This patch introduces two things: First this_cpu_ptr and then per cpu
atomic operations.
this_cpu_ptr
------------
A common operation when dealing with cpu data is to get the instance of the
cpu data associated with the currently executing processor. This can be
optimized by
this_cpu_ptr(xx) = per_cpu_ptr(xx, smp_processor_id).
The problem with per_cpu_ptr(x, smp_processor_id) is that it requires
an array lookup to find the offset for the cpu. Processors typically
have the offset for the current cpu area in some kind of (arch dependent)
efficiently accessible register or memory location.
We can use that instead of doing the array lookup to speed up the
determination of the address of the percpu variable. This is particularly
significant because these lookups occur in performance critical paths
of the core kernel. this_cpu_ptr() can avoid memory accesses and
this_cpu_ptr comes in two flavors. The preemption context matters since we
are referring the the currently executing processor. In many cases we must
insure that the processor does not change while a code segment is executed.
__this_cpu_ptr -> Do not check for preemption context
this_cpu_ptr -> Check preemption context
The parameter to these operations is a per cpu pointer. This can be the
address of a statically defined per cpu variable (&per_cpu_var(xxx)) or
the address of a per cpu variable allocated with the per cpu allocator.
per cpu atomic operations: this_cpu_*(var, val)
-----------------------------------------------
this_cpu_* operations (like this_cpu_add(struct->y, value) operate on
abitrary scalars that are members of structures allocated with the new
per cpu allocator. They can also operate on static per_cpu variables
if they are passed to per_cpu_var() (See patch to use this_cpu_*
operations for vm statistics).
These operations are guaranteed to be atomic vs preemption when modifying
the scalar. The calculation of the per cpu offset is also guaranteed to
be atomic at the same time. This means that a this_cpu_* operation can be
safely used to modify a per cpu variable in a context where interrupts are
enabled and preemption is allowed. Many architectures can perform such
a per cpu atomic operation with a single instruction.
Note that the atomicity here is different from regular atomic operations.
Atomicity is only guaranteed for data accessed from the currently executing
processor. Modifications from other processors are still possible. There
must be other guarantees that the per cpu data is not modified from another
processor when using these instruction. The per cpu atomicity is created
by the fact that the processor either executes and instruction or not.
Embedded in the instruction is the relocation of the per cpu address to
the are reserved for the current processor and the RMW action. Therefore
interrupts or preemption cannot occur in the mids of this processing.
Generic fallback functions are used if an arch does not define optimized
this_cpu operations. The functions come also come in the two flavors used
for this_cpu_ptr().
The firstparameter is a scalar that is a member of a structure allocated
through allocpercpu or a per cpu variable (use per_cpu_var(xxx)). The
operations are similar to what percpu_add() and friends do.
this_cpu_read(scalar)
this_cpu_write(scalar, value)
this_cpu_add(scale, value)
this_cpu_sub(scalar, value)
this_cpu_inc(scalar)
this_cpu_dec(scalar)
this_cpu_and(scalar, value)
this_cpu_or(scalar, value)
this_cpu_xor(scalar, value)
Arch code can override the generic functions and provide optimized atomic
per cpu operations. These atomic operations must provide both the relocation
(x86 does it through a segment override) and the operation on the data in a
single instruction. Otherwise preempt needs to be disabled and there is no
gain from providing arch implementations.
A third variant is provided prefixed by irqsafe_. These variants are safe
against hardware interrupts on the *same* processor (all per cpu atomic
primitives are *always* *only* providing safety for code running on the
*same* processor!). The increment needs to be implemented by the hardware
in such a way that it is a single RMW instruction that is either processed
before or after an interrupt.
cc: David Howells <dhowells@redhat.com>
cc: Ingo Molnar <mingo@elte.hu>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
With ia64 converted, there's no arch left which still uses legacy
percpu allocator. Kill it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Delightedly-acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Unlike other archs, ia64 reserves space for percpu areas during early
memory initialization. These areas occupy a contiguous region indexed
by cpu number on contiguous memory model or are grouped by node on
discontiguous memory model.
