIG 0.6.0:
- Save and restore RIG state.
- RF power meter scale is now functional with ranges of 5, 10, 50, 100
and 500 watts. There is currently a bug, which causes the meter needle
to jump up when switching between RX/TX.
- Fixed bug, which caused the frequency reading to flicker between the
current value and a previously set value (bug #1388342). Same bug was
found for the PTT and POWER controls, too.
- Fixed bug, which gave the error message "Can not find VFO list for this
rig! Bug in backend?" if the rig did not have any of the rig_set_vfo or
rig_get_vfo functions (bug #1440876).
- Better error messages when a command fails to execute.
- Fixed bug, which blocked the debug handler to properly filter messages
coming from grig (hamlib messages were filtered correctly).
GRIG 0.5.0:
- Requires Gtk+ 2.6 and Hamlib 1.2.5
- Added VFO and SPLIT controls.
- Special rig functions: LOCK, ...
- Use own debug handler for both hamlib and grig messages
and format debug messages so that become easier to analyse.
- New debug message window, which can be used to analyse
previously saved debug messages.
- Modified shutdown procedure to wait until daemon actually
finishes instead of using a fixed length timeout.
- Disable POWER and PTT buttons by default (can be enabled
via the command line).
- Optimisation of the daemon process allowing faster reaction
when PTT is toggled.
- The mode selector combo only shows modes, which are supported
by the rig.
- Fixed erroneous detection of set/get level availability
(bug #1266068).
- Fixed incorrect handling of empty ATT, PREAMP and tuning
step lists in the Radio Info window (bug #1266071).
- Fixed a bug, which caused grig to display WIDE instead of
NORMAL passband when the rig has no wide passband.
- Optimised S-meter dynamics.
- Better detection of frequency ranges and resolutions.
- Corrected various mistakes in the manual page.
- Various minor improvements to the user interface.
- Several minor changes to support wintendo builds.
added features and bug fixes including -
* removal of rotator and GConf related code
* debug level menu
* additional command line options
* read meter value for TX PWR, SWR and ALC
in the process. (More information on tech-pkg.)
Bump PKGREVISION and BUILDLINK_DEPENDS of all packages using libtool and
installing .la files.
Bump PKGREVISION (only) of all packages depending directly on the above
via a buildlink3 include.
