Add armclk to the supported clocks on the S3C2440 and S3C2442 to
better represent the DVS state which controls whether FCLK or HCLK
is fed to the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge together the bits of the S3C2440 and S3C2442 clock code
that can be.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the reverse of s3c2410_gpio_getirq to convert
a IRQ number into a GPIO pin number.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove warnings left in include/asm-arm/arch-s3c2410/debug-macro.S
whilst these where being experimented with.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the S3C2412 fclk is derived from msysclk, not straight from
the MPLL output. Set clk_f.parent appropriately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The msysclk clock was checking for the wrong PLL for the
parent in s3c2412_setparent_msysclk(), trying the UPLL instead
of the MPLL output.
Also ensure the mpll and fclks are at the same rate at init time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add S3C2412_CLKDIVN_DVSEN and S3C2412_CLKDIVN_HALFHCLK definitions to
the S3C2412_CLKDIVN set.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the channel parameter to s3c2410_dma_ctrl() in s3c2410_dma_enqueue()
if the S3C2410_DMAF_AUTOSTART is set on the channel.
Spotted by Steven Ryu at Samsung.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The s3c2410_dma_request() function should return the channel allocated
instead of zero for success.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add control constants for the S3C2412 SPI unit FIFO.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add definitions to allow easier decomposotion of the contents of
the S3C2410_BANKON registers
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The core resume code may have caused glitches in the GPIO when
restoring the GPIO state due to the order in which the GPIO registers
were being written.
Change the restore process take into account the state of the
GPIOs on resume and the state the system wants to restore them to.
See the code comments in the patch for more details of the process.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the call s3c2410_gpio_getpull() to return the
current state of the pin's pull-up.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure FIQ_START is defined to allow anyone to use FIQ code on
an S3C24XX based CPU.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an DMA channel was active at suspend, then ensure that
it is correctly reconfigured when the system resumes.
Note, the previous policy was for each driver to handle their
own reconfiguration on resume. The policy has been changed to
make the individual driver's job easier.
Signed-off-by: Ben Dooks <ben-linux@flfuf.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current S3C24XX DMA code does not allow for an peripheral
that has one channel for RX and another for TX.
This patch adds a per-cpu dma operation to select the transmit
or receive channel, and adds support to the S3C2412 for the
seperate DMA channels for TX and RX.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add s3c2412_gpio_set_sleepcfg() to allow the setting of the sleep
configuration of the GPIO blocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add armclk to the S3C2412 to indicate the current clock connected to
the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add checks for clk_set_rate() and ensure that we do not allow set_rate
to be called for a clock that does not have it defined. Add default
methods for fclk, hclk, pclk and mpll.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes compilation error if only a machine with
s3c2442 cpu is selected but without s3c2440 cpu selected.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check if the sleep command returns due to a pending interrupt
in the standby unit. If this happens, try and ack the IRQ
before re-trying the resume.
It is currently unclear whether the resume can be backed out
of at this stage as this could cause a problem with level
based interrupts.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that if the RTC IRQ is not selected for wake in the
base configuration, then the PWRCFG has the same value set
in it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2412_GPESLPCON does not exist in the register
mappings, so remove it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 IIS engine differs from the previous
SoC in the range, so add a set of register definitions
in a seperate file for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS and SDI register hw_addr definitions are
incorrect in the DMA map for the S3C2412.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 GPIO is similar enough to the S3C2410 that
it can use it as a base for GPIO functionality.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have a default display set to 4, when we only have
three registered displays. Fix this argument (a seperate
patch has been generated to ensure that the LCD driver
takes notice of this bug)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the watchdog reset fails and we decided to take the jump
to zero approach, allow 50ms for the UARTS to drain the FIFOs
before calling into a bootloader that may flush the output.
Also reduece the waits and the timeout values as 5 seconds is
rather long.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the hard reset routine is using the watchdog, then
ensure that the clock for the watchdog has been enabled
before we try and issue a reset.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the S3C2412_PWRCFG values for the action taken on detecting that
the battery is flat.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds back the registration of HWUART clock on pxa25x
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the xtime write mode seqlock into timer_tick(), so it only
surrounds the call to do_timer().
This avoids a deadlock in update_process_times() ...
hrtimer_get_softirq_time() which tries to get a read mode seqlock
on xtime, thereby preventing booting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original code incorrectly returns Hz instead of KHz.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (54 commits)
MAINTIANERS: just use Mike gmail e-mail for contact and pawn the serial driver off onto Sonic
[Blackfin] arch: remove old I2C BF54x porting.