As allocation and initialization are done by the arch code, all that
setup_per_cpu_areas() needs to do is communicating the determined
layout to the percpu allocator. This patch implements
setup_per_cpu_areas() for both contig and discontig memory models and
drops HAVE_LEGACY_PER_CPU_AREA.
Please note that for contig model, the allocation itself is modified
only to allocate for possible cpus instead of NR_CPUS. As dynamic
percpu allocator can handle non-direct mapping, there's no reason to
allocate memory for cpus which aren't possible.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64 <linux-ia64@vger.kernel.org>
cpu0 used special percpu area reserved by the linker, __cpu0_per_cpu,
which is set up early in boot by head.S. However, this doesn't
guarantee that the area will be on the same node as cpu0 and the
percpu area for cpu0 ends up very far away from percpu areas for other
cpus which cause problems for congruent percpu allocator.
This patch makes percpu area initialization allocate percpu area for
cpu0 like any other cpus and copy it from __cpu0_per_cpu which now
resides in the __init area. This means that for cpu0, percpu area is
first setup at __cpu0_per_cpu early by head.S and then moved to an
area in the linear mapping during memory initialization and it's not
allowed to take a pointer to percpu variables between head.S and
memory initialization.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64 <linux-ia64@vger.kernel.org>
All information necessary to initialize cpu possible and present maps
are available once early_acpi_boot_init() is complete. Reorganize
setup_arch() and acpi init functions such that,
* CPU information is printed after LAPIC entries are parsed in
early_acpi_boot_init().
* smp_build_cpu_map() is called by setup_arch() instead of acpi
functions.
* smp_build_cpu_map() is called once all CPU related information is
available before memory is initialized.
This is primarily to allow find_memory() to use cpu maps but is also a
general cleanup. Please note that with this change, the somewhat
ad-hoc early_cpu_possible_map defined and used for NUMA configurations
is probably unnecessary. Something to clean up another day.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64 <linux-ia64@vger.kernel.org>
If CONFIG_VIRTUAL_MEM_MAP is enabled, ia64 defines macro VMALLOC_END
as unsigned long variable vmalloc_end which is adjusted to prepare
room for vmemmap. This becomes probnlematic if a local variables
vmalloc_end is defined in some function (not very unlikely) and
VMALLOC_END is used in the function - the function thinks its
referencing the global VMALLOC_END value but would be referencing its
own local vmalloc_end variable.
There's no reason VMALLOC_END should be a macro. Just define it as an
unsigned long variable if CONFIG_VIRTUAL_MEM_MAP is set to avoid nasty
surprises.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64 <linux-ia64@vger.kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix data space leak fix
Btrfs: remove duplicates of filemap_ helpers
Btrfs: take i_mutex before generic_write_checks
Btrfs: fix arguments to btrfs_wait_on_page_writeback_range
Btrfs: fix deadlock with free space handling and user transactions
Btrfs: fix error cases for ioctl transactions
Btrfs: Use CONFIG_BTRFS_POSIX_ACL to enable ACL code
Btrfs: introduce missing kfree
Btrfs: Fix setting umask when POSIX ACLs are not enabled
Btrfs: proper -ENOSPC handling
spi_imx_chipselect() made things that should be (and mostly are) done by
spi_imx_setupxfer. Only setting the tx and rx functions was missing.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise the config function uses random data from the stack. This
didn't stick out because config is called once more in the chipselect
function with correct parameters.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spi_imx_setup() is only called by spi_setup(). The latter does the
initialization already.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can only setup the gpio pins in spi_setup time when we know the
SPI_CS_HIGH setting.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the filename match the Kconfig symbol and the driver name.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's just a wrapper for <linux/fscache.h>, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using %*s, sscanf should honor conversion specifiers immediately
following the %*s. For example, the following code should find the
position of the end of the string "hello".
int end;
char buf[] = "hello world";
sscanf(buf, "%*s%n", &end);
printf("%d\n", end);
Ideally, sscanf would advance the fmt and str pointers the same as it
would without the *, but the code for that is rather complicated and is
not included in the patch.
Signed-off-by: Andy Spencer <andy753421@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow users to force skipping the TXEN test at init time. Applies
to all serial ports. Intended for debugging only.
There is a blacklist for devices where we need to skip the test but the
list is not complete. This lets users force skipping the test so we can
determine if they need to be added to the list.
Some HP machines with weird serial consoles have this problem and there
may be more.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check whether index is within bounds before grabbing the element.
Also, since NR_PORTS is defined ARRAY_SIZE(cy_port), cy_port[NR_PORTS] is
out of bounds as well.
[akpm@linux-foundation.org: cleanup, remove (long) casts]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
irq is declared with size NR_CARDS (4), but the loop containing this
segment runs up until NR_ISA_ADDRS (16), possibly reading from irq[i] (and
trying to use the result)
Identified by the Parfait static scanner.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add better support for omitting either the card detect or the write
protect GPIOs if the board does not support it. Add the fields
no_wprotect and no_detect to the platform data which when set indicate the
absence of the respective GPIOs.
Note, this also fixes a minor bug where it tries to free IRQ0 if there is
no detect gpio available.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have found a couple of boards where the SDIO IRQ hardware support has
failed to work properly, and thus we should make it configurable whether
or not to be included in the driver.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes for the DMA transfer mode of the driver to try and improve the state
of the code:
- Ensure that dma_complete is set during the end of the command phase
so that transfers do not stall awaiting the completion
- Update the DMA debugging to provide a bit more useful information
such as how many DMA descriptors where not processed and print the
DMA addresses in hexadecimal.
- Fix the DMA channel request code to actually request DMA for the
S3CMCI block instead of whatever '0' signified.
- Add fallback to PIO if we cannot get the DMA channel, as many of the
devices with this block only have a limited number of DMA channels.
- Only try and claim and free the DMA channel if we are trying to use it.
This improves the driver DMA code to the point where it can now identify a
card and read the partition table. However the DMA can still stall when
trying to move data between the host and memory.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a selection for the data transfer mode of the s3cmci driver, allowing
for either a configuration or rumtime selection of the use of the DMA or
PIO transfer code.
The PIO only mode is 476 bytes smaller than the driver with both methods
compiled in.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The controller supports SDIO IRQ detection so add support for hardware
assisted SDIO interrupt detection for the SDIO core. This improves the
response time for SDIO interrupts and thus the transfer rate from devices
such as the Marvel 8686.
As a note, it does seem that the controller will miss an IRQ than is held
asserted, so there are some manual checks to see if the SDIO interrupt is
active after a transfer.
Major testing on the S3C2440.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export driver state and hardware register state via debugfs entries
created under a directory formed from dev_name() on the probed device when
CONFIG_DEBUG_FS is set.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clear_imask() call should be used to clear the interrupt mask
register, as it may end up clearing the SDIO interrupt bit if this is
enabled.
Change all writes of zero to SDIIMSK register to use clear_imask() ready
for the SDIO updates.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move to using dev_pm_ops for suspend and resume.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move to using gpiolib to access the card detect and write protect GPIO
lines instead of using the platform speicifc s3c2410_gpio calls.
Also ensure that the card lines are claimed the same way to avoid overlap
with any other drivers.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the platform id list to match the three different versions of the
hardware block that this driver supports.
This will change the prefix of the console messages produced by this
driver to be prefixed by s3c-mci instead of the hardware block name, such
as s3c2440-mci.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the local definition RESSIZE() with the standard resource_size()
call for getting the size of a struct resource.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In charge/uncharge/reclaim path, usage_in_excess is calculated repeatedly
and it takes res_counter's spin_lock every time.
This patch removes unnecessary calls for res_count_soft_limit_excess.
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch clean up/fixes for memcg's uncharge soft limit path.