[Blackfin] arch: Add the semtimedop syscall. Upstream uClibc doesn't compile without it.
[Blackfin] arch: fix bug kernel boot message: memory information is not reasonable
[Blackfin] arch: use common flash driver to setup partitions rather than the bf5xx-flash driver
[Blackfin] arch: Fix bug - kernel build with Debug option enabled fails to boot up
[Blackfin] arch: Fix bug Only RTC interrupt can wake up deeper sleep core.
[Blackfin] arch: Add proper SW System Reset delay sequence
[Blackfin] arch: Update copyright date
[Blackfin] arch: GPIO API cleanup and anomaly update
[Blackfin] arch: Fix BUG gpio_direction_output API is not compatitable with GENERIC_GPIO API interface
[Blackfin] arch: Initial checkin of the memory protection support.
[Blackfin] arch: set_bfin_dma_config shouldnt set SYNC or RESTART by default - add argument or option
[Blackfin] arch: Add some comments - fix semicolons
[Blackfin] arch: move all code related to CPLB handling into a new subdirectory under kernel/
[Blackfin] arch: print out list of modules if kernel is crashing and tell people if the kernel is tainted
[Blackfin] arch: enable generic GPIO based I2C driver in STAMP-BF533, EZKIT-BF533 and EZKIT-BF561 boards
[Blackfin] arch: Don't oops_in_progress if single step is comming from the kernel
[Blackfin] arch: Fix BUG - kernel sometimes would stuck with KEYBOARD_GPIO on
[Blackfin] arch: update to latest anomaly sheets
...
From: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
On the at92sam9263ek board, tell the input subsystem about the buttons.
This patch is taken from Andrew Victor's at91 patchset, then updated to
match the latest kernel code and to use labels printed on the board.
Also update the at91sam9261ek buttons to cope with input changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All the users of this driver explicitly specify the I2C bus numbers
to be used in their platform data. Make the driver respect that.
Signed-off-by: Kalle Pokki <kalle.pokki@eke.fi>
Cc: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the i2c-au1550 bus driver to platform driver, and
register a platform device for the Alchemy Db/Pb series of
boards.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Zero-bytes transfers would leave the bus transaction unfinished
(no i2c stop is sent), with the following transfer actually
sending the slave address to the previously addressed device,
resulting in weird device failures (e.g. reset minute register
values in my RTC).
This patch instructs the controller to send an I2C STOP right after
the slave address in case of a zero-byte transfer.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Propagate the error values returned by i2c_wait() instead of overriding
them with a meaningless -1.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This adds a i2c_new_dummy() primitive to help work with devices
that consume multiple addresses, which include many I2C eeproms
and at least one RTC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It is no longer required to hold adapter->clist_lock to call
i2c_check_addr.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
This goes on top of the patch removing most i2c_adapter.clients usage,
updating i2c_attach_client:
- Don't call device_register() while holding clist_lock. This
removes a self-deadlock when on the i2c_driver.probe() path,
for drivers that need to attach new devices (e.g. dummies).
- Remove a redundant address check. The driver model core does
this as a consequence of guaranteeing unique names.
- Move the "device registered" diagnostic so that it never lies;
previously, on error paths it would falsely report success.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The redundant i2c client list maintained by i2c-core is going away
soon, so drivers should stop using it now. Instead, they can use the
standard iterator provided by the device driver model
(device_for_each_child).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Michael Hunold <michael@mihu.de>
The i2c_adapter.clients list of i2c_client nodes duplicates driver
model state. This patch starts removing that list, letting us remove
most existing users of those i2c-core lists.
* The core I2C code now iterates over the driver model's list instead
of the i2c-internal one in some places where it's safe:
- Passing a command/ioctl to each client, a mechanims
used almost exclusively by DVB adapters;
- Device address checking, in both i2c-core and i2c-dev.
* Provide i2c_verify_client() to use with driver model iterators.
* Flag the relevant i2c_adapter and i2c_client fields as deprecated,
to help prevent new users from appearing.
For the moment the list needs to stick around, since some issues show
up when deleting devices created by legacy I2C drivers. (They don't
follow standard driver model rules. Removing those devices can cause
self-deadlocks.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