Problems:
Now, res_counter_charge()/uncharge() handles softlimit information at
charge/uncharge and softlimit-check is done when event counter per memcg
goes over limit. Now, event counter per memcg is updated only when
memory usage is over soft limit. Here, considering hierarchical memcg
management, ancesotors should be taken care of.
Now, ancerstors(hierarchy) are handled in charge() but not in uncharge().
This is not good.
Prolems:
1. memcg's event counter incremented only when softlimit hits. That's bad.
It makes event counter hard to be reused for other purpose.
2. At uncharge, only the lowest level rescounter is handled. This is bug.
Because ancesotor's event counter is not incremented, children should
take care of them.
3. res_counter_uncharge()'s 3rd argument is NULL in most case.
ops under res_counter->lock should be small. No "if" sentense is better.
Fixes:
* Removed soft_limit_xx poitner and checks in charge and uncharge.
Do-check-only-when-necessary scheme works enough well without them.
* make event-counter of memcg incremented at every charge/uncharge.
(per-cpu area will be accessed soon anyway)
* All ancestors are checked at soft-limit-check. This is necessary because
ancesotor's event counter may never be modified. Then, they should be
checked at the same time.
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__css_put() doesn't check a bug as refcnt goes to minus.
I think it should be caught. This patch adds a check for it.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__mem_cgroup_largest_soft_limit_node() returns a mem_cgroup_per_zone "mz"
with incremnted mz->mem->css's refcnt. Then, the caller of this function
has to call css_put(mz->mem->css).
But, mz can be !NULL even if "not found" i.e. without css_get(). By
this, css->refcnt will go down to minus.
This may cause various things...one of results will be
initite-loop in css_tryget() as this.
INFO: RCU detected CPU 0 stall (t=10000 jiffies)
sending NMI to all CPUs:
NMI backtrace for cpu 0
CPU 0:
<snip>
<<EOE>> <IRQ> [<ffffffff810884bd>] trace_hardirqs_off+0xd/0x10
[<ffffffff8102a940>] flat_send_IPI_mask+0x90/0xb0
[<ffffffff8102a9c9>] flat_send_IPI_all+0x69/0x70
[<ffffffff81027372>] arch_trigger_all_cpu_backtrace+0x62/0xa0
[<ffffffff810bff8e>] __rcu_pending+0x7e/0x370
[<ffffffff810c02c7>] rcu_check_callbacks+0x47/0x130
[<ffffffff81063a26>] update_process_times+0x46/0x70
[<ffffffff81085930>] tick_sched_timer+0x60/0x160
[<ffffffff810858d0>] ? tick_sched_timer+0x0/0x160
[<ffffffff8107a03a>] __run_hrtimer+0xba/0x150
[<ffffffff8107a325>] hrtimer_interrupt+0xd5/0x1b0
[<ffffffff81426dfe>] ? trace_hardirqs_off_thunk+0x3a/0x3c
[<ffffffff8142cacd>] smp_apic_timer_interrupt+0x6d/0x9b
[<ffffffff8100cb33>] apic_timer_interrupt+0x13/0x20
<EOI> [<ffffffff811317b6>] ? mem_cgroup_walk_tree+0x156/0x180
[<ffffffff811316d3>] ? mem_cgroup_walk_tree+0x73/0x180
[<ffffffff81131692>] ? mem_cgroup_walk_tree+0x32/0x180
[<ffffffff81131a00>] ? mem_cgroup_get_local_stat+0x0/0x110
[<ffffffff81131d5b>] ? mem_control_stat_show+0x14b/0x330
[<ffffffff810a57fd>] ? cgroup_seqfile_show+0x3d/0x60
Above shows CPU0 caught in css_tryget()'s inifinite loop because
of bad refcnt.
This is a fix to set mz=NULL at the top of retry path.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some configurations of the Timberdale FPGA has the uartlite
included.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch size comment is like so last millenium. Update it to modern
times.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some manufacturers provide vendor information in non-vendor specific CIS
tuples. For example, Broadcom uses an Extended Function tuple to provide
the MAC address on some of their network cards, as in the case of the
Nintendo Wii WLAN daughter card.
This patch allows passing whitelisted FUNCE tuples unknown to the SDIO
core to a matching SDIO driver instead of rejecting them and failing.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The page_address_in_vma() is not only used in unuse_vma().
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just like ip_fast_csum, the assembly snippet in csum_ipv6_magic needs a
memory clobber, as it is only passed the address of the buffer, not a
memory reference to the buffer itself.
This caused failures in Hurd's pfinetv4 when we tried to compile it with
gcc-4.3 (bogus checksums).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix some build failures when using gcc-4.x for MN10300.
Firstly, __get_user() fails to build because the pointer points to a const and
__gu_val ends up being read-only:
In file included from include/linux/mempolicy.h:62,
from init/main.c:50:
include/linux/pagemap.h: In function 'fault_in_pages_readable':
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
make[1]: *** [init/main.o] Error 1
Secondly, gcc-4 doesn't allow casts of lvalues:
UPD include/linux/compile.h
arch/mn10300/kernel/rtc.c: In function 'calibrate_clock':
arch/mn10300/kernel/rtc.c:170: error: lvalue required as left operand of assignment
arch/mn10300/kernel/rtc.c:172: error: lvalue required as left operand of assignment
make[1]: *** [arch/mn10300/kernel/rtc.o] Error 1
These are seen with gcc 4.2.1.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Tomas Cech <sleep_walker@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 45d80eea87 ("m68k: convert to
asm-generic/hardirq.h") - it fails to compile due to an inclusion tangle:
In file included from include/linux/irq.h:12,
from include/asm-generic/hardirq.h:6,
from /usr/src/devel/arch/m68k/include/asm/hardirq_mm.h:6,
from /usr/src/devel/arch/m68k/include/asm/hardirq.h:4,
from include/linux/hardirq.h:10,
from /usr/src/devel/arch/m68k/include/asm/system_mm.h:69,
from /usr/src/devel/arch/m68k/include/asm/system.h:4,
from include/linux/list.h:7,
from include/linux/preempt.h:11,
from include/linux/spinlock.h:50,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:56,
from arch/m68k/kernel/asm-offsets.c:14:
include/linux/smp.h:17: error: field 'list' has incomplete type
Cc: Christoph Hellwig <hch@lst.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The asm-generic/gpio.h header uses the might_sleep() macro but doesn't
include the header for it, so any source code that might include
linux/gpio.h before linux/kernel.h can easily lead to a build failure.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/input/input.c:1277: warning: 'input_dev_reset' defined but not used
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Starting from commit 4a4962263f "reduce
symbol table for loaded modules (v2)", the kernel/module.c build is broken
with CONFIG_KALLSYMS disabled.
CC kernel/module.o
kernel/module.c:1995: warning: type defaults to 'int' in declaration of 'Elf_Hdr'
kernel/module.c:1995: error: expected ';', ',' or ')' before '*' token
kernel/module.c: In function 'load_module':
kernel/module.c:2203: error: 'strmap' undeclared (first use in this function)
kernel/module.c:2203: error: (Each undeclared identifier is reported only once
kernel/module.c:2203: error: for each function it appears in.)
kernel/module.c:2239: error: 'symoffs' undeclared (first use in this function)
kernel/module.c:2239: error: implicit declaration of function 'layout_symtab'
kernel/module.c:2240: error: 'stroffs' undeclared (first use in this function)
make[1]: *** [kernel/module.o] Error 1
make: *** [kernel/module.o] Error 2
There are three different issues:
- layout_symtab() takes a const Elf_Ehdr
- layout_symtab() needs to return a value
- symoffs/stroffs/strmap are referenced by the load_module() code
despite being ifdefed out, which seems unnecessary given the noop
behaviour of layout_symtab()/add_kallsyms() in the case of
CONFIG_KALLSYMS=n.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
